EN 1092-1 Face Form A vs Form B | Gasket & Sealing Logic

2026-11-18 11:43

EN 1092-1 Face Form A vs Form B

HYRIG can supply BS EN 1092-1 flanges in Form A (flat face) and Form B (raised face). This guide explains the structural difference, the gasket types required, and the mating rules that determine which face form belongs in your piping joint.

Key Facts

  • Form A: Flat face. Requires a full-face gasket that covers the entire flange face, including the bolt holes.
  • Form B: Raised face. The raised area concentrates bolt load onto a smaller gasket area. Requires a confined gasket (spiral wound or ring).
  • Mating rule: Form A and Form B should not be mated together. The raised face of Form B will not seal correctly against the flat face of Form A.
  • RFQ rule: Always specify the face form (A or B). Omitting it is a common cause of gasket selection errors.

Key Specifications

FeatureForm A (Flat Face)Form B (Raised Face)
Face GeometryFlat, full surfaceRaised circular area
Gasket TypeFull-face gasket (sheet)Spiral wound, ring, or confined gasket
Bolt LoadDistributed over full faceConcentrated on raised area
Typical ApplicationCast iron or low-pressure steelHigh-pressure steel flanges
Mating CompatibilityFlat face onlyFlat face with recess, or raised face

Dimensions

DimensionStandard
Face Finish (Form B)125–250 AARH
Raised Face Height (f)Per EN 1092-1 table (typically 2–5 mm)
Gasket ID (Form B)Must sit within raised face diameter

Structure and Working Principle

A Form A flange has a completely flat face. When bolted, the gasket must cover the entire face, including the bolt holes, to prevent leakage. This design is common in low-pressure applications, or when mating to cast iron equipment where a raised face could crack the casting.

A Form B flange has a raised circular area on the face. The bolt load is concentrated on this raised area, which produces a higher seating stress on the gasket. This allows the use of smaller, confined gaskets (like spiral wound) and is the standard for high-pressure steel piping.

The mating rule matters. If you bolt a Form B (raised face) flange to a Form A (flat face) flange, the raised face creates a gap around the perimeter. The gasket cannot seal evenly, and the joint will leak. Always mate Form B with Form B, or Form A with Form A.

Cross-Reference and Replacement

When replacing or specifying an EN 1092-1 flange:

  1. Inspect the existing face: Is it flat (Form A) or raised (Form B)?
  2. Check the mating flange: The new flange must match the face form of the existing mating flange.
  3. Order the correct gasket: A full-face gasket for Form A; a spiral wound or confined gasket for Form B.
  4. Verify the raised face height: Do not assume it is the same across all pressure classes; check the EN 1092-1 table.

Applications

  • Form A: Low-pressure water lines, cast iron valve connections, and non-critical utility piping.
  • Form B: High-pressure steam, hydrocarbon process lines, and steel piping requiring confined gaskets.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Can I mate a Form A flange with a Form B flange?

No. The raised face of Form B will not seal correctly against the flat face of Form A. The gasket will not compress evenly, leading to leaks.

Q: What gasket is used with Form A?

A full-face gasket that covers the entire flange face, including the bolt holes.

Q: What gasket is used with Form B?

A spiral wound, ring, or confined gasket that sits within the raised face diameter.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, PN rating, and material.

Selection Support

To confirm the correct face form and gasket for your line, provide the existing flange face type, pressure rating, medium, and mating equipment. Our engineers will verify the specification.

Contact

For EN 1092-1 face form selection, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment