The calciner feed pump is a specialised, heavy‑duty centrifugal pump designed to feed the heavy soda ash slurry into the rotary calciner in soda ash production plants (ammonia‑soda / Hou`s process / Union process). After the bicarbonate filtration stage, the filter cake – a slurry containing mainly wet sodium bicarbonate (NaHCO₃) with mother liquor, sodium chloride (NaCl), ammonium chloride (NH₄Cl), and carbonates – must be pumped to the calciner at high temperature (120‑200°C) for thermal decomposition into light soda ash.
This feed service is one of the most demanding in the entire soda ash process because:
High temperature: 120‑200°C – near the boiling point of the liquor.
High solids content: 5‑15% suspended fine crystals (bicarbonate, carbonate, salt particles).
Abrasive/corrosive: Chlorides and carbonates cause pitting; solids cause seal and impeller wear.
Fluctuating properties: Varying density, viscosity, and crystal size require a robust, wide‑operating pump.
The pump is classified under API 610 (ISO 13709) as Type OH2 – a full centreline‑mounted, radially split, single‑stage, overhung centrifugal pump. The centreline mounting maintains alignment at high temperatures, while the single‑stage design provides wide internal passages for solids passage and easy maintenance via back pull‑out. The robust design of the pumps, as well as the reliable hydraulic version, enables fulfillment of all requirements of the application in many fields.
This pump is manufactured by a leading China API 610 pump manufacturer with a proven track record in severe service applications, fully certified to API Q1 and compliant with the latest edition of API 610 / ISO 13709.
| Feature | Description |
|---|---|
| API 610 Type | OH2 (overhung, centreline‑mounted, radially split, single‑stage) |
| Casing form | Radially split, centreline support feet |
| Bearing support | Overhung – impeller overhangs from bearing housing; bearings at drive end only |
| Number of stages | Single stage |
| Suction type | Single‑suction (end suction, top discharge) |
| Flange rating | ANSI Class 300 / 600 / 900 (as required) |
| Compliance | API 610 11th / 12th edition (ISO 13709) |
Centreline mounting – Pump feet are cast on the casing centreline, allowing the casing to expand uniformly when handling hot slurry at 120‑200°C. This prevents shaft misalignment and bearing distress. The pump casing is centreline mounted to maintain alignment during operation and elevated temperatures.
Radially split casing – The casing is split in a vertical plane perpendicular to the shaft, providing a robust pressure‑containing joint suitable for hot, abrasive, corrosive fluids.
Back pull‑out design – The complete rotating assembly (impeller, shaft, bearing housing, mechanical seal) can be removed without disconnecting suction or discharge piping – essential for pumps that require frequent inspection of impeller and wear rings due to solids abrasion. The pump internals can be taken out without disconnecting suction/delivery piping or moving driver.
Finned bearing housing – Provides maximum heat dissipation under API 610 compliance, eliminating the need for cooling water even at 200°C.
Single‑stage simplicity – No interstage seals; wide internal passages allow solids up to 10‑15 mm to pass without clogging.
The HP‑OH2 pump is a single‑stage, horizontal, radically split volute casing overhung pump with foot mounted, complying with the requirements of API 610 and ISO 13709. It not just meets the requirements of API 610 but also benefits from years of operational experience in the field.
| Parameter | Design Range |
|---|---|
| Flow rate | 50 – 500 m³/h (220 – 2,200 GPM) |
| Head | 40 – 100 m (130 – 330 ft) |
| Slurry temperature | 120 – 200°C (248 – 392°F) |
| Solids content | 5 – 15% by weight (NaHCO₃ crystals, NaCl, carbonates) |
| Specific gravity | 1.15 – 1.60 (depending on solids concentration) |
| Maximum pressure | 2.5 – 5.0 MPa (25 – 50 bar) |
| Speed | 1,450 / 2,950 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz) |
| NPSHr | Optimised (≤5 m) – double‑suction option or inducer available |
| Pump efficiency | 65‑78% (depending on solids content and specific gravity) |
| Design life | 20 years minimum |
The performance envelope of API 610 overhung pumps includes: design pressure rating up to 40 barg, temperature rating up to 427°C (800°F), flowrate up to 4000 m³/h (17600 USgpm), differential head up to 300 m (980 ft).
Calciner feed slurry contains abrasive crystals, and the mother liquor portion is corrosive due to chlorides, carbonates, and ammonia. Material selection must balance both.
| Component | Standard Material | Upgrade Option | Remarks |
|---|---|---|---|
| Casing | Alloy cast iron (Ni‑Hard / high‑chromium) | Duplex stainless steel (D‑1/D‑2) | Alloy iron resists abrasion; duplex resists chlorides |
| Impeller | Alloy cast iron (hardened) | CD4MCu (duplex) or 316L with hard coating | Abrasion‑resistant; closed impeller standard |
| Wear rings | Hardened alloy iron or 316L + Stellite | Tungsten carbide coated | Extends life in abrasive slurry |
| Shaft | 4140 hardened steel (coated) | 17‑4 PH or duplex stainless steel | High strength at elevated temperature |
| Seal chamber / gland | Alloy cast iron or 316L | Duplex | – |
| Baseplate | Heavy‑duty steel, grouted | Stainless steel (washdown areas) | – |
High abrasion (sharp crystals, >10% solids) → Alloy cast iron (Ni‑Hard, hardness ≥550 BHN) – excellent erosion resistance. This pump also includes closed impeller or open impeller with Coke Crusher design, wear plate, and hard metal coating as needed.
High corrosion (chlorides >5,000 ppm, low pH) → Duplex stainless steel (2205 / CD4MCu) – good pitting resistance and strength.
Combined severe abrasion + corrosion → Duplex stainless steel with hard coating on wear rings and impeller.
All materials are available as standard to match your applications; for API‑610, from S‑1, S‑4, S‑6, S‑7, S‑8, C‑6, A‑7, A‑8, D‑1, D‑2, and specialty or higher grades are also available, plus NACE compliant materials.
Solids in the calciner feed slurry (5‑15%) are the primary cause of mechanical seal failure. Standard carbon vs. ceramic seal faces will be destroyed rapidly. The seal area meets API 610/682, suitable for a variety of seals.
| Seal Arrangement | API 682 Plan | Suitability |
|---|---|---|
| Dual pressurised (Arrangement 3) | Plan 53B | Zero emissions, but barrier fluid may not flush solids effectively – requires clean flush |
| Single seal with external clean flush | Plan 32 | Highly recommended – continuous injection of clean external fluid (clarified liquor, condensate, or water) at 1‑2 bar above pump suction pressure washes solids away from seal faces |
| Single seal with quench | Plan 62 | Acceptable with steam or water quench to prevent solids buildup on atmosphere side |
Silicon carbide vs. tungsten carbide – Extremely hard (tungsten carbide >1,800 Hv), excellent for abrasive solids.
Silicon carbide vs. silicon carbide – Hard, acceptable for moderate solids (5‑10%).
Elastomers: Viton (FKM) or Aflas – resistant to hot ammonia, chlorides, and carbonates up to 200°C.
Important: Regardless of seal type, Plan 32 (external clean flush) is strongly recommended for calciner feed slurry with >5% solids. The flush flow rate should be sufficient to keep solids from entering the seal chamber (typically 5‑15 L/min, depending on pump size).
Our calciner feed pump is designed and manufactured by a premier China API 610 pump manufacturer with decades of experience in severe duty process applications.
API Q1 certified – Full quality management system for petroleum and petrochemical pumps.
API 610 11th/12th edition compliance – Fully compliant with ISO 13709.
Engineering excellence – Over 50 years of fluid machinery production experience. The company has a history of more than 50 years in the production of fluid machinery and has passed API certification.
Global references – Thousands of API 610 OH2 pumps installed in soda ash plants, refineries, chemical plants, and other demanding industries worldwide.
Modular design – Wide ranging interchangeability of components such as shafts, casings, covers, wear rings, shaft seals and bearings among the various pump ranges.
Expert technical support – In‑house engineering team for custom hydraulic design, material selection, and seal plan optimisation.
The CP‑OH2 series centreline support single‑stage cantilever centrifugal pump implements API610 11th edition and ISO 13709 standard, and is a radial split, single‑stage cantilever pump suitable for various occasions. The series has carried out thoughtful consideration in hydraulic design, connection method of pump body and bearing support, rotor rigidity, mechanical seal components, cooling methods and auxiliary systems, with some design standards exceeding API610 standard.
API 610 full compliance (OH2) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.
Centreline mounting – Critical for high‑temperature slurry at 120‑200°C, prevents misalignment during thermal expansion.
High solids tolerance – 5‑15% suspended solids pass without clogging, using back pull‑out design for easy cleaning.
Abrasion‑resistant materials – Alloy cast iron (Ni‑Hard / high‑chromium) with hardened wear rings.
API 682 Plan 32 ready – External clean flush prolongs seal life dramatically in abrasive service.
Back pull‑out maintenance – Minimal downtime; replace seals and wear rings without removing piping.
High temperature capability – Finned bearing housing dissipates heat; no cooling water required.
Broad hydraulic coverage – Flows 50‑500 m³/h, heads 40‑100 m, covering virtually all calciner feed duties.
Certified China manufacturer – API Q1, ISO 9001, with global references and export experience.
Proven in soda ash – Thousands of OH2 pumps operating in carbonate filtration and calciner feed circuits worldwide.
Hydrostatic test – Casing tested at 1.5× MAWP.
Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).
Mechanical run test – 4 hours minimum; vibration and bearing temperature recorded.
NPSH test – Optional, when specified.
Impeller dynamic balancing – Grade G6.3 or better.
Material certification – EN 10204 3.1 for pressure‑containing components; PMI available.
NDE – Dye penetrant on castings; ultrasonic on shafts; as required by API 610.
Third‑party inspection – Available (DNV, Lloyds, BV, SGS).
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 32 ready, tungsten carbide faces) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Shaft sleeve (hardened) | 1 |
| Impeller (for critical duty) | 1 set |
| Gasket / O‑ring kit (full set) | 1 set |
For a detailed selection of the API 610 OH2 calciner feed pump for your soda ash production plant – including flow, head, slurry temperature, solids percentage and composition, NPSHa, material selection (alloy cast iron vs. duplex), and API 682 seal plan (Plan 32 with tungsten carbide faces) – please contact our engineering team.
Email: info@hyrig.com
Our API 610 OH2 calciner feed pumps are specifically engineered for the most severe soda ash calciner feed service – handling 5‑15% hot solids at 200°C with proven abrasion‑resistant seals and materials. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with back pull‑out design to minimise downtime and centreline mounting to ensure alignment even at extreme temperatures.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.