EN 1092-1 vs ASME B16.5 Flange | Interchangeability & Bolt Circle

2026-11-17 19:27

EN 1092-1 vs ASME B16.5 Flange

HYRIG supplies flanges to both EN 1092-1 and ASME B16.5. This guide explains why the two standards cannot be bolted together, using DN 150 / NPS 6 as a reference, and what to verify when replacing one with the other.

Key Facts

  • Standard basis: EN 1092-1 uses DN and PN; ASME B16.5 uses NPS and Class.
  • Dimensional system: EN uses metric (mm); ASME uses inch-based dimensions with metric conversion.
  • Bolt pattern: EN uses metric bolt sizes (M16, M20); ASME uses imperial (5/8", 3/4").
  • Interchangeability: The two standards are not interchangeable. Flanges built to one cannot be bolted to the other.

Key Specifications

FeatureEN 1092-1 PN16ASME B16.5 Class 150
DN / NPS referenceDN 150NPS 6
Flange OD285 mm279.4 mm
Bolt circle240 mm241.3 mm
Bolt sizeM203/4"
Bolt hole22 mm22.4 mm
Flange thickness (WN)22 mm22.4 mm

Dimensions

DimensionStandard
EN 1092-1 dimensionsDN and PN
ASME B16.5 dimensionsNPS and Class
Bolt sizingEN: metric; ASME: imperial
Face formEN: Form A/B; ASME: RF/FF/RTJ

Structure and Working Principle

The two standards serve the same function but define completely different dimensional systems. EN 1092-1 is a metric standard: DN for size, PN for pressure rating, and metric bolt sizes. ASME B16.5 is an inch-based standard: NPS for size, Class for pressure rating, and imperial bolt sizes.

The apparent closeness at equivalent sizes is misleading. At DN 150 / NPS 6, the EN flange OD is 285 mm and the ASME OD is 279.4 mm; the bolt circles are 240 mm and 241.3 mm respectively. The bolt holes differ by fractions of a millimeter, and the bolt threads are metric vs UNC. Attempting to bolt them together risks misalignment, uneven gasket compression, and leaks.

The pressure-rating methods also differ. ASME B16.5 uses material-group pressure-temperature tables; EN 1092-1 uses PN numbers with separate material-group derating tables. A PN16 flange and a Class 150 flange do not have the same allowable pressure at temperature, even though they are often treated as rough equivalents in early project discussions.

Cross-Reference and Replacement

When replacing an EN 1092-1 flange with an ASME B16.5 flange, or vice versa:

  1. Confirm the governing standard: Check the piping class or project specification. Do not substitute across standards without engineering approval.
  2. Measure the bolt circle and bolt size: Even if the OD looks compatible, the bolt pattern and thread may differ.
  3. Check the gasket and face form: EN Form A/B and ASME RF/FF/RTJ are not directly interchangeable; the gasket and bolting torque must match the face form.
  4. Verify the pressure-temperature rating: Do not treat PN16 and Class 150 as equivalent. Check the allowable pressure at operating temperature from the correct standard table.

Applications

  • EN 1092-1: European-designed plant piping, skids built to DIN/EN standards, projects specifying PN ratings.
  • ASME B16.5: American-designed plant piping, oil and gas projects specifying Class ratings, equipment with ASME flanges.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Can a PN 16 flange be bolted to a Class 150 flange?

No. The bolt circle, bolt hole diameter, and bolt thread differ. They cannot be bolted together.

Q: Is DN 150 the same as NPS 6?

DN 150 and NPS 6 are similar nominal sizes, but the flange dimensions and bolt patterns are not interchangeable.

Q: Which standard is used in Europe?

EN 1092-1 is the European standard for steel pipe flanges. ASME B16.5 is used in the Americas and in many international oil and gas projects.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, rating, material, and documentation.

Selection Support

To confirm whether an EN 1092-1 or ASME B16.5 flange is required for your line, provide the piping class, existing flange dimensions, bolt pattern, and face form. Our engineers will verify the standard basis.

Contact

For help selecting between EN 1092-1 and ASME B16.5 flanges, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment