The XQ89/3YC hydraulic power tong is a lightweight, dual‑speed workover tool for make‑up and break‑out of tubing from 2⅜" to 3½". To maintain reliable performance and minimize downtime, stocking the correct genuine TEDA wear parts is essential. This guide provides a complete spare parts list for one XQ89/3YC unit, divided into high‑frequency parts and routine maintenance parts.
These parts wear quickly under normal use and should be kept in stock at all times.
| Part No. | Part Name | Qty per Tong | Application | Replacement Reason |
|---|---|---|---|---|
| 3C1-102 | Jaw die (master tong) | 2 | Tubing gripping, anti‑slip | Wear, slipping |
| 3C2-29 | Jaw die (backup tong) | 2 | Tubing gripping, anti‑slip | Wear, tooth breakage |
| 3C1-104 | Jaw carrier (master tong) | 2 | Holds jaw dies | Deformation, wear |
| 3C2-28 | Jaw carrier (backup tong) | 2 | Holds jaw dies | Deformation, wear |
| 3C1-33 | Brake spring | 11 | Braking, clutch | Fatigue, breakage |
| 3C1-42 | O‑ring | 2 | Hydraulic sealing | Aging, oil leak |
| 3C2-37 | O‑ring 54×3.5 | 2 | Backup hydraulic sealing | Aging, oil leak |
| 3C1-50 | Friction plate | 2 | Brake friction | Wear, reduced braking force |
These parts have longer service lives but should be inspected and replaced at regular maintenance intervals.
| Part No. | Part Name | Qty per Tong | Application |
|---|---|---|---|
| 3C1-4 | Roller | 22 | Jaw climbing, gripping |
| 3C1-7 | Roller shaft | 22 | Supports roller |
| 3C1-14 | Deep groove ball bearing 105 | 4 | Rotational support |
| 3C1-28 | Deep groove ball bearing 205 | 1 | Power input support |
| 3C1-40 | Deep groove ball bearing 208 | 1 | Transmission support |
| 3C1-148 | Tension spring | 1 | Safety door return |
| 3C1-109 | Cylindrical pin | 4 | Jaw die locking |
Use only genuine TEDA original parts – Ensures correct gripping force, sealing integrity, and service life.
Jaw dies – Replace immediately when worn or slipping to avoid damaging tubing threads.
Seals (O‑rings) and bearings – Replace according to scheduled maintenance to prevent hydraulic leaks and mechanical jamming.
Springs and friction plates – Replace when spring force weakens or friction plate wear exceeds the limit.
Important – Non‑genuine parts may cause improper fit, premature failure, unsafe operation, and will void the warranty.
| Part Category | Suggested Stock Level | Replacement Frequency |
|---|---|---|
| Jaw dies (master & backup) | 2–4 sets | Every 200–500 cycles |
| Brake spring (3C1-33) | 11 pieces (full set) | Every 6–12 months |
| Friction plate (3C1-50) | 2–4 pieces | Every 6–12 months |
| O‑rings (3C1-42, 3C2-37) | 2–4 sets | Annually or when leaking |
| Rollers & shafts | 10–20 pieces | As needed |
| Bearings (105, 205, 208) | 1 set each | Annually or when noisy |
For genuine XQ89/3YC wear parts, seal kits, or complete spare parts packages, please contact:
info@hyrig.com
*We offer fast response, original factory packaging, and technical support for all XQ series power tongs (XQ89/3C, XQ89/3YC, XQ114/9, XQ140/12A, and others).*
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.