Condensate Recovery Pump – API 610 VS2 Vertical Turbine Pump for High Temperature Condensate Return by Leading China 610 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS2 condensate recovery pump – vertical suspended, wet pit, single‑casing centrifugal pump engineered for collecting and returning high‑temperature steam condensate from low‑level pits, collection tanks, and process drains to the deaerator or boiler feedwater system. Vertical turbine design with submerged suction provides excellent low NPSH performance, essential for near‑saturation condensate. Flows to 1,000 m³/h, heads to 200 m, temperatures to 200°C. Carbon steel casing with stainless steel trim (impeller, shaft, wear rings) or all‑stainless steel. Back pull‑out for easy maintenance. Manufactured by a certified China API 610 pump manufacturer with API Q1 certification. 20‑year design life, 3‑year continuous operation.

Conatct For Details
DetailReview(0)Additional

Product Overview

A condensate recovery pump is a specialized vertical turbine pump designed to collect hot condensate – the liquid water formed when steam releases its latent heat – from low‑level collection points such as condensate pits, hot wells, flash tanks, and process drains, and then transfer it to the deaerator, boiler feedwater tank, or return main. Condensate recovery is essential for energy efficiency (reusing high temperature water reduces fuel consumption), water conservation, and chemical treatment savings.

The pump is classified under API 610 (ISO 13709) as Type VS2 – a vertical suspended, wet pit, single-casing diffuser or volute pump. The vertical turbine configuration is ideal for low NPSH service because the pump bowl is submerged below the condensate level, providing positive suction head even when the condensate is near its boiling point. This design eliminates priming concerns, handles intermittent flow, and provides long, trouble‑free operation in steam condensate service.

This pump is manufactured by a leading China API 610 pump manufacturer with full API Q1 certification, decades of experience in high‑temperature pumping, and thousands of VS2 pumps installed in condensate recovery and steam system applications worldwide.

Construction & API 610 Classification

FeatureDescription
API 610 TypeVS2 (vertical suspended, wet pit, single‑casing)
Casing formDiffuser type or volute type; single casing
SuctionSubmerged below condensate level; flooded suction
DischargeThrough column to surface discharge head
DriverSurface‑mounted electric motor (dry, accessible)
Number of stagesSingle‑stage (standard for low head) or multistage (for higher head)
Impeller typeRadial or mixed flow, single‑suction or double‑suction first stage
ShaftFlexible line shaft with intermediate sleeve bearings
Thrust bearingLocated in driver or discharge head, sized for hydraulic down‑thrust
ComplianceAPI 610 11th / 12th edition (ISO 13709)

Why VS2 for Condensate Recovery

Submerged suction for low NPSH – Condensate is often near its saturation temperature, leaving very low NPSH available. The VS2 pump's submerged bowl design ensures positive NPSH by virtue of the liquid column above the impeller. The vertical turbine type can be specially designed for low NPSH applications.

Vertical orientation – Saves floor space; pump is installed directly in the condensate pit or tank, requiring no separate suction piping.

No priming required – The impeller is always submerged, eliminating the need for foot valves, vacuum priming, or manual filling – critical for intermittent operation where condensate may flash to steam during idle periods.

High temperature capability – Designed for fluids up to 200°C (400°F), with proper materials, thermal expansion allowances, and seal selection.

Flexible setting depth – Column length is customised to the pit depth, allowing the pump to sit just above the pit bottom, maximizing condensate recovery down to low levels.

Easy maintenance – The rotating assembly can be withdrawn upward without draining the pit. The surface‑mounted motor remains dry and accessible.

Key Technical Specifications (Condensate Recovery Duty)

ParameterRange
Flow10 – 1,000 m³/h (45 – 4,400 GPM) – typical 20‑500 m³/h
Head15 – 200 m (50 – 655 ft) – typical 30‑100 m
TemperatureUp to 200°C (400°F)
Maximum pressureUp to 2.5 MPa (25 bar)
Setting depth (column length)Up to 15 m (custom longer on request)
Number of stages1 – 6 (depending on head)
Speed1,450 / 2,900 rpm (50Hz) or 1,750 / 3,550 rpm (60Hz) – slower speeds for low NPSH
Flange ratingANSI Class 150 / 300
NPSHrVery low (1‑3 m) due to submerged impeller and low‑NPSH first‑stage hydraulics
Design life20 years minimum

Materials – Carbon Steel + Stainless Steel Trim or All‑Stainless Steel

Condensate is typically deaerated and may be slightly acidic (pH 6‑7) due to dissolved CO₂, but generally not highly corrosive to carbon steel at moderate temperature. However, to prevent rust contamination and extend life, stainless steel internals are recommended.

ComponentStandard Material (Economical)Upgrade Material (Premium)Remarks
Discharge headCarbon steel (ASTM A216 WCB)304/316L stainless steelCarbon steel acceptable for most; stainless for aggressive condensate
Pump column / discharge pipeCarbon steel (epoxy coated)304/316L stainless steel–
Bowl assembly (diffuser/volute)Carbon steel or 304 SS316L stainless steelFor temperatures >150°C, 316L preferred
Impeller304 stainless steel or bronze316L stainless steel316L resists corrosion and erosion at high temperature
Shaft410 stainless steel or 4140 (coated)316 stainless steel or 17‑4 PH17‑4 PH has good high‑temperature strength
Wear rings304 SS + hard‑facing316L SS + Stellite–
Shaft sleeve410 SS or 316 SS316L SS–
Intermediate bearings (line shaft)Bronze‑backed rubber (water lubricated)Silicon carbide / PTFE–
Thrust bearing (in driver)Heavy‑duty angular contactKingsbury tilting padFor higher thrust loads
Fasteners304 SS or B7316 SS / Duplex–

Recommended material for condensate recovery

  • Typical condensate (pH 6‑8, temperature ≤150°C): Carbon steel column and discharge head, 304/316L stainless steel bowl, impeller, and shaft. This combination provides good corrosion resistance and economy.

  • Aggressive condensate (low pH, high chlorides from cooling water contamination, temperature >150°C): Full 316L stainless steel wetted parts (column, bowl, impeller, shaft). 316L offers better high‑temperature chloride resistance.

  • Very high purity condensate (boiler feed quality): 316L stainless steel to avoid any iron oxide contamination entering the boiler.

All materials supplied with EN 10204 Type 3.1 certification and full traceability.

Mechanical Seals – API 682 for Hot Condensate

The mechanical seal is located in the discharge head above grade, not submerged. Hot condensate at up to 200°C requires a seal plan that prevents flashing and maintains lubrication.

Seal ArrangementAPI 682 PlanSuitability for Condensate Recovery
Single seal with recirculation coolerPlan 23Recommended – external cooler continuously circulates cooled fluid through the seal chamber, preventing flashing and keeping seal faces cool
Single seal with external flushPlan 32Acceptable – clean external water (e.g., treated water) injected into seal chamber to cool and clean
Single seal with cooled flush from dischargePlan 21Alternate – takes hot water from pump discharge, passes through cooler, then into seal chamber
Dual pressurised (Arrangement 3)Plan 53BFor zero emissions (not typical for condensate)
Tandem seal (Arrangement 2)Plan 52For critical applications where any leakage is unacceptable

Plan 23 is the industry standard for high temperature water/condensate services. A closed loop recirculates fluid from the seal chamber through an external cooler (air or water cooled) and returns cooled fluid to the seal. The seal chamber is always filled with cool, liquid‑phase water, preventing flashing.

Recommended seal faces: Silicon carbide vs. carbon (good for water) or silicon carbide vs. silicon carbide (for higher reliability). Elastomers: Viton (FKM) up to 200°C; Kalrez for extended life.

For very high temperature (>180°C), consider a steam quench (Plan 62) added to Plan 23 to prevent ice formation on the atmosphere side if cold ambient conditions cause condensation.

NPSH and Suction for Condensate Pits

Condensate at the collection point is often near its saturation temperature (90‑100°C). Without adequate NPSH, cavitation will occur, destroying the pump. The VS2 design is specifically chosen for this challenge.

  • Submerged impeller – The pump bowl is placed below the minimum condensate level, providing positive NPSH from the liquid column. NPSHa = atmospheric pressure + (height of liquid above impeller) – (vapour pressure). The vapour pressure is near atmospheric, so the liquid column of 1‑3 metres provides enough NPSH margin.

  • Low NPSH first‑stage hydraulics – Optimised impeller inlet design reduces NPSH required (NPSHr) to ≤ 2 m.

  • Double suction first‑stage impeller (optional) – Further reduces NPSHr by 30‑40% when NPSHa is extremely limited.

  • Ensure minimum submergence – The manufacturer specifies a minimum liquid level above the suction bell to prevent vortexing and air ingestion.

Condensate Recovery System Considerations

  • Intermittent operation – Condensate pumps often start and stop based on pit level. The pump must be capable of frequent starts, with a motor rated for such duty. The VS2 design with surface motor and flexible shaft is suitable for intermittent service.

  • Thermal expansion – The column must allow for thermal expansion when handling hot condensate. The discharge head is designed to accommodate shaft and column growth.

  • Flash steam handling – The pit may contain flash steam. The pump and motor should be protected from prolonged steam exposure (shrouded motor, drainage, etc.).

  • Low flow protection – During periods of very low condensate flow, the pump may run below minimum continuous stable flow. Provide a recirculation line (bypass to pit) to maintain minimum flow and prevent overheating.

Applications for Condensate Recovery Pump

Industry / SettingSpecific Service
Power plants (conventional / combined cycle)Condensate extraction from condenser hotwell; low pressure heater drain return
Refineries & petrochemical plantsSteam trap condensate collection from process heating systems; condensate return from tracing
Industrial steam systems (paper, food, chemical)Condensate pumping from flash tanks, receiver tanks, and collection pits
District heatingCondensate return from heat exchangers to central plant
Cogeneration (CHP) plantsSteam turbine condensate recovery
Marine / shipBoiler condensate return from steam systems

Key Advantages of API 610 VS2 Condensate Recovery Pump

  • API 610 full compliance (VS2) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.

  • Vertical submerged design – Eliminates priming and low NPSH problems for hot condensate; no foot valve required.

  • Surface‑mounted driver – Motor remains dry, accessible for service, and protected from pit moisture.

  • Thermal expansion compensation – Column and shaft designed for high temperature up to 200°C.

  • Low NPSH capability – Submerged impeller and low‑NPSH hydraulics ensure cavitation‑free operation even with near‑saturation condensate.

  • High temperature materials – 316L stainless steel option for wetted parts resists high‑temperature corrosion.

  • API 682 Plan 23 ready – External cooler seal flushing protects seal faces in hot service.

  • Easy maintenance – Withdrawable rotor; no need to drain pit for seal or bearing inspection.

  • Proven in condensate service – Thousands of VS2 pumps operating in condensate recovery systems worldwide.

Quality Assurance & Testing

  • Hydrostatic test – Discharge head, column, and bowl tested at 1.5× design pressure.

  • Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).

  • Mechanical run test – 4 hours minimum continuous operation; vibration and bearing temperature recorded.

  • NPSH test – Optional, when specified (recommended for low NPSH condensate pits).

  • Impeller dynamic balancing – Grade G6.3 or better.

  • Material certification – EN 10204 3.1 for all pressure‑containing and wetted parts.

  • Hot test – For high‑temperature service, thermal cycle test available on request.

  • Third‑party inspection – Available (DNV, Lloyds, BV, SGS).

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (API 682 Plan 23 ready)1 set
Thrust bearing set (driver or discharge head)1 set
Intermediate line shaft bearing set (per column section)1 set per 2‑3 metres
Wear ring set (impeller + bowl)1 set
Impeller (for critical duty)1 set
Shaft (for critical duty)1
Gasket / O‑ring kit (full set)1 set

Get a Quote or Engineering Support

For detailed selection of the correct API 610 VS2 condensate recovery pump for your steam system or condensate return project – including flow, head, condensate temperature, pit depth (setting depth), NPSHa, material (carbon steel vs. stainless steel), and seal plan – please contact our engineering team.

Email: info@hyrig.com

Our API 610 VS2 condensate recovery pumps are specifically engineered for high‑temperature, low‑NPSH condensate return service – handling up to 200°C with submerged vertical turbine design, eliminating priming and cavitation. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with material options for carbon steel or stainless steel, and API 682 Plan 23 seal cooling for long, reliable service.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit