KT20000 Casing Tong: Professional Maintenance Guide – Extend Equipment Life & Ensure Operational Stability

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
KT20000 casing tong professional maintenance guide. Daily after-use (10 min): clean with petroleum-based cleaner, blow debris with ≤0.5MPa air, lubricate 8 key points (idler bearings, pinion bearings, roller cups, clutch bearing, shift shaft, door cam, door stop, jaw cam, locating pins) using multi-purpose grease. Check bolts (M16≥45N·m, M20≥80N·m), hoses, jaws, safety door. Periodic: torque gauge calibration (≤±2%) every 50 hrs; change hydraulic oil and filters every 200 hrs; inspect gears and replace seals every 500 hrs. Extreme cold (-40°C): use low-temp grease and ISO VG32 hydraulic oil, preheat 10 min. Sour gas fields: anti-sulfur seals. Offshore: anti-corrosion coating. Maintain logbook. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

Subtitle: Daily Maintenance + Periodic Servicing + Special Protection – Comprehensive Care to Reduce Operating Costs


I. Daily Maintenance: After Each Operation (10 Minutes)

(A) Cleaning – Remove Contaminants to Prevent Wear

  • Surface cleaning: Use petroleum-based cleaner (or neutral detergent) with clean cloth to wipe tong body, safety door, hydraulic hoses, and fittings. Remove oil, mud, and drilling fluid residue. Pay special attention to jaw gripping surfaces, gearbox observation window, and torque gauge face (ensure clear reading).

  • Gap cleaning: Use compressed air (≤0.5 MPa) to blow out safety door gaps, jaw roller clearances, and hydraulic fitting interfaces. Prevent debris accumulation that could cause sticking or seal failure.

  • Hydraulic system cleaning: Check hydraulic tank fill port and air breather. Remove surface dust. Ensure sealing cap is tight to prevent contaminants from entering tank.

(B) Lubrication – Precise Greasing to Reduce Friction

Core component lubrication standards (use manufacturer-recommended multi-purpose bearing grease suitable for -40°C to 60°C):

ComponentLubrication MethodQuantity / FrequencyKey Notes
Rotating idler bearingsGrease gun via grease fitting4 strokes after each useEven grease coverage; avoid excess contaminating jaws
Pinion idler bearingsGrease gun via grease fitting4 strokes after each useRotate gear after greasing to ensure penetration
Roller cup bearings (upper & lower)Grease gun via grease fitting3 strokes each after each useFill bearing gaps; no dryness
Clutch bearingGrease gun via grease fitting1 stroke after each useLocated on bottom of tong; rotate clutch lightly after greasing
Shift shaftGrease gun to shaft sleeve1 stroke after each useEnsure full lubrication of sleeve/shaft contact for smooth shifting
Door lock camGrease gun via grease fitting2 strokes after each useCover cam and locking mechanism; prevent door sticking
Door stop assemblyApply general-purpose oilFull coverage after each useEven oil on spring and piston surfaces
Jaw cam surfaceApply greaseLiberal coat after each useReplenish before operation; ensure smooth jaw action and reduce casing wear
Locating pinsApply anti-rust greaseThin coat after each usePrevent rust that could cause difficult insertion/removal

Lubrication best practices:

  • Clean grease fitting before greasing to prevent contaminant ingress.

  • Apply slowly until small amount of fresh grease exits (expelling old grease). Avoid over-greasing which can cause overheating.

  • Wipe away excess grease after lubrication to prevent dust attraction.

(C) Inspection & Tightening – Identify Hazards, Ensure Secure Connections

  • Bolt & fitting check: Spot-check tong body bolts, hydraulic hose fittings, and suspension system bolts with a wrench. Ensure no looseness (torque per manufacturer: M16 bolts ≥45 N·m, M20 bolts ≥80 N·m).

  • Core component inspection:

    • Jaws: Rollers free of cracks or wear (wear ≤1 mm). Jaw body no deformation. Mounting bolts secure.

    • Locating pins: No deformation, cracks, or rust. Insert/remove smoothly without sticking.

    • Hydraulic hoses: No bulges, damage, or aging (no surface cracking). Fittings sealed with no leaks.

    • Safety door: Locking mechanism reliable. Door opens/closes smoothly with no looseness or unusual noise.


II. Periodic Maintenance – Graded by Operating Hours

(A) Short-Term Service (Every 50 Operating Hours)

  • Torque gauge calibration: Verify gauge reading using a calibrated torque wrench. Error ≤±2%. If out of tolerance, adjust or contact factory for calibration.

  • Hydraulic system check:

    • Check oil level; top up to mark if below 1/3 of scale. Use manufacturer-specified hydraulic oil.

    • Inspect hydraulic filter element. Replace if excessive debris visible through filter sight glass.

    • Test hydraulic system pressure: Run unit unloaded. Idle pressure ≤200 PSI. Load pressure stable at 18 MPa with no fluctuation.

  • Shift mechanism inspection: Remove clutch inspection plate. Check shift shaft and fork connection – secure, no wear. Apply grease and reassemble.

(B) Medium-Term Service (Every 200 Operating Hours)

  • Hydraulic oil change:

    • Drain old oil. Clean tank interior with clean cloth (do not use synthetic fiber cloth).

    • Replace hydraulic filter element and return filter element. Ensure good seal when installing new filters.

    • Fill with new hydraulic oil to mark. Run unit for 5 minutes, then recheck oil level and top up.

  • Brake belt adjustment: Check brake belt wear. If gap between brake belt and cage plate exceeds 0.5 mm, tighten adjustment bolt clockwise until proper friction is restored for normal jaw cam action.

  • Bearing condition check: Assess bearings by sound and temperature (operating temperature ≤70°C). If unusual noise or overheating, disassemble for inspection or replacement.

(C) Long-Term Service (Every 500 Operating Hours / Annually)

  • Core component disassembly inspection:

    • Remove safety door. Check door rollers and bushings for wear. Replace aged parts.

    • Remove jaws. Check roller and cam surface wear. Replace jaws or rollers if wear exceeds limits.

    • Open gearbox top observation window. Check gear engagement – no severe wear or broken teeth. Apply grease to gear surfaces.

  • Seal replacement: Replace hydraulic hose fitting seals, tank gaskets, and observation window sealing strips. Prevent leaks.

  • Full performance test: Start unit and test forward/reverse rotation, high/low gear shifting, torque output accuracy. Ensure all performance meets factory standards.


III. Special Condition Maintenance – Targeted Protection for Complex Environments

(A) Extreme Cold Operations (Ambient Temperature ≤ -10°C)

  • Lubrication adjustment: Use low-temperature grease (freezing point ≤ -45°C). Pre-heat core bearings by running unit unloaded for 10 minutes before operation.

  • Hydraulic oil selection: Use low-temperature hydraulic oil (ISO VG32) to prevent viscosity increase that could reduce power.

  • Freeze protection: Drain residual moisture from hydraulic system after operation (if present). Store unit indoors or cover with insulated blanket to prevent freeze cracking.

(B) High-Sour Gas Fields (H₂S Environment)

  • Material upgrade: Use anti-sulfur seals and gaskets (specially formulated elastomers resistant to H₂S attack). Replace standard seals with anti-sulfur versions.

  • Inspection frequency: Double inspection intervals for hoses and seals. Replace at first sign of swelling or hardening.

  • Post-operation: Rinse external surfaces with fresh water to remove corrosive residue.

(C) Offshore Platform Operations

  • Corrosion protection: Apply marine-grade anti-corrosion coating to exposed metal surfaces. Inspect monthly for paint damage and touch up immediately.

  • Salt spray management: Clean electrical connectors and torque gauge with dielectric cleaner. Cover sensitive components when not in use.

  • Vibration resistance: Check all bolt torques weekly due to continuous platform vibration.


IV. Maintenance Tools & Recommended Spare Parts

Required Tools

ToolSpecification
Grease gunManual or pneumatic
Torque wrenchRange 0-200 N·m
Hex key setMetric
Combination wrench set8-24 mm
Oil filter wrenchFor hydraulic filter
Compressed air gun≤0.5 MPa
Cleaning clothsLint-free
Parts washerFor cleaning components

Recommended Spare Parts (Keep on Site)

PartQuantityNotes
Jaw assemblies (various sizes)2 sets per sizeFor 7″-20″ casing
Rollers & roller shafts1 setFor jaw and door
Locating pins2 each (make-up & break-out)
Brake belt1 piece
Seal kit (full set)1 kitIncludes O-rings, Y-rings, dust seals
Hydraulic hoses (1″ & 1-1/4″)2 each
Hydraulic filter element2 pieces
Low-temp grease (for extreme cold)1 cartridgeIf operating below -10°C
Anti-sulfur seal kit1 kitFor sour gas fields

V. Maintenance Records

Maintain a logbook for each KT20000 casing tong. Record:

  • Date and operating hours

  • Daily maintenance performed (cleaning, lubrication, inspections)

  • Periodic service completed (50/200/500 hour)

  • Any abnormal findings and corrective actions

  • Parts replaced (with part numbers)

  • Torque gauge calibration dates and results

  • Hydraulic oil change dates

A well-kept log helps predict wear, schedule downtime, and extend equipment life.


Contact Us

For maintenance training, genuine spare parts, or technical support, please contact us:

info@hyrig.com

We provide comprehensive after-sales service for all TEDA casing power tongs, including the KT20000.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit