The Condensate Pump (also known as condensate extraction pump) is an API 610 Type VS6 vertical, single‑casing, multistage, diffuser‑type centrifugal pump specifically engineered for pumping condensate from hot well receiver sumps, condenser hot wells, or other collection pits. The pump handles hot water and condensate at elevated temperatures and moderate pressures, transferring the fluid to deaerators, boiler feed systems, or downstream processes.
In power plants, industrial boiler houses, and process industries, condensate is the liquid formed when steam condenses after releasing its heat. This condensate is typically at near‑saturation temperature (approximately 90°C in many systems) and must be recovered efficiently to conserve energy and water. The condensate pump operates under low available Net Positive Suction Head (NPSH) conditions — often less than 1–2 meters — making a vertical can‑type or VS6 configuration essential for reliable, cavitation‑free operation.
The VS6 configuration features a vertical, close‑coupled (or separated) driver arrangement with a single casing that is submerged or partially submerged in the sump. The pump shaft is vertical, and the multistage diffuser and impeller assembly is suspended below the discharge head. Liquid enters the pump through a suction bell or strainer, passes through successive stages, and is discharged through a column pipe and discharge head. This design provides excellent NPSH characteristics (low NPSH required) and is ideal for handling hot condensate near boiling point.
As a specialized China VS6 pump manufacturer, we produce fully API 610 11th Edition (ISO 13709) compliant pumps for condensate extraction, hot water pit services, and other vertical sump applications in power generation, refining, petrochemical, and general industry.
The Condensate Pump is specifically engineered for handling hot condensate and hot water in a variety of industrial services:
Primary Media:
Condensate — condensed steam from turbines, heat exchangers, reboilers, and steam heating systems
Hot water — recirculated hot water at elevated temperatures
Boiler feed water — make‑up water or recycled condensate
District heating return water — hot water from heating networks
Typical Fluid Properties at Specified Duty:
Medium: Clean or slightly contaminated hot water / condensate
Temperature: 90°C (design range: -20°C to +200°C; higher available with special materials)
Pressure: 1.2 MPa (12 bar) discharge pressure (suction at atmospheric or slight vacuum)
Characteristics: Non‑corrosive to slightly corrosive (depending on purity and chemical treatment), near boiling point at suction conditions
NPSH available: Often very low (0.5 – 2 meters) — VS6 pump with submerged impeller offers excellent low‑NPSH capability
Extended Applications (Same Pump Platform):
Power plant condenser hot well extraction
Industrial condensate return systems (pulp & paper, steel mills, chemical plants)
Boiler feed water booster pumps (from atmospheric deaerator storage tank)
Hot water circulation pumps with low suction lift
Sump and pit drainage for hot or cold water
Seawater lift pumps (with material upgrades)
Raw water intake pumps from rivers or sumps
Circulating water pumps with low NPSH
The API 610 VS6 vertical multistage condensate pump covers a wide operating envelope:
| Parameter | Value / Range |
|---|---|
| Pump Type | API 610 Type VS6 – Vertical, single casing, multistage, diffuser type |
| Flow Rate (Q) | 10 ~ 2,000 m³/h (selectable based on condensate volume) |
| Total Head (H) | 20 ~ 1,200 m (staged to meet system pressure requirement) |
| Operating Temperature | 90°C (design range: -20°C to +200°C; up to 350°C with cooling) |
| Discharge Pressure | 1.2 MPa (12 bar) typical; pump rating up to 10 MPa |
| Speed (rated) | 1,450 / 2,950 rpm (direct motor drive) |
| Casing Construction | Vertical, single casing, diffuser type with column pipe |
| Impeller Type | Enclosed (standard) or open (non‑clog), multistage |
| Suction Type | Submerged suction bell or strainer (low NPSH design) |
| Discharge Orientation | Horizontal or vertical (through discharge head) |
| Flange Rating | ASME Class 150 / 300 |
| Materials | Cast iron, carbon steel, 304/316 SS, duplex SS |
| Shaft Power | Up to 1,500 kW depending on flow and head |
Note: The specified duty (water/condensate at 90°C, 1.2 MPa) falls well within the standard operating envelope of VS6 pumps. Number of stages is selected to provide the required discharge pressure at the rated flow.
The API 610 VS6 condensate pump incorporates a comprehensive suite of design features specifically optimized for hot condensate service with low NPSH:
| Feature | Description |
|---|---|
| Vertical Configuration | Pump is installed vertically with the driver mounted on top of a discharge head. The hydraulic assembly is submerged in the condensate sump or hot well. This allows the pump to operate under low NPSH conditions by using the static head of the liquid column above the first stage impeller. |
| Multistage Diffuser Type | Multiple stages (2 to 15+) arranged in series, each consisting of a diffuser bowl and an impeller. Diffusers convert velocity energy to pressure efficiently and provide smooth flow transition between stages. The diffuser type casing is inherently balanced radially, reducing shaft deflection and extending bearing and seal life. |
| Low NPSH Design | The first stage impeller is submerged below the minimum operating liquid level, providing sufficient static head to prevent cavitation. For extremely low NPSH conditions, a double‑suction first stage or an inducer can be added. This is critical for condensate near boiling point (90°C) where NPSH available is often minimal. |
| Suction Bell / Strainer | A suction bell (bellmouth) or conical strainer is attached to the pump suction to provide smooth, uniform flow entry and prevent large debris from entering the pump. Strainers are easily removable for cleaning during maintenance. |
| Column Pipe & Line Shaft | The pump column pipe houses the line shaft that transmits torque from the motor to the impeller stack. Column pipe sections are flanged and bolted together, with steady bearings at regular intervals to support the line shaft and prevent whirling. API 610 requires steady bearings at intervals determined by critical speed analysis. |
| Discharge Head | The discharge head is the topmost casting that supports the motor, contains the discharge nozzle, and houses the discharge elbow. It also contains the mechanical seal housing (or stuffing box for packing) and provides a mounting surface for the motor stool. |
| Thrust Bearing Assembly | A heavy‑duty thrust bearing (typically angular contact or tilting pad) located in the discharge head supports the full axial thrust generated by all stages. The thrust bearing is oil‑lubricated (oil ring or forced oil) and includes a cooling jacket when handling high temperature condensate. |
| Line Shaft Steady Bearings | Intermediate steady bearings (sleeve type, water‑lubricated or product‑lubricated) are installed inside the column pipe at intervals (typically 1.5–2 meters) to support the line shaft. For condensate service at 90°C, water‑lubricated rubber bearings (or PTFE‑lined bronze) are common. |
| Mechanical Seals or Packing | The pump shaft passes through the discharge head into the column pipe. A mechanical seal (API 682 compliant) or packing (for less critical services) prevents liquid leakage. For hot condensate (90°C), a single mechanical seal with Plan 11 (recirculation + orifice) or Plan 21 (cooled recirculation) is typical. For higher temperatures or pressure, tandem seals with Plan 52 are used. |
| Impeller Types | • Enclosed impellers – standard for clean condensate, providing highest efficiency • Open (non‑clog) impellers – optional for condensate containing small amounts of rust, scale, or debris; reduced efficiency but better solids handling • All impellers are dynamically balanced to ISO 1940 Grade G2.5 |
| Wear Rings (Renewable) | Renewable casing and impeller wear rings provided on enclosed impeller stages to maintain efficiency over the pump lifetime. Hardened materials (12% Cr or SS with hard facing) resist galling. |
| Materials for Condensate Service | • Cast iron – acceptable for clean condensate at moderate temperatures (≤120°C) • Carbon steel – suitable for higher pressure/temperature • 304/316 stainless steel – recommended for condensate with low pH or aggressive treatment chemicals • Duplex stainless steel – for high velocity or aggressive condensate conditions |
| Bearing Lubrication & Cooling | • Thrust bearing: oil ring lubrication with constant level oiler; water cooling jacket optional for 90°C+ service • Line shaft steady bearings: water‑lubricated (condensate itself) — no external lubrication required |
| Motors and Driver Arrangement | • Close‑coupled motor mounted directly on discharge head (standard for smaller sizes) • Separated motor with flexible coupling and intermediate shaft (for larger sizes or high sump depths) • Motor type: TEFC, explosion‑proof as required |
Selecting appropriate materials for condensate and hot water service (90°C, 1.2 MPa) ensures long service life and reliable operation:
| Component | Standard Material (Clean Condensate) | Upgrade Option (Corrosive Condensate) |
|---|---|---|
| Suction Bell / Strainer | Cast iron or Carbon steel | 304SS / 316SS |
| Column Pipe (wetted) | Carbon steel | 304SS / 316SS |
| Discharge Head | Cast iron or Carbon steel | 304SS / 316SS / Duplex |
| Diffuser Bowls (Stages) | Cast iron (≤120°C) or Carbon steel | 304SS / 316SS / Duplex |
| Impellers (Enclosed) | Cast iron / 12% Cr steel | 304SS / 316SS / Duplex |
| Shaft (Line Shaft) | Carbon steel (AISI 4140) | 316SS / Duplex / 17‑4PH |
| Wear Rings | Hardened 12% Cr steel | 316SS with Stellite facing |
| Steady Bearings | Rubber (water‑lubricated) | PTFE‑lined bronze / Silicon carbide |
| Mechanical Seal Faces | Silicon carbide vs. carbon | Tungsten carbide vs. carbon |
| Gaskets / O‑rings | EPDM (for hot water) | FKM / PTFE |
| Fasteners | Carbon steel (B7) | Stainless steel (B8M) |
Recommendation for 90°C condensate service:
Clean condensate (neutral pH, low oxygen): Carbon steel column pipe + cast iron bowls/impellers provides an economical, long‑life combination.
Deaerated condensate pure water: 304SS or 316SS internal wetted parts provide superior corrosion resistance and eliminate red water issues.
Condensate with low pH (acidic) or aggressive chemicals: Upgrade to 316SS or duplex SS.
| System | Description for Condensate Service |
|---|---|
| Seal Flush Plan | For single mechanical seal: Plan 11 (internal recirculation from discharge with orifice) or Plan 21 (cooled recirculation using a heat exchanger) for 90°C service. For higher temperature, Plan 23 (recirculation with cooler and thermosiphon) is recommended. |
| Seal Cooling (when required) | Seal flush cooler (shell and tube) using cooling water to lower temperature to 40–60°C entering seal chamber. Extends seal life. |
| Bearing Cooling | Water cooling jacket around thrust bearing housing for condensate above 80°C to maintain bearing temperature within limits (typically ≤75°C). Cooling water flow regulated by thermostatic valve. |
| Minimum Flow Protection | Automatic recirculation valve (ARC) or control valve + orifice to ensure minimum flow when main discharge valve is closed. Prevents overheating of pump due to low flow (especially important for hot condensate). |
| Vibration Monitoring | Accelerometers mounted on discharge head (bearing housing) for velocity monitoring per API 670. Local and remote indication. |
| Bearing Temperature Monitoring | RTD (PT100) sensor in thrust bearing housing with local display and 4‑20 mA output for DCS alarm and trip. |
| Discharge Pressure Gauge | Mounted on discharge head, with dampener and isolation valve. |
| Suction Level Measurement | Level transmitter or controller in sump/hot well to maintain pump submergence and prevent vortexing or air ingestion. Low level interlock to protect pump. |
| Packing Box (if used) | Not typical for VS6 condensate pumps; mechanical seal is standard. If packing is specified, a lantern ring with Plan 32 (external clean water flush) is recommended to flush away scale and cool the packing. |
| Baseplate / Support Structure | Discharge head is bolted to a concrete foundation or steel support structure that aligns the pump vertically and supports the motor weight. Foundation plate with leveling screws and grouting. |
The condensate pump is a critical component in thermal power plants and industrial steam systems. The API 610 VS6 pump offers distinct advantages that align with the requirements of condensate service:
Superior low NPSH performance – The submerged impeller design provides the required NPSH even when condensate is near boiling point. Standard VS6 pumps can operate with as little as 0.5–1.5 meters of submergence above the first stage impeller.
Handles elevated temperatures – Designed for continuous operation at up to 200°C (or higher with special materials). The 90°C specified duty is well within the standard envelope.
Vertical installation minimizes floor space – The pump occupies only the footprint of the discharge head and motor, saving valuable plant floor space compared to horizontal pumps.
No priming required – The impeller stack is always submerged, so the pump is always primed and ready to start.
API 610 reliability – Heavy duty construction, fully compliant with API 610 11th Edition, ensures 3+ years between overhauls in continuous service.
Easy maintenance – The entire rotating element (line shaft + impeller stack + bowl assembly) can be withdrawn upward through the discharge head after removing the motor and coupling, without excavating the sump or pit.
Non‑clog design (optional) – For condensate that may contain small rust particles, scale, or debris, open impellers or non‑clog diffuser designs minimize plugging.
Beyond power plant condensate extraction, the VS6 pump serves numerous industries:
Power Generation:
Condenser hot well extraction pumps (steam turbine cycle)
Combined cycle plant condensate pumps
Boiler feed booster pumps (from deaerator storage tank)
District heating condensate return pumps
Refining & Petrochemical:
Condensate recovery from steam tracing systems
Return pumps for steam‑heated reboilers and heat exchangers
Pit drainage of hot condensate
Pulp & Paper:
Condensate recovery from paper machine dryers
Steam system condensate return pumps
Steel & Metals:
Hot water and condensate recovery from cooling beds and mill systems
Boiler house condensate extraction
Chemical Plants:
Condensate return from distillation columns and evaporators
Hot water circulation from reaction cooling loops
Food & Beverage / Pharmaceutical:
Clean condensate recovery from sterilizers, evaporators, and cooking kettles
Sanitary condensate pumps (SS316 construction, sanitary seals)
General Industry:
Any hot water or low‑temperature liquid pumping from sumps or pits with low NPSH available
As a specialized China VS6 pump manufacturer with extensive experience in condensate extraction and vertical multistage pumps, we provide:
Full API 610 11th Edition compliance – designed, manufactured, and tested to the same rigorous standards as leading global brands
Proven VS6 technology – used in hundreds of power plants and industrial facilities worldwide
Competitive capital cost – typically 20–35% lower than major Western brands for equivalent API 610 VS6 configurations
Shorter lead times – 16–24 weeks ARO for standard material configurations (cast iron / carbon steel)
Complete documentation package – including hydraulic performance curves, NPSH3 curves, sectional drawings, GA drawings, API 610 data sheets, material certifications, rotordynamics analysis for line shaft, and noise prediction
Factory performance testing – witnessed and non‑witnessed options; testing includes hydraulic performance, NPSH, mechanical run, and vibration monitoring on a certified test loop
Engineered-to-order design – column pipe length, number of stages, and material selection customized to your exact sump depth, flow, and head requirements
Global shipping – export‑capable packaging (wooden crates, VCI, desiccant) and full export documentation
Spare parts availability – critical spares (wear rings, bushings, seals, bearings, gaskets) stocked; full spare parts kits available for planned overhauls
Installation and commissioning support – on‑site supervision, training, and after‑sales service
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type VS6 – Vertical, single casing, multistage, diffuser type |
| Medium | Condensate / hot water |
| Specified Operating Condition | 90°C / 1.2 MPa discharge pressure |
| Design Temperature Range | -20°C to +200°C (higher with special materials) |
| Design Pressure Rating | Up to 10 MPa (depending on number of stages) |
| Typical Flow Range | 10 – 2,000 m³/h |
| Typical Head | 20 – 1,200 m |
| Casing Construction | Vertical single casing, diffuser type with column pipe |
| Impeller Type | Enclosed (standard) / open (non‑clog, optional) |
| First Stage Submergence | Low NPSH design – 0.5 m minimum |
| Materials (Recommended) | Cast iron / carbon steel (clean); 316SS (corrosive) |
| Seals | Mechanical seal with Plan 11/21 (single) or Plan 52 (tandem) |
| Lubrication | Oil ring (thrust bearing); water‑lubricated line shaft bearings |
| Maintenance | Rotating element withdrawable upward without removing column pipe |
| Certification | API 610 11th Edition / ISO 13709 |
For more information or a custom engineering proposal for your condensate pump (hot water, 90°C, 1.2 MPa) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.