EN 1092-1 Type 11 vs Type 01 Flange | Weld Neck vs Plate

2026-11-17 19:28

EN 1092-1 Type 11 vs Type 01 Flange

HYRIG supplies both Type 11 weld-neck and Type 01 plate flanges to EN 1092-1. This guide explains the hub geometry, welding method, and pressure-rating limits that separate the two types, and why Type 11 is not just a longer Type 01.

Key Facts

  • Type 11: Weld-neck flange with a tapered hub. Bore matched to pipe ID. Butt-welded to the pipe. Used for high-pressure, high-temperature, and cyclic service.
  • Type 01: Plate flange. Flat plate with a bore, fillet-welded to the pipe. Limited to lower pressure ratings and less severe service.
  • ASME equivalence: Type 11 corresponds to the ASME weld-neck flange; Type 01 has no direct ASME equivalent.
  • RFQ pitfall: "Weld neck" alone is not enough. The type number (11 or 01) must be stated.

Key Specifications

FeatureType 11 Weld NeckType 01 Plate Flange
Hub geometryTapered hub transitions to pipe wallFlat plate, no hub
Weld typeButt weldFillet weld (two sides)
BoreMatched to pipe IDB1 bore, specified separately
Pressure ratingPN16–PN40 and aboveLower PN range; limited by plate thickness
Typical serviceHigh pressure, high temperature, cyclicLow pressure, utility, non-critical

Dimensions

DimensionStandard
Flange OD (D)EN 1092-1
Bolt circle (k)EN 1092-1
Hub diameter (A)Type 11 only
Neck thickness (S)Type 11 only
Bore (B1)Type 01

Structure and Working Principle

A Type 11 weld-neck flange has a tapered hub that extends from the flange ring to the pipe. The hub thickness matches the pipe wall at the weld end, and the bore is machined to match the pipe ID. The butt weld creates a full-penetration joint, and the tapered hub distributes the stress from the flange ring into the pipe wall. This makes Type 11 suitable for high-pressure, high-temperature, and cyclic service, where fatigue and stress concentration are concerns.

A Type 01 plate flange is a flat plate with a bore and bolt holes. It is slipped over the pipe and welded with two fillet welds (one on each side of the plate). The plate has no hub to distribute stress, so it is limited to lower pressure ratings and less severe service. It is economical and widely used in utility and low-pressure piping.

The distinction matters for procurement because “weld neck” and “plate” are not interchangeable descriptions. Type 11 is a specific EN 1092-1 type number; Type 01 is a different type number. An RFQ that says “weld neck flange, PN16” without a type number may receive a Type 11, but an RFQ that says “flange, PN16” may receive a Type 01.

Cross-Reference and Replacement

When replacing or specifying an EN 1092-1 flange:

  1. Identify the existing type: Look for the hub (Type 11) or confirm the plate construction (Type 01). The type number must be in the RFQ.
  2. Check the pressure rating: Type 01 is limited to lower PN ratings; do not substitute Type 01 for Type 11 in high-pressure or cyclic service.
  3. Confirm the bore: Type 11 bore is matched to the pipe ID; Type 01 bore (B1) is specified separately and may differ.
  4. Do not rely on “weld neck” alone: State Type 11 explicitly; “weld neck” is a description, not a type number.

Applications

  • Type 11: High-pressure steam, hydrocarbon process lines, cyclic service, and critical piping where stress distribution matters.
  • Type 01: Utility water, low-pressure process lines, and non-critical connections where cost and simplicity are priorities.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Is Type 11 the same as a weld-neck flange?

Yes, Type 11 is the EN 1092-1 designation for the weld-neck flange. But “weld neck” alone is not enough in an RFQ; the type number should be stated.

Q: Does Type 01 have an ASME equivalent?

Type 01 has no direct ASME B16.5 equivalent. The closest functional analogue is a slip-on flange, but the dimensions and welding details differ.

Q: Can Type 01 be used at PN40?

Type 01 plate flanges are generally limited to lower PN ratings. Confirm the allowable pressure at temperature from the EN 1092-1 table for the specific plate thickness and material.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, PN rating, and material.

Selection Support

To choose between Type 11 and Type 01, provide the pressure rating, temperature, pipe size, and service severity. Our engineers will confirm the correct type and bore.

Contact

For EN 1092-1 Type 11 vs Type 01 selection, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment