A glycol circulation pump is the heart of a glycol dehydration unit (TEG or MEG) or a glycol‑based heat transfer loop. It continuously pumps lean glycol from the reboiler to the absorber (contactor) or circulates glycol through a closed loop. The pump must operate 24/7/365 at moderate to high temperatures (typically 80-150°C) with corrosion‑prone glycol that degrades over time. Our API 610 OH2 centrifugal pump is specifically engineered for demanding glycol circulation duty. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches glycol circulation requirements because:
OH2 provides easy maintenance without disturbing piping – critical for continuous processes where downtime is costly.
Back pull‑out allows seal and bearing inspection while casing stays in line.
High temperature capability (up to 150°C) is accommodated with optional centerline support and cooling.
Corrosion resistant materials (316SS, duplex) are standard.
Long, uninterrupted operation – robust API bearings and seal plans ensure high MTBR.
Why API 610 OH2 for glycol circulation duty?
Continuous duty reliability – Glycol circulation pumps often run for years between overhauls. API 610 heavy duty construction, oil mist lubrication option, and vibration monitoring ensure high availability.
Corrosion resistance – Glycol degrades to organic acids (formic, acetic, glycolic). Wetted parts require 316SS minimum; duplex or Alloy 20 for higher temperatures or acidic glycol.
High temperature capability – Lean glycol at reboiler outlet is typically 120-150°C. Centerline support (not foot‑mounted) prevents thermal distortion. Bearing housing cooling (fan or water) and API 682 Plan 23 (cooled recirculation) seal plan extend component life.
Low NPSH – The reboiler or surge drum may provide limited NPSHa (often 2-4 m). Inducer reduces NPSHr to below 1 m, preventing cavitation and noise.
High efficiency – Circulation pumps run continuously; even a few percent efficiency gain saves significant energy over years.
Standardized hydraulics – Flow ranges from 10 to 2000 m³/h, heads from 50 to 250 m, cover most TEG/MEG circulation duties.
Key design features for glycol circulation service
Materials – Casing: 316SS (CF8M/CF3M) or duplex (CD4MCu). Impeller: 316SS or 17-4PH. Shaft: 316SS or duplex. Wear rings: 17-4PH H1150 or Stellite. Gaskets: PTFE.
Temperature management – Specify centerline support for all glycol circulation pumps with operating temperature >100°C. For >120°C, add bearing housing cooling (fan or water jacket) and Plan 23 seal (cooled product recirculation).
Inducer – Recommended if NPSHa is less than 3 m to ensure cavitation‑free operation.
Impeller – Closed, double‑volute casing for large flows to reduce radial load. Trim to exact duty point for optimum efficiency.
Sealing – API 682 Plan 11 (recirculation from discharge) standard for clean glycol. Plan 23 (cooled recirculation) for glycol >100°C. For dirty glycol containing solids (corrosion products), Plan 31 (cyclone) or Plan 32 (external flush). Double seals with Plan 53A if zero emissions required.
Bearings – Anti‑friction, oil bath or pure oil mist (preferred for continuous operation). Optional temperature sensors RTD/thermocouple.
Casing drain – Full size drain for complete removal of glycol during maintenance (prevents freezing in cold climates).
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 10 – 2000 m³/h |
| Head | 50 – 250 m |
| Temperature | Up to 150°C |
| Pressure rating | Up to 25 bar (higher on request) |
| NPSHr (with inducer) | As low as 0.5 m |
| Speeds | 1450 / 2900 / 3600 rpm |
| Efficiency | Up to 85% |
Typical glycol circulation applications
TEG contactor circulation – Natural gas dehydration (lean TEG from reboiler to absorber).
MEG regeneration loops – Lean MEG circulation through reboiler and back to injection.
Glycol cooling loops – Pumping glycol through heat exchangers and users.
Offshore platform glycol circuits – Compact, corrosion resistant designs.
Air handling / HVAC – Glycol as freeze protection fluid.
Why choose our API 610 OH2 glycol circulation pump?
Full API 610 compliance – Performance test, NPSH test (inducer), 4-hour mechanical run test.
Corrosion resistant – 316SS as minimum; full stainless steel wetted parts.
High temperature design – Centerline support, Plan 23 seals, cooled bearings.
Low NPSH – Inducer option ensures stable operation from glycol surge drums.
Long MTBR – Designed for 3+ years continuous service with proper maintenance.
Short lead time – Standard 316SS circulation pumps (8-12 weeks); custom options available.
Global spare parts support – Impellers, shafts, seal cartridges, bearings, casing covers shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test with vibration and bearing temperature monitoring.
Hydrostatic test of casing.
Material traceability EN 10204 3.1 / 3.2.
PMI for alloy components.
NDE – MT, PT, UT as required.
How to specify your glycol circulation pump
Please provide: flow (m³/h), head (m), operating temperature (°C), NPSHa (m), glycol type (TEG or MEG), concentration, presence of solids / degradation products, required material (316SS / duplex / Alloy 20), and continuous or intermittent service. We will recommend inducer (yes/no), impeller trim, seal plan (11/23/31), bearing cooling, and driver details.
Contact us
For a quotation or technical discussion on glycol circulation pumps (API 610 OH2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.