A Safety Joint is a precisely engineered downhole tool designed to be the weakest, yet most reliable, point in a fishing or workover string. It serves as a planned emergency release mechanism, allowing for a controlled disconnection in the event the bottom hole assembly (BHA) becomes stuck.
The joint is run as an integral part of the BHA, positioned strategically above critical and expensive tools like fishing spears, overshots, or milling assemblies. It is designed to transmit full drilling loads, including weight, torque, and tension, under normal operating conditions.
However, if the tools below it become stuck, a simple, pre-defined procedure (typically involving left-hand rotation and picking up) allows the Safety Joint to be easily unscrewed at its special left-hand thread connection. This enables the upper portion of the drill string to be safely retrieved to the surface. Crucially, the joint leaves a clean, known connection point downhole, which can be easily re-engaged by simply running the joint back in and making up the connection, allowing operations to resume quickly.
| OD (mm / inch) | ID (mm / inch) | Overall Length (mm / ft) | Connection (Typically Box × Pin) |
|---|---|---|---|
| 89 (3-1/2) | 31.8 (1-1/4) | 685 (2.2) | NC26 |
| 95 (3-3/4) | 38.1 (1-1/2) | 663 (2.17) | NC26 |
| 105 (4-1/8) | 38.1 (1-1/2) | 805 (2.6) | NC31 (NC31LH) |
| 105 (4-1/8) | 50.8 (2) | 679 (2.22) | NC31 |
| 121 (4-3/4) | 50.8 (2) | 1060 (3.5) | NC38 (NC38LH) |
| 121 (4-3/4) | 62 (2-7/16) | 712 (2.3) | NC38 |
| 127 (5) | 62 (2-7/16) | 712 (2.3) | NC38 |
| 159 (6-1/4) | 57.2 (2-1/4) | 1000 (3.3) | NC50 (NC50LH) |
| 159 (6-1/4) | 80 (3-5/32) | 781 (2.56) | NC50 |
| 165 (6-1/2) | 70 (2-3/4) | 1100 (3.6) | NC50 |
| 165 (6-1/2) | 82 (3-15/64) | 751 (2.5) | NC50 |
| 168 (6-5/8) | 70 (2-3/4) | 1065 (3.5) | NC50 |
| 168 (6-5/8) | 71.4 (2-13/16) | 1200 (3.9) | NC50 |
| 178 (7) | 70 (2-3/4) | 1100 (3.6) | NC50 |
| 178 (7) | 82 (3-15/64) | 791 (2.59) | NC50 |
| 203 (8) | 80 (3-5/32) | 1065 (3.5) | 6-5/8 REG |
| 203 (8) | 82 (3-15/64) | 841 (2.8) | 6-5/8 REG |
| 229 (9) | 88.9 (3-1/2) | 910 (3.0) | 7-5/8 REG |
Note: Specifications are subject to standard manufacturing tolerances. "LH" denotes a Left-Hand thread, which is standard for the primary release mechanism of a Safety Joint. The tool is designed to be the weakest point in the string with a predictable release torque.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.