Heat Recovery Circulation Pump – Heavy Soda Service – API 610 OH2 Centrifugal Pump by Leading China 610 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 heat recovery circulation pump specifically engineered for heavy soda heat recovery circuits in soda ash production. Centreline mounted, radially split, single‑stage overhung design. Handles hot slurry with 10‑20% suspended solids at 120‑180°C. Alloy cast iron or 316L stainless steel wetted parts. Abrasion‑resistant mechanical seal with external flush (Plan 32) or dual pressurised seal (Plan 53B). Back pull‑out design. Manufactured by a certified China API 610 pump manufacturer. Flow 50‑500 m³/h, head 40‑100 m. 20‑year design life, 3‑year continuous operation.

Conatct For Details
DetailReview(0)Additional

Product Overview

The heat recovery circulation pump is a specialised, heavy‑duty centrifugal pump designed to circulate hot mother liquor and slurry in heat recovery circuits of soda ash production plants (ammonia‑soda / Hou`s process). After the calcination step, large amounts of heat are recovered from the hot soda ash slurry, mother liquor, and off‑gases. This heat recovery loop pumps a corrosive, abrasive, high‑temperature fluid containing 10‑20% suspended solids (sodium carbonate, bicarbonate, salt crystals, and other insolubles) at 120‑180°C.

This service is extremely demanding due to:

  • High temperature: 120‑180°C – near the boiling point of the liquor.

  • High solids content: 10‑20% suspended crystals causing severe abrasion.

  • Corrosive environment: Chlorides, carbonates, and ammonia attack standard materials.

  • Continuous duty: Heat recovery circuits operate 24/7 for years without shutdown.

The pump is classified under API 610 (ISO 13709) as Type OH2 – an overhung, centreline‑mounted, radially split, single‑stage centrifugal pump. Centreline mounting is essential for high‑temperature operation (prevents misalignment due to thermal expansion). The single‑stage design provides wide internal passages for solids passage, and the back pull‑out feature allows maintenance without disconnecting piping.

This pump is manufactured by a leading China API 610 pump manufacturer with full API Q1 certification, decades of experience in severe‑duty pumping, and thousands of units operating in soda ash plants globally.

Construction & API 610 Classification

FeatureDescription
API 610 TypeOH2 (overhung, centreline‑mounted, radially split, single‑stage)
Casing formRadially split volute, centreline support feet
Bearing supportOverhung (impeller overhangs from bearing housing; bearings only at drive end)
Number of stagesSingle stage
Suction typeEnd suction (single‑suction), top discharge
Flange ratingANSI Class 300 / 600 as required
ComplianceAPI 610 11th / 12th edition (ISO 13709)

Why OH2 for Heat Recovery Circulation with Heavy Soda

  • Centreline mounting – The pump feet are cast on the casing centreline, allowing the entire casing to expand uniformly when handling hot slurry at 120‑180°C. This prevents shaft misalignment and bearing failure – a critical requirement for high‑temperature heat recovery loops.

  • Radially split casing – Provides a robust pressure‑containing joint suitable for high temperatures and abrasive fluids.

  • Back pull‑out design – The complete rotating assembly (impeller, shaft, bearing housing, mechanical seal) can be removed without disconnecting suction or discharge piping. This is essential for pumps that require frequent inspection of impeller, wear rings, and seals due to solids abrasion.

  • Finned bearing housing – Dissipates heat effectively; no cooling water required even at 180°C, simplifying the pump installation.

  • Single‑stage open passages – Wide internal flow passages allow solids up to 10‑15 mm to pass without clogging.

Key Technical Specifications (Heat Recovery Circulation Duty)

ParameterDesign Range
Flow rate50 – 500 m³/h (220 – 2,200 GPM)
Head40 – 100 m (130 – 330 ft)
Fluid temperature120 – 180°C (248 – 356°F)
Solids content10 – 20% by weight (Na₂CO₃, NaHCO₃, NaCl crystals)
Specific gravity1.15 – 1.60 (depending on solids concentration)
Maximum pressure2.5 – 5.0 MPa (25 – 50 bar)
Speed1,450 / 2,950 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz)
NPSHrOptimised (≤5 m) – double‑suction or inducer option available
Pump efficiency60‑75% (depending on solids content and specific gravity)
Design life20 years minimum

Materials – Alloy Cast Iron or 316L Stainless Steel

The heat recovery fluid contains both abrasive crystals (10‑20% solids) and corrosive chlorides/ammonia. Material selection must balance abrasion resistance and corrosion resistance.

ComponentStandard MaterialUpgrade OptionRemarks
CasingAlloy cast iron (Ni‑Hard / high‑chromium)316L stainless steelAlloy iron excellent for abrasion; 316L for corrosion
ImpellerAlloy cast iron (hardened)316L with hard coatingAbrasion‑resistant
Wear ringsHardened alloy iron or 316L + StelliteTungsten carbide coatedExtends life in abrasive slurry
Shaft4140 hardened steel (coated)17‑4 PH or 316L stainless steel–
Seal chamber / glandAlloy cast iron or 316LDuplex–
BaseplateHeavy‑duty steel, groutedStainless steel–

Material Selection Guidelines for Heat Recovery Service

  • If abrasion is dominant (sharp crystals, >15% solids) → Alloy cast iron (Ni‑Hard, hardness ≥550 BHN). This material is proven in heavy soda ash slurries.

  • If corrosion is dominant (high chlorides, low pH, less abrasive) → 316L stainless steel. 316L contains molybdenum (2‑3%), providing good pitting resistance in chloride environments.

  • For combined severe abrasion + corrosion → Duplex stainless steel (2205) with hardened wear rings.

All materials are supplied with EN 10204 Type 3.1 certification and full traceability. NACE MR0175 compliance available upon request.

Mechanical Seals – Abrasion‑Resistant for 10‑20% Solids

Solids are the biggest enemy of mechanical seals. With 10‑20% suspended crystals, standard carbon vs. ceramic seal faces will fail within days. The pump must be equipped with a seal system that keeps solids away from seal faces.

Seal ArrangementAPI 682 PlanSuitability
Single seal with external clean flushPlan 32Highly recommended – continuous injection of clean external fluid (clarified liquor, condensate, or water) at 1‑2 bar above pump suction pressure flushes solids away from seal faces
Dual pressurised (Arrangement 3)Plan 53BZero emissions, but barrier fluid alone does not flush solids – must be combined with Plan 32 or a clean flush
Single seal with quenchPlan 62Acceptable with steam or water quench to prevent solids buildup on atmosphere side, but not for high solids

Recommended Seal Face Materials

  • Silicon carbide vs. tungsten carbide – Tungsten carbide faces are extremely hard (>1,800 Hv) and resists abrasion from sharp crystals. This is the preferred choice.

  • Tungsten carbide vs. tungsten carbide – Ultimate abrasion resistance for very high solids (>20%).

  • Silicon carbide vs. silicon carbide – Acceptable for moderate solids (10‑15%) but less resistant than tungsten carbide.

Elastomers: Viton (FKM) or Aflas – resistant to hot ammonia, chlorides, and carbonates up to 180°C.

Critical design note: The seal flush must be continuous and at a flow rate sufficient to prevent solids ingress. A typical flow rate is 5‑15 L/min. The flush fluid should be clean and compatible with the process.

NPSH & Cavitation Control

Hot heat recovery fluid at 120‑180°C has high vapour pressure. Available NPSH may be limited because the pump may take suction from a tank or sump with moderate liquid level. To prevent cavitation:

  • Low NPSHr impeller design – Optimised inlet geometry for high temperature service.

  • Inducer option – Axial inducer reduces NPSHr by 40‑60%, especially beneficial when NPSHa < 4 m.

  • Double‑suction first‑stage impeller (available on larger OH2 frames) – further reduces NPSHr.

  • Never throttle on suction side – Always control flow via discharge valve.

Applications

IndustrySpecific Service
Soda ash (Solvay / Hou`s process) | Heat recovery circulation from calciner off‑gas scrubbers, mother liquor heat exchangers |
Heavy soda ash productionRecirculation of hot slurry between heat recovery vessels and columns
Bicarbonate processPumping hot mother liquor with crystals to heat recovery equipment
Chemical & fertilizerSimilar high‑temperature, high‑solids heat recovery loops

Why Choose an API 610 OH2 Heat Recovery Circulation Pump from This China Manufacturer

  • API 610 full compliance (OH2) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.

  • Centreline mounting – Essential for high‑temperature slurry at 120‑180°C, prevents misalignment and bearing failure.

  • High solids tolerance – 10‑20% suspended solids pass without clogging, with wide internal passages and back pull‑out cleaning access.

  • Abrasion‑resistant materials – Alloy cast iron (Ni‑Hard) or 316L stainless steel with hardened wear rings.

  • API 682 Plan 32 ready – External clean flush with tungsten carbide seal faces prolongs seal life dramatically.

  • Back pull‑out maintenance – Replace seals and wear rings without removing piping, minimising downtime.

  • High temperature capability – Finned bearing housing dissipates heat; no cooling water required.

  • Broad hydraulic coverage – Flows 50‑500 m³/h, heads 40‑100 m, covering all heat recovery circulation duties.

  • Certified China manufacturer – API Q1, ISO 9001, with global references in soda ash and heavy chemical industries.

  • Proven in heavy soda service – Thousands of OH2 pumps operating in soda ash heat recovery circuits worldwide.

Quality Assurance & Testing (Per API 610)

  • Hydrostatic test – Casing tested at 1.5× MAWP.

  • Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).

  • Mechanical run test – 4 hours minimum; vibration and bearing temperature recorded.

  • NPSH test – Optional, when specified.

  • Impeller dynamic balancing – Grade G6.3 or better.

  • Material certification – EN 10204 3.1 for pressure‑containing components; PMI available.

  • NDE – Dye penetrant on castings; ultrasonic on shafts; as required by API 610.

  • Third‑party inspection – Available (DNV, Lloyds, BV, SGS).

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (Plan 32 ready, tungsten carbide vs. silicon carbide faces)1 set
Wear ring set (casing + impeller)1 set
Bearing set (radial + thrust)1 set
Shaft sleeve (hardened)1
Impeller (for critical duty)1 set
Gasket / O‑ring kit (full set)1 set

Get a Quote or Engineering Support

For a detailed selection of the API 610 OH2 heat recovery circulation pump for your heavy soda ash heat recovery circuit – including flow, head, slurry temperature, solids percentage and composition, NPSHa, material selection (alloy cast iron vs. 316L vs. duplex), and API 682 seal plan (Plan 32 with tungsten carbide faces) – please contact our engineering team.

Email: info@hyrig.com

Our API 610 OH2 heat recovery circulation pumps are specifically engineered for the most severe heavy soda heat recovery service – handling 10‑20% hot solids at 180°C with proven abrasion‑resistant seals and materials. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with back pull‑out design to minimise downtime and centreline mounting to ensure alignment even at extreme temperatures.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit