The XQ28/2.6Y is a high‑torque upgrade of the XQ28/1.8Y hydraulic sucker rod power tong, specifically engineered for tight, corroded, or seized sucker rod and tubing connections in oil well workover operations. When standard torque isn’t enough, the XQ28/2.6Y delivers the extra power needed to break out rusted threads and make up high‑strength rods with confidence.
| Code | Meaning |
|---|---|
| XQ | Workover (X) – Sucker Rod Tong (Q) |
| 28 | Maximum sucker rod size CYG28 (range CYG16–28) |
| 2.6 | Low gear max torque 2.6 kN·m (key differentiator) |
| Y | Hydraulic drive |
| Parameter | XQ28/1.8Y | XQ28/2.6Y (Upgrade) | Improvement |
|---|---|---|---|
| Low gear torque | 1.8 kN·m | 2.6 kN·m | +44% |
| High gear torque | 0.7 kN·m | 1.0 kN·m | +43% |
| Low gear speed | 40 r/min | 32 r/min | Slightly lower |
| High gear speed | 104 r/min | 98 r/min | Slightly lower |
| System pressure | 10 MPa | 10 MPa | Same |
| Oil flow rate | 65 L/min | 80 L/min | +23% |
| Weight (with backup) | ~95 kg | 106 kg | Heavier duty |
| Dimensions (L×W×H) | 543×334×404 mm | 686×415×516 mm | Larger |
2.6 kN·m low gear torque – 44% more than the 1.8Y model.
Easily breaks out rusty, seized, or over‑torqued sucker rod connections.
Reduces or eliminates dangerous manual hammering on connections.
Low gear (32 rpm) – High‑torque break‑out / back‑out.
High gear (98 rpm) – Fast spinning / make‑up for efficiency.
Master and backup tongs clamp and release simultaneously.
Prevents sucker rod body from rotating during make‑up or break‑out.
Safer and faster than separate manual backup.
Sucker rods – CYG16, 19, 22, 25, 28 (5/8″ – 1⅛″).
Tubing – Φ48 – 60 mm (1 7/8″ – 2 3/8″).
Enables precise make‑up torque to protect threads.
Ideal for premium sucker rod connections requiring specific torque values.
| Scenario | Why XQ28/2.6Y is the right choice |
|---|---|
| Old wells, deep wells, severe corrosion | Long‑term rust and scale make connections extremely tight. Extra 2.6 kN·m torque breaks them free without damaging rods. |
| High‑strength sucker rods | Higher make‑up torque required for proper connection preload. XQ28/2.6Y delivers consistent, adjustable torque. |
| Workover rigs as primary sucker rod tong | One tong handles both routine and difficult jobs – reduces need for backup manual tools. |
| Operations with frequent seized threads | Cuts break‑out time significantly compared to standard 1.8 kN·m tongs. |
44% more low‑end torque – Handles what the 1.8Y cannot.
23% higher oil flow – More hydraulic power for sustained heavy loads.
Heavier construction – Designed to withstand the stress of high‑torque operations without premature wear.
For workover contractors who frequently encounter stuck sucker rod connections, the XQ28/2.6Y is the reliable, time‑saving, and safer alternative to manual wrenches or under‑powered tongs.
Use anti‑wear hydraulic oil ISO VG 46. Maintain oil temperature below 65°C. Keep oil clean with a filter fineness of ≥0.025 mm (25 microns). Recommended flow rate: 80 L/min at 10 MPa.
For inquiries, technical data, or to order the XQ28/2.6Y high‑torque sucker rod power tong, please contact:
info@hyrig.com
We provide fast response, on‑site training, and full after‑sales support for all XQ series tongs – sucker rod, tubing, and drill pipe models.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.