A propane pump must handle liquefied propane (a high vapour pressure hydrocarbon) safely, with zero leakage and often under tight NPSH (net positive suction head) conditions. Our API 610 VS6 submerged in-tank pump is specifically engineered for propane and commercial LPG services. This design fully complies with API 610 11th/12th edition (ISO 13709) for vertical submerged pumps.
Structure match check: API 610 VS6 is defined as a vertical, single-casing, submerged pump where the driver and hydraulics are fully immersed in the pumped liquid. There is no external shaft seal. This matches exactly the requirements for propane in-tank pumping: zero leakage, intrinsic safety, and low NPSH.
Why API 610 VS6 for propane duty?
Zero dynamic seal – Eliminates mechanical shaft seals completely. The motor runs submerged in oxygen-free propane, so there is no external leakage path. Meets strict environmental regulations (LDAR, EPA, EU Seveso).
Intrinsically safe – Submerged motor operates inside propane vapor-free liquid. No explosion risk, no external purging required. ATEX / IECEx Zone 0 ready.
Top-pull maintenance – The entire pump assembly (hydraulics + motor) can be withdrawn through the tank top nozzle without emptying or degassing the tank. Downtime reduced by over 70% compared to external pumps.
Low NPSH capability – Optional first-stage inducer reduces NPSHr to below 1 m, preventing cavitation and vapour lock – critical for high vapour pressure propane.
Wide performance range – Handles pure propane, commercial LPG (propane/butane mixes), and even high-propane blends.
High reliability – No seal wear, no fugitive emissions, no external mechanical failures.
Key design features (API 610 VS6 for propane)
Single casing construction – Outer can withstand tank pressure (up to 25 bar / 2.5 MPa). Inner diffuser casing contains multistage impellers.
Submerged permanent magnet synchronous motor (PMSM) – Self-cooled by liquid propane. High efficiency (over 85% at design point).
Bearings – Carbon-graphite or ceramic-lined, lubricated by propane. No external lube system.
Inducer on first stage – Prevents cavitation at low NPSHa typical in bullet tanks.
Wetted materials – Ductile iron or carbon steel for clean propane. Stainless steel 316 for sour propane (H₂S) or higher corrosion resistance. NACE MR0175 optional.
Temperature range – -45°C to +50°C (suitable for winter propane storage and summer ambient).
Discharge pressure – Up to 2.5 MPa (25 bar) standard; higher on request.
Flow range – 5 to 800 m³/h.
Head range – Up to 600 m (multistage design).
Typical applications
Propane bullet tanks – Mounded or above-ground pressurized vessels.
Spherical propane storage – High-pressure spheres in terminals.
Propane railcar / truck unloading – Pumping from transport tanks into storage.
LPG peak-shaving plants – Transfer propane to vaporizers during cold weather.
Refinery propane feed – To alkylation units or propane dehydrogenation (PDH).
Propane export / import terminals – Ship loading/unloading where in-tank pumps are required.
Why choose our API 610 VS6 propane pump?
Full API 610 compliance – Type VS6 verified per standard. Performance test, NPSH test, mechanical run test included.
Zero leakage – No mechanical seal, no packing, no fugitive emissions – best available technology (BAT) for propane.
Low NPSHr – Inducer option allows operation at less than 1 m NPSHa, preventing pump cavitation damage.
Easy installation – Complete assembly supplied with top flange ready to bolt to tank nozzle.
Short lead time – Standard sizes (e.g., 6”, 8”, 10” discharge) available ex-stock; custom hydraulics 8-12 weeks.
Global spare parts support – Impellers, inducer, bearings, motor stator, and complete replacement cartridges shipped worldwide.
Lower total cost – Competitive initial price plus zero seal maintenance and long MTBR.
Quality assurance
ISO 9001:2015 certified manufacturing.
API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.
NPSH test with inducer (if specified) to verify cavitation performance.
Hydrostatic test of outer can and pressure boundary.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT, UT as required.
How to specify your propane pump
Please provide: flow (m³/h), head (m), operating temperature (°C), tank pressure (bar or MPa), NPSHa available (m), propane purity (pure, commercial LPG, or H₂S content), and tank type (bullet, sphere, etc.). We will recommend pump size, stage count, inducer (yes/no), material class, and motor rating.
Contact us
For a quotation or technical discussion on propane pumps (API 610 VS6) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.