OH2 Pump – API 610 Overhung Centrifugal Pump

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Conatct For Details
DetailReview(0)Additional

Product Overview

The OH2 pump is an overhung, centerline-mounted, single-stage centrifugal pump fully compliant with API 610 11th/12th edition (ISO 13709) standards. The "OH" designation stands for Overhung – meaning the impeller is mounted on the end of a shaft that overhangs its bearing support, with no bearing between the impeller and the shaft end. The "2" suffix specifies a centerline-mounted foot arrangement, which keeps the pump centerline at the same elevation as the mounting feet to accommodate thermal expansion.

This configuration is the most widely used API 610 pump type for general refinery, petrochemical, and industrial process services. OH2 pumps offer a compact footprint, easy access to mechanical seals and bearings, and robust performance across a broad range of temperatures, pressures, and fluid types.

Key Specifications (OH2 Pump Series)

ParameterRange
Flow rateUp to 720 m³/h (3,170 gpm) – typical; larger designs available
HeadUp to 255 m (837 ft) – single stage; higher with special hydraulics
Pressure ratingUp to 6.4 MPa (64 bar / 928 psi)
Temperature range–80°C to +400°C (–112°F to +752°F)
Speed1,450 / 2,950 rpm (50 Hz) or 1,750 / 3,550 rpm (60 Hz)
Maximum casing pressureUp to 10 MPa (100 bar) for special designs
Efficiency55% – 85% depending on hydraulic size
NPSHrOptimized per size; inducer available for low NPSHa

API 610 OH2 Construction Features

Overhung Design

The impeller is mounted at the non-drive end of the shaft, with the bearing housing located immediately behind the impeller. No inboard bearing exists – the shaft is supported only by bearings at the drive end. This simplifies the pump, reduces parts count, and shortens the overall length.

Centerline Mounting

The pump feet are cast integrally with the casing and are positioned on the horizontal centerline of the shaft. This allows the casing to expand uniformly when handling hot fluids, keeping the shaft aligned with the driver and preventing misalignment due to thermal growth.

Bearing Housing

A heavy-duty, finned bearing housing supports the shaft. Bearings are lubricated by oil bath (standard) or forced oil circulation (optional). Bearing life exceeds API 610 minimum L10 of 25,000 hours. Cooling coils or fins dissipate heat from the bearing housing when handling high-temperature fluids (>150°C).

Shaft and Impeller

The shaft is a one-piece forging with generous diameter to minimize deflection. The overhung impeller is keyed, dynamically balanced, and secured with a cap screw and locking washer. Wear rings (replaceable) are fitted on both casing and impeller to preserve clearances and efficiency.

Casing

Radially split, single-stage, centerline-mounted casing. Suction and discharge flanges are integral with the casing and face vertically upward (top suction / top discharge) – the standard OH2 nozzle arrangement. This provides easy piping alignment and allows removal of the rotor without disconnecting piping.

Baseplate

Heavy-duty steel baseplate, grouted, with drip lip and drain connection. The driver (electric motor or turbine) mounts on the same baseplate. Coupling is a flexible spacer type, allowing seal and bearing maintenance without moving the driver.

Materials (API 610 Table H)

ComponentCarbon Steel (C-6)316L SS (S-8)Duplex (D-1/D-2)
CasingWCB / LCCCF3M (316L)CD4MCu / 2205
ImpellerWCB / LCCCF3M (316L)CD4MCu / 2205
Shaft4140 / 2Cr134140 (coated) or 316 SSDuplex SS
Wear ringsHardened 4140316 SS + StelliteDuplex + hard facing
GasketsSpiral wound (graphite filled)Spiral wound (graphite filled)Spiral wound / PTFE

S-8 (316L stainless steel) is the most common selection for corrosive services including amine, sour water, caustic, and many chemical streams. C-6 (carbon steel) is used for clean hydrocarbons, hot oil, and BFW. Duplex (D-1/D-2) is specified for chloride-containing fluids or high H₂S environments with NACE MR0175 compliance.

Mechanical Seals – API 682 Compliance

OH2 pumps are equipped with API 682 mechanical seals. The seal chamber is cast integrally with the casing and sized to accommodate all API 682 seal types (A, B, C) and arrangements (1, 2, 3) without modification.

ServiceRecommended Seal TypeAPI PlanNotes
Clean hydrocarbon (diesel, gasoline)Single cartridge (Type A)Plan 11 / 21Standard self-flush
High-temperature oil (>200°C)Single bellows (Type B)Plan 21 + coolingPlan 23 preferred for >250°C
Sour water / rich amineDual pressurized (Arr. 3)Plan 53BH₂S containment
Lean amineDual or tandemPlan 52 / 53AEmission control
Hot water / BFWSingle (Type B) with coolingPlan 23Recirculation cooler
Caustic / amineDual (Arr. 2 or 3)Plan 52 / 53BCorrosion resistant faces (SiC/SiC)

Typical Applications for OH2 Pumps

IndustryApplicationMedium Examples
RefiningCrude transfer, product rundown, refluxCrude oil, diesel, kerosene, naphtha, gasoline
RefiningAmine circulationLean amine, rich amine, MDEA, MEA
RefiningSour waterSour water (H₂S/NH₃)
PetrochemicalChemical feed, transferAcids, caustics, solvents, monomers
Power generationBoiler feed boosterBFW, condensate
Gas processingGlycol circulationTEG, MEG
Water / wastewaterRaw water, service waterFresh water, cooling water

OH2 vs Other API 610 Types

Pump TypeConfigurationBest UseAdvantages
OH2Overhung, centerline, single stageGeneral refinery/petrochem duties up to moderate headCompact, low cost, easy maintenance, thermal stability
OH1Overhung, foot mountedLow temperature, clean servicesNon-API for many specs; not centerline mounted
OH3Vertical, in-line, overhungSpace-limited, low NPSHVertical mounting
OH4Rigid coupled, verticalSmall capacityCompact motor-pump unit
BB2Between bearings, single stageHigh flow, moderate headHigher flow capacity
BB3Between bearings, axially split, multistageHigh head, high pressureFor head >250 m
BB5Barrel, radially split, multistageVery high pressureUp to 500 bar

The OH2 pump is the most widely specified API 610 type – it meets the vast majority of refinery and petrochemical pumping requirements (excluding very high head or very high pressure services).

Performance Characteristics

  • Head-capacity curve: Stable, continuously rising to shut-off – essential for parallel pump operation

  • Best Efficiency Point (BEP): Typically at 70-90% of rated flow for standard selections

  • Minimum flow: Usually 25-30% of BEP flow (continuous recirculation or automatic recirculation valve recommended)

  • NPSHr: Approximately 2-6 m for standard impellers; inducer reduces NPSHr by 40-60%

Maintenance Features

  • Back pull-out design – The complete rotating assembly (bearing housing, bearing bracket, shaft, impeller, seal chamber) can be removed from the casing without disconnecting piping.

  • Spacer coupling – Allows removal of the rotating assembly without moving the driver.

  • Cartridge mechanical seals – Replaceable as a unit without disassembling the pump.

  • Replaceable wear rings – Restore hydraulic clearances without replacing the casing or impeller.

Quality Assurance and Testing (Per API 610)

  • Hydrostatic test: 1.5x design pressure

  • Performance test: Water, at rated speed (Grade 1 or 2)

  • Mechanical run test: Minimum 4 hours

  • NPSH test: Optional per specification

  • Material certification: EN 10204 3.1 (full traceability)

  • NDE: MPI, dye penetrant, or radiography per API 610

Why Choose Our OH2 Pump?

  • Full API 610 11th/12th edition compliance – design life 20 years, 3-year continuous service

  • Centerline mounting – maintains alignment during thermal cycling; essential for hot services (>150°C)

  • Broad hydraulic cover – single pump series covers most refinery duties

  • Minimum spare parts inventory – common bearing frames and seal chambers across multiple pump sizes

  • API 682 ready – accepts any seal arrangement without modification

  • Back pull-out design – reduces maintenance downtime by up to 50%

  • Material flexibility – carbon steel, 316L SS, duplex, and all API 610 Table H classes

  • Global installed base – thousands of units in reliable service across refineries, petrochemical plants, and power stations

Recommended Spare Parts

ComponentRecommended Quantity
Mechanical seal cartridge1 set per pump
Bearing set (radial + thrust)1 set
Wear ring set (casing + impeller)1 set
Gasket / O-ring kit1 set per pump
Shaft (critical units)1 per 3 pumps

Get a Quote or Engineering Support

For detailed selection of the correct OH2 pump for your process duty – including hydraulic sizing, material selection (C-6, S-8, D-1/D-2), seal plan (API 682), NPSH verification, and complete API 610 data sheet – please contact our engineering team.

Email: info@hyrig.com

*Our engineers support refinery, petrochemical, and industrial projects worldwide with reliable API 610 OH2 pumping solutions for every moderate-head process service.*


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit