Slurry Pump – API 610 Types OH2, BB2, VS4, VS6 for Heavy Duty Abrasive Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 Slurry Pump OH2, BB2, VS4, VS6 – heavy duty centrifugal pumps for abrasive, high‑solids fluids in oil shipping. Handle sand laden crude (5‑20% sand), drilling mud (30‑60% solids), ballast sludge. Horizontal OH2/BB2 for deck, vertical VS4/VS6 for submerged tight spaces. Double shell with high chrome or rubber lining. Semi‑open impeller, API 682 dual mechanical seals. Flow 50‑2000 m³/h, head 20‑150 m, solids up to 60%. NACE MR0175 optional.
Conatct For Details
DetailReview(0)Additional

The Slurry Pump OH2, BB2, VS4, and VS6 are API 610 heavy duty centrifugal pumps specifically engineered for transporting solid‑liquid mixtures with high concentration of abrasive particles. In oil shipping – sand laden crude (5‑20% sand), drilling mud (30‑60% solids), ballast water sludge, and tank washing residues – these pumps handle fluids that would quickly destroy ordinary centrifugal pumps. Their defining features: extreme wear resistance, large flow passages, anti‑clogging design, and compliance with API 610 and API 682.

This guide covers all four major API 610 slurry pump configurations: OH2 (overhung horizontal), BB2 (between‑bearing double suction), VS4 (vertical long shaft), and VS6 (vertical short shaft/submersible). Whether you need a deck‑mounted horizontal pump or a submerged vertical pump for confined spaces, our slurry pump range meets your requirements.


API 610 Slurry Pump OH2 – Horizontal Overhung Configuration

OH2 slurry pump is a single‑stage, end suction, overhung, centerline‑mounted centrifugal pump. It is the most common choice for deck‑mounted abrasive service.

  • Construction: Double shell – outer casing pressure‑containing, inner liner high chrome iron or rubber. Semi‑open or open impeller with wide passages.

  • Flow range: 50 – 2000 m³/h

  • Head range: 20 – 150 m

  • Applications: Sand laden crude transfer, drilling mud circulation, abrasive slurry pumping.

Why OH2 for slurry? Easy maintenance (back pull‑out design), compact footprint, handles solids up to 10 mm with semi‑open impeller.


BB2 Slurry Pump – Double Suction Between Bearing Design

BB2 slurry pump is a horizontal, radially split, single‑stage double‑suction pump with impeller between two bearing sets. Designed for higher flow and higher head than OH2.

  • Construction: Double shell, double‑suction impeller (balanced axial thrust), wide flow passages.

  • Flow range: 200 – 5000 m³/h

  • Head range: 30 – 180 m

  • Applications: High‑capacity drilling mud circulation, large volume ballast sludge, high flow abrasive transfer.

Why BB2 for slurry? Very high flow capacity, low NPSH requirement, axial thrust balanced, longer wear life in continuous heavy duty.


VS4 / VS6 Vertical Slurry Pump – Submerged & Space Saving

VS4 and VS6 slurry pumps are vertically suspended, single or multistage, with pump bowl submerged in the fluid. The difference: VS6 has shorter shaft (shallow sump), VS4 uses longer shaft (deep pit or tank). Both are ideal for confined spaces and below‑deck installation.

  • Construction: Single or double shell, vertical column pipe, submerged bearing(s) for long shaft.

  • Flow range: 100 – 1500 m³/h

  • Head range: 15 – 80 m

  • Applications: Cargo tank bottom sand slurry, sludge tank evacuation, scrubber slurry circulation, ballast water sludge from deep tanks.

Why VS4/VS6 for slurry? Small footprint, self‑priming (submerged), handles sloshing and vessel motion, easy installation in tight spaces.


Key Oil Shipping Applications – Slurry Pump OH2 BB2 VS4 VS6

ApplicationFluid CharacteristicsRecommended TypeKey Parameters
Sand laden crude oilSand 5–20%, particle ≤5 mm, T ≤80°COH2 horizontal slurry pumpFlow 100‑500 m³/h, head 30‑80 m, high chrome A05 liner
Drilling mud circulationSolids 30‑60%, cuttings, clayBB2 double suction slurry pumpFlow 200‑1000 m³/h, head 50‑120 m, open impeller
Ballast water sludgeSand/silt 10‑30%, particles ≤10 mmVS6 vertical slurry pumpFlow 300‑800 m³/h, head 20‑50 m, rubber liner
Tank washing residuesOil sludge, sand, pH 6‑9VS4 vertical slurry pumpFlow 50‑300 m³/h, head 15‑40 m, API 682 seals

Critical Design Features for Slurry Pumps

Materials

  • High chrome cast iron (A05/A49): Hardness 600+ Brinell – for highly abrasive particles (sand, coke, ore).

  • Rubber lining (natural rubber, NBR, EPDM): Excellent for fine, soft particles – reduces wear and lowers cost.

  • Duplex stainless steel: For corrosive slurries (sour, saline, chemical) with moderate abrasion.

Impeller Types

  • Semi‑open: Best balance of efficiency and clog resistance – most common for slurry.

  • Open impeller: For very large particles or high solids (>30%) – lowest clog risk.

  • Closed impeller: Only for fine particles (<2 mm) and low solids (<10%) – higher efficiency.

API 682 Mechanical Seals

All slurry pumps must prevent leakage of abrasive, often hazardous, fluids.

  • Standard: Dual mechanical seals with external flush or barrier fluid.

  • Recommended plans: Plan 32 (external clean flush), Plan 53A/53B (pressurised dual seals).

  • Prohibited: Packed gland.


Comparison – Slurry Pump vs. Standard API 610 OH2 Clean Fluid Pump

FeatureSlurry Pump (OH2/BB2/VS4/VS6)Standard API 610 OH2 Clean Fluid Pump
FluidSolids 5‑60%, abrasive, high viscosityClean liquids, low viscosity
Flow passageWide, no narrow gaps, anti‑cloggingStandard clearances, efficiency optimized
Wetted materialHigh chrome / rubber lining, thick sectionsCast iron / 316L, standard thickness
Impeller typeSemi‑open or openClosed (high efficiency)
Wear life in abrasive service6‑24 months1‑3 months (rapid failure)
CostHigher (wear resistant alloys and liners)Lower

Selection Guidelines – Which Slurry Pump Do You Need?

  1. For deck mounting with good space: Choose OH2 or BB2 horizontal.

    • OH2: flow <2000 m³/h, head <150 m.

    • BB2: flow >2000 m³/h, head up to 180 m.

  2. For confined spaces, tanks, or below‑deck: Choose VS4 or VS6 vertical.

    • VS6: shallow sump, short shaft, easy retrieval.

    • VS4: deep pit or tank, long shaft with intermediate bearings.

  3. For highly abrasive sand, sharp particles: High chrome iron (A05) – OH2 or BB2.

  4. For fine, soft silt or clay: Rubber lining – any type.

  5. For corrosive + abrasive slurries (sour, salt water): Duplex stainless steel – all types available.


Frequently Asked Questions (FAQ)

Q: What is the difference between Slurry Pump OH2 and BB2?
A: OH2 is an overhung single‑stage pump with impeller at shaft end; BB2 is a between‑bearing double‑suction pump with impeller between two bearings. BB2 handles higher flow and better axial thrust balance.

Q: When to use VS4 vs VS6 for slurry service?
A: VS6 uses a short shaft and is suitable for shallow pits or sumps. VS4 uses a longer shaft with intermediate bearings for deep tanks or caissons (depth >3 m). Both are vertically suspended and submerged.

Q: Can I use a standard API 610 OH2 pump for sand laden crude?
A: No. Standard OH2 pumps (clean service) will wear out within weeks. You must use a true slurry pump with high chrome or rubber lining, semi‑open impeller, and API 682 dual seals.

Q: What is the maximum particle size your slurry pumps can handle?
A: For OH2/BB2: up to 10 mm with semi‑open impeller, 25 mm with open impeller. For VS4/VS6: up to 15 mm depending on impeller design.

Q: Do you provide NACE MR0175 compliant slurry pumps for sour crude?
A: Yes. All our slurry pump types (OH2, BB2, VS4, VS6) can be supplied with duplex stainless steel or super duplex materials and NACE certification.


Standards & Compliance

  • API 610 (12th Edition): OH2, BB2, VS4, VS6 structural types, rigid shaft, bearing design.

  • API 682: Mechanical seals for slurry service – Plans 32, 53A, 53B.

  • IMO MARPOL: Low emission seals for oily water discharge compliance.

  • NACE MR0175 (optional) for sour service.


Contact Us for Slurry Pump OH2 BB2 VS4 VS6

If you are searching for a Slurry Pump OH2, BB2, VS4, or VS6 – for sand laden crude, drilling mud, ballast sludge, or any abrasive high‑solids fluid – we have the right API 610 heavy duty solution. Provide your flow, head, solids concentration, particle size, and installation space. We will recommend the exact pump type and materials.

Email: info@hyrig.com
Response within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit