Eaton Airflex WCB Series | Water Cooled Brake Model Range

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply compatible replacements for the EATON AIRFLEX WCB water cooled brake series. The WCB series includes air-applied, water-cooled brake elements in both inch-based (8WCB to 48WCB) and size-code-based (108WCB to 448WCB) designations. These units are designed for continuous slip and high-heat braking on drawworks and workover rigs. Eaton Airflex® is a registered trademark of Eaton Corporation. HYRIG is an independent supplier of compatible replacement products and is not affiliated with, authorized by, or endorsed by Eaton Corporation.
Conatct For Details
DetailReview(0)Additional

Key Facts

AttributeValue
Product TypeAir-applied, water-cooled brake elements
Compatible SeriesEATON AIRFLEX WCB / WCB2 configurations
DutyContinuous slip / high-heat braking
CoolingWater-cooled friction interface
DesignationsInch-based (8WCB) & Size-code (114WCB)
Typical HostDrawworks, workover rigs, winches
Replacement CompatibilityForm-fit-function replacement; verify flange bolt pattern and water port thread

> Data source: Technical data table.

Eaton Airflex WCB Model Range

The WCB series uses two naming conventions in the field. The table below maps these designations to help you identify your existing unit.

Inch DesignationSize-Code DesignationPlatesTypical ApplicationDetail Page
8WCB108WCB1Light auxiliary brakingContact HYRIG
14WCB114WCB1Standard drawworksView 114WCB
—214WCB2Medium duty drawworksView 214WCB
18WCB118WCB1Standard workover rigsContact HYRIG
24WCB124WCB1Standard drawworksView 124WCB
36WCB236WCB2Heavy-duty drawworksView 236WCB
36WCB336WCB3Heavy-duty high heatView 336WCB
48WCB418WCB4High-torque drawworksView 418WCB
48WCB248WCB / 448WCB2 / 4High-torque applicationsContact HYRIG

Note: For specific dual-acting or severe-duty variants not listed above, please contact HYRIG engineering.

Dimensions

Dimension ItemReference / Action
Mounting FlangeMeasure existing adapter hole spacing center-to-center; do not rely on the model code alone
Water Port Thread1/4 SAE ORB is standard, but confirm against your existing coolant hoses
Overall Housing ProfileConfirm clearance dimensions against your installation envelope
WeightVaries significantly by disc count and size; confirm lifting plan with HYRIG

Structure / Working Principle

The WCB series uses air pressure to clamp friction discs against water-cooled wear plates. Coolant circulates through the jackets to carry away heat generated during continuous slip. This design keeps friction surface temperatures stable in sustained braking—the key requirement for drawworks where the brake is engaged for long periods rather than as an emergency stop.

Cross-Reference & Replacement

Replacing an Airflex WCB unit? Here is what to verify before ordering:

  1. Identify the designation — check if your nameplate uses the inch system (e.g., `36WCB`) or the size-code system (e.g., `236WCB`).
  2. Mounting flange bolt pattern — measure the existing hole spacing. Revisions can change flange patterns.
  3. Water port thread — confirm your coolant line fitting standard.
  4. Actuation type — confirm whether your existing unit is air tube type or piston type.
  5. Friction disc wear — measure the existing disc thickness.

Searching for "114WCB Clutch and Brake"?
The 114WCB (and 214WCB) are primarily water-cooled brakes for continuous slip. If your application requires clutch engagement/disengagement combined with braking, you must verify the specific mounting arrangement with HYRIG engineers before ordering.

Cross-Brand Boundary:
Wichita also uses similar WCB designations (e.g., Wichita 114WCB). Wichita and Airflex units use different flange and port configurations. Do not assume cross-brand drop-in compatibility. Confirm interface measurements with HYRIG engineers.

Selection Support

Not sure which WCB model fits your drawworks? Send HYRIG the existing unit's nameplate photo, flange bolt pattern measurements, and water port thread size. Engineers will confirm the compatible element and quote with lead time. You can also browse our WCB water cooled brake parts for wear components.

Frequently Asked Questions

Q: Are these original Eaton Airflex products?
No. HYRIG supplies independent, compatible replacement products and is not affiliated with Eaton Corporation.

Q: What is the difference between 8WCB and 108WCB?
They refer to the same basic platform using different naming conventions (inch vs. size code). Confirm the exact code on your nameplate and measure the interface dimensions.

Q: What is the lead time for WCB series replacements?
Standard lead time is quoted per order based on configuration and quantity; for urgent downtime, confirm with HYRIG engineers at inquiry.

Q: Can I replace a Wichita WCB with an Airflex WCB?
No. Wichita and Airflex WCB units use different flange and port configurations. Do not assume drop-in compatibility. Confirm interface measurements with HYRIG engineers.

Contact

For WCB water cooled brake series selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing unit nameplate photo
  • Mounting flange bolt pattern measurements
  • Water port thread type/size
  • Required quantity

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit