Rich Amine Pump | API 610 OH2 Centrifugal Pump | China OH2 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 single‑stage, overhung pump for rich amine (H₂S/CO₂ loaded amine) from absorber flash drum to regenerator. Corrosion resistant 316SS/duplex, low NPSH design. Handles particulates (iron sulfide). China OH2 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A rich amine pump transfers amine solution loaded with acid gases (H₂S and CO₂) from the absorber bottom (via a flash drum) to the regenerator (stripper). Rich amine is typically cooler than lean amine (around 40-80°C), but is more corrosive due to dissolved H₂S/CO₂, may contain solid contaminants (iron sulfide, corrosion products), and often operates with very low net positive suction head (NPSH) because it is taken from a flash drum with low liquid level. Our API 610 OH2 centrifugal pump is specifically engineered for rich amine service. This design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches rich amine requirements because:

  • OH2 provides easy maintenance – back pull‑out for seal, impeller, bearing inspection without disturbing piping. Critical for rich amine where solids may require frequent cleaning.

  • Corrosion resistant materials (stainless steel, duplex, Alloy 20) are available in OH2 construction.

  • Low NPSH – Rich amine flash drums often provide less than 2 m NPSHa. Inducer or high‑suction specific speed impeller reduces NPSHr below 1 m.

  • Solids handling capability – Open or semi‑open impeller option for iron sulfide particles up to 3-5 mm.

Why API 610 OH2 for rich amine duty?

  • High corrosion resistance – Rich amine is highly corrosive due to H₂S/CO₂ and high chloride content. Wetted parts specified as 316SS minimum, with 317L, duplex (2205/2507), or Alloy 20 recommended for severe service. NACE MR0175 compliance is typical for H₂S service.

  • Low NPSH capability – Flash drum often has limited height. Inducer reduces NPSHr to below 1 m, preventing cavitation which accelerates degradation and erosion.

  • Solids handling – Rich amine can contain iron sulfide (FeS) particles from corrosion. Semi‑open or open impeller with replaceable wear plate allows passage up to 6 mm solids. Hardened wear rings (17-4PH/Stellite) extend life.

  • Sealing for dirty service – API 682 Plan 31 (cyclone separator) or Plan 32 (external clean flush) recommended to protect seal faces from abrasive particles. Double seals with barrier fluid for zero H₂S emissions (environmental compliance).

  • Efficient continuous duty – Rich amine pumps run 24/7. High efficiency reduces power consumption.

  • Wide hydraulic range – Flow from 10 to 2500 m³/h, head up to 200 m (lower than lean amine typically). Temperature up to 100°C.

Key design features for rich amine service

  • Materials – Casing: 316SS (CF8M), 317L, duplex (CD4MCu), or Alloy 20. Impeller: 316SS, duplex, or 17-4PH. Shaft: 316SS, duplex, or Alloy 20. Wear rings: 17-4PH H1150 or Stellite. Gaskets: PTFE or spiral wound with PTFE.

  • Impeller type – Fully enclosed for clean rich amine. Semi‑open with replaceable wear plate for dirty service (FeS particles). Open impeller for high solids.

  • Inducer – Standard recommendation if NPSHa below 3 m. Enhances suction performance.

  • Sealing – Cartridge mechanical seals. For clean rich amine: Plan 11 (internal recirculation). For solids: Plan 31 (cyclone separator) or Plan 32 (external clean solution flush). For zero H₂S emissions: tandem seal with Plan 52 or double seal with Plan 53A. Seal faces: SiC vs. SiC (for abrasives) or SiC vs. carbon (for clean). Full compliance with API 682.

  • Bearings – Anti‑friction, oil bath or pure oil mist. Bearing housing with labyrinth seals to prevent contamination.

  • Drain and vent – Full drain for complete removal of settled solids. Vent at high point for priming.

  • NACE compliance – Materials and welding per NACE MR0175 / ISO 15156 for H₂S service.

Typical performance range

ParameterValue
Flow rate10 – 2500 m³/h
HeadUp to 200 m
TemperatureUp to 100°C
Pressure ratingUp to 25 bar
NPSHr (with inducer)As low as 0.5 m
Solids passage (semi‑open impeller)Up to 6 mm
Speeds1450 / 2900 / 3600 rpm

Typical applications

  • Rich amine from absorber flash drum to regenerator.

  • Rich amine to flash drum recirculation.

  • Rich amine transfer in high‑pressure gas sweetening plants.

  • Refinery fuel gas and natural gas amine units.

Comparison: Lean Amine vs. Rich Amine Pump

FeatureLean Amine (OH2)Rich Amine (OH2)
Temperature100-120°C40-80°C
CorrosivityModerate (degradation)High (H₂S/CO₂)
SolidsLow (after filters)Moderate (FeS, corrosion products)
NPSHaModerateVery low (flash drum)
SealingPlan 11/23Plan 31/32, double seals for H₂S
Impeller typeClosedSemi‑open / open for solids

Why choose our API 610 OH2 rich amine pump?

  • Full API 610 compliance – Performance test, NPSH test (inducer), mechanical run test included.

  • Superior corrosion/erosion resistance – Material options from 316SS to duplex to Alloy 20, with NACE MR0175.

  • Low NPSH reliability – Inducer prevents cavitation, protecting pump and amine quality.

  • Solids handling design – Semi‑open impeller, replaceable wear plate, hardened wear rings.

  • Zero emission sealing – Double seals with barrier fluid for H₂S containment.

  • Short lead time – Standard 316SS pumps ex‑stock; duplex / Alloy 20 with inducer 8-10 weeks.

  • Global spare parts support – Impellers, seals, wear rings, shafts, casings shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.

  • NPSH test verification (with inducer).

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • PMI (positive material identification) for alloy components.

  • NDE – MT, PT, UT as required.

How to specify your rich amine pump

Please provide: flow (m³/h), head (m), operating temperature (°C), NPSHa (m), amine type (DEA, MEA, MDEA), concentration, H₂S/CO₂ loading, solids content and size (iron sulfide, etc.), required material (316SS / duplex / Alloy 20), and emission regulations (zero H₂S leakage). We will recommend inducer (yes/no), impeller type (closed/semi‑open), seal plan (31/32/52/53A), material class, and driver details.

Contact us

For a quotation or technical discussion on rich amine pumps (API 610 OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit