A butane pump must handle liquefied butane (a hydrocarbon with moderate vapour pressure, boiling point approximately -1°C) safely, with zero leakage and reliable operation from pressurized storage. Our API 610 VS6 submerged in-tank pump is specifically engineered for butane, commercial LPG, and high-butane blends. This design fully complies with API 610 11th/12th edition (ISO 13709) for vertical submerged pumps.
Structure match check: API 610 VS6 is defined as a vertical, single-casing, submerged pump where the driver and hydraulics are fully immersed in the pumped liquid. There is no external shaft seal. This matches exactly the requirements for butane in-tank pumping: zero leakage, intrinsic safety, and low NPSH (especially important for winter operation or when tank pressure is low).
Why API 610 VS6 for butane duty?
Zero dynamic seal – Eliminates mechanical shaft seals completely. The motor runs submerged in oxygen-free butane, so there is no external leakage path. Meets strict environmental regulations (LDAR, EPA, EU Seveso).
Intrinsically safe – Submerged motor operates inside butane liquid (vapour-free). No explosion risk, no external purging required. ATEX / IECEx Zone 0 ready.
Top-pull maintenance – The entire pump assembly (hydraulics + motor) can be withdrawn through the tank top nozzle without emptying or degassing the tank. Downtime reduced by over 70% compared to external pumps.
Low NPSH capability – Optional first-stage inducer reduces NPSHr to below 1 m, preventing cavitation and vapour lock – important for butane during cold weather or when tank pressure drops.
Wide performance range – Handles pure butane, commercial LPG (propane/butane mixes), and high-butane blends with varying vapour pressure.
High reliability – No seal wear, no fugitive emissions, no external mechanical failures.
Key design features (API 610 VS6 for butane)
Single casing construction – Outer can withstand tank pressure (up to 2.5 MPa / 25 bar standard; higher on request). Inner diffuser casing contains multistage impellers.
Submerged permanent magnet synchronous motor (PMSM) – Self-cooled by liquid butane. High efficiency (over 85% at design point).
Bearings – Carbon-graphite or ceramic-lined, lubricated by butane. No external lube system.
Inducer on first stage – Optional but recommended for butane if NPSHa is marginal (e.g., storage near vapour pressure).
Wetted materials – Ductile iron or carbon steel for clean butane. Stainless steel 316 for sour butane (H₂S) or higher corrosion resistance. NACE MR0175 optional.
Temperature range – -30°C to +50°C (butane typically stored near ambient, but can be colder in winter).
Discharge pressure – Up to 2.5 MPa (25 bar) standard; higher on request.
Flow range – 5 to 800 m³/h.
Head range – Up to 500 m (multistage design; butane typically requires lower head than propane due to lower vapour pressure).
Typical applications
Butane bullet tanks – Mounded or above-ground pressurized vessels.
Spherical butane storage – High-pressure spheres in terminals.
Butane railcar / truck unloading – Pumping from transport tanks into storage.
LPG peak-shaving plants – Transfer butane or butane/propane mixtures to vaporizers.
Refinery butane feed – To alkylation units or blending for gasoline.
Butane export / import terminals – Ship loading/unloading where in-tank pumps are required.
Why choose our API 610 VS6 butane pump?
Full API 610 compliance – Type VS6 verified per standard. Performance test, NPSH test, mechanical run test included.
Zero leakage – No mechanical seal, no packing, no fugitive emissions – best available technology (BAT) for butane.
Low NPSHr – Inducer option allows operation at low NPSHa (below 1 m), preventing pump cavitation damage.
Easy installation – Complete assembly supplied with top flange ready to bolt to tank nozzle.
Short lead time – Standard sizes (e.g., 6”, 8”, 10” discharge) available ex-stock; custom hydraulics 8-12 weeks.
Global spare parts support – Impellers, inducer, bearings, motor stator, and complete replacement cartridges shipped worldwide.
Lower total cost – Competitive initial price plus zero seal maintenance and long MTBR.
Quality assurance
ISO 9001:2015 certified manufacturing.
API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.
NPSH test with inducer (if specified) to verify cavitation performance.
Hydrostatic test of outer can and pressure boundary.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT, UT as required.
How to specify your butane pump
Please provide: flow (m³/h), head (m), operating temperature (°C), tank pressure (bar or MPa), NPSHa available (m), butane purity (pure, commercial LPG, or H₂S content), and tank type (bullet, sphere, etc.). We will recommend pump size, stage count, inducer (optional), material class, and motor rating.
Contact us
For a quotation or technical discussion on butane pumps (API 610 VS6) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.