This page presents verified field cases of our API 610 VS3 vertical single-stage double suction pumps operating reliably in large flow, medium head applications. Each case demonstrates the pump's ability to deliver high flow rates with low NPSH, high efficiency, and long-term stable performance in power plants, municipal water plants, refineries, and seawater intake systems.
Case 1 – Thermal Power Plant Circulating Water (Asia)
Background: A 600 MW thermal power plant needed multiple circulating water pumps for condenser cooling. Total flow requirement was 45,000 m³/h. The plant had limited pump house floor space and required low NPSH due to low cooling tower basin level.
VS3 Pump Solution:
Six VS3 pump sets (4 duty + 2 standby)
Flow per pump: 7,500 m³/h
Head: 22 m
Material: Cast iron casing, bronze impeller
Installation: Pit mounted vertical arrangement
Results:
Large flow stable operation – total 30,000 m³/h with 4 pumps online, full load cooling achieved
Energy saving – high efficiency (89%) compared to previous horizontal pumps
Space saving – vertical layout reduced pump house footprint by 35%
Low NPSH – no cavitation despite low basin level during dry season
Available references: Layout drawing, site photo, pump house footprint comparison.
Case 2 – Municipal Water Plant Raw Water Lifting (Southeast Asia)
Background: A municipal water treatment plant required raw water lifting from a river intake. Available NPSH was limited during low flow season (only 3 meters). Horizontal double suction pumps previously used had cavitation issues.
VS3 Pump Solution:
Flow: 4,200 m³/h
Head: 28 m
Material: Ductile iron casing, stainless steel impeller
Installation: Floor mounted vertical
Results:
Low NPSH no cavitation – double suction design handled low river level without damage
Long-term reliable running – over 3 years continuous operation without bearing or seal failure
High efficiency – 87% at duty point, reducing annual energy cost
Easy maintenance – back pull-out design allowed seal replacement without removing piping
Available references: Installation drawing, site photo, NPSH calculation sheet.
Case 3 – Refinery Large Flow Cooling Water (Middle East)
Background: A refinery needed a large flow cooling water pump to serve its heat exchanger network. The pump had to run 24/7 in a high ambient temperature environment with limited maintenance access.
VS3 Pump Solution:
Flow: 5,800 m³/h
Head: 35 m
Temperature: 45°C (seawater cooling source)
Material: Duplex stainless steel (for seawater cooling corrosion)
Installation: Vertical pit mounted
Results:
Low vibration – well within API 610 limits; vertical cantilever design minimized shaft deflection
High efficiency (88%) – reduced power consumption compared to older pumps
Matched refinery circulating water demand – stable pressure across varying refinery load
Corrosion resistant – duplex material withstood high chloride seawater for 2+ years
Available references: Site photo, vibration log, performance test report.
Case 4 – Seawater Industrial Park Water Supply (China)
Background: An industrial park located on the coast required a seawater supply pump for multiple plant cooling systems. Seawater chlorides required corrosion-resistant materials, and 24/7 operation was mandatory.
VS3 Pump Solution:
Flow: 3,800 m³/h
Head: 42 m
Material: Super duplex stainless steel (casing, impeller, shaft)
Installation: Vertical floor mounted with seawater intake pit
Results:
Anti-corrosion – super duplex material showed no pitting or crevice corrosion after 2 years
Continuous 24h operation – pump ran without any unplanned downtime
Low NPSH – operated reliably from seawater sump with varying tide levels
Simple maintenance – annual bearing check only; internal components in good condition
Available references: Layout drawing, site photo, material certificate (EN 10204 3.1).
What You Can Request From Us for Each Case
Layout drawing (pump house or plant arrangement)
Site photos and installation images
Project parameter sheet (flow, head, material, speed)
Operating parameter reference (vibration, power consumption, uptime)
Why Real Project Cases Matter
Field references prove that our VS3 pumps deliver:
Large flow, stable operation, energy savings in power plant cooling systems
Low NPSH, no cavitation, long-term reliability in municipal water intake
Low vibration, high efficiency in refinery cooling water services
Corrosion resistance, 24/7 continuous operation in seawater service
Get the Complete VS3 Pump Case Study Package
We can match your large flow, medium head, low NPSH conditions to similar successful installations. Request the VS3 pump project case PDF or ask for references in your specific industry.
Email: info@hyrig.com
Please specify your industry (power plant / municipal water / refinery / seawater) and we will send relevant case studies, layout drawings, and operating data within 24 hours. We also welcome inquiries for custom VS3 vertical double suction pump selection and factory direct pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.