The mother liquor transfer pump is a critical centrifugal pump specifically engineered for handling mother liquor in soda ash production projects using the Hou's process (combined process) or traditional Solvay (ammonia‑soda) process. Mother liquor is the residual saturated liquid remaining after sodium bicarbonate or ammonium chloride crystals have been removed from the solution. It is typically high in ammonium chloride (NH₄Cl), sodium chloride (NaCl), and dissolved ammonia, and is saturated or near‑saturated. This liquor is either recycled back to the carbonating towers for further reaction, or sent to the ammonia recovery section for regeneration.
Pumping mother liquor presents multiple challenges: high chloride concentration (causes pitting corrosion), ammonia content (toxic, corrosive to copper‑based alloys), presence of small entrained crystals (abrasive), potential for crystallisation on pump internals if temperature drops or flow velocity is insufficient, and medium operating temperatures (40‑100°C). Our API 610 mother liquor transfer pumps are specifically designed for these demanding conditions, fully compliant with API 610 11th/12th edition (ISO 13709) – ensuring 20‑year design life and minimum 3‑year uninterrupted operation.
These pumps are ideal for soda ash greenfield and brownfield projects, including those in Indonesia, China, India, and other major soda ash producing regions.
| Pump Type | API 610 Type | Best Application for Mother Liquor |
|---|---|---|
| OH2 | Overhung, centreline‑mounted, single‑stage | Standard mother liquor circulation from carbonating tower bottom to filter feed or recycle tank (heads ≤150 m) |
| BB3 | Axially split, single casing, multistage, between bearings | High‑head mother liquor transfer to elevated dechlorinators, ammonia recovery columns, or long‑distance pipelines (heads up to 400 m) |
| VS4/VS6 | Vertical suspended sump or can type | Suction from low‑level sumps or when very low NPSH is required |
Single‑stage overhung impeller, centreline mounted – accommodates moderate thermal expansion.
Back pull‑out design – rotating assembly removable without disturbing suction or discharge piping.
Heavy‑duty API 610 bearing housing; L10 bearing life ≥25,000 hours.
Flow range: 10 – 600 m³/h; head range: 10 – 150 m (higher with larger frames).
Double volute casing on larger sizes to balance radial thrust.
Enlarged shaft diameter for stability when handling saturated brines.
Horizontal, single‑casing, axially split, centreline‑mounted, between‑bearings centrifugal pump.
Opposed (back‑to‑back) impellers – axial thrust self‑balanced without complex balance devices. This design is especially good for liquids that may contain fine solids.
Radial forces self‑balanced by volute type flow channels symmetrically arranged along the centreline.
Flow range: 10 – 1,600 m³/h; head up to 1,600 m; temperature range –80 to +200°C; pressure up to 25 MPa.
Suction and discharge cast with casing – rotor can be easily maintained without dismounting suction and discharge pipelines, reducing shutdown downtime.
Ideal for transferring mother liquor to elevated dechlorinators or ammonia recovery columns.
| Parameter | OH2 | BB3 |
|---|---|---|
| Flow range | 10 – 600 m³/h | 10 – 1,000 m³/h |
| Head range | 10 – 150 m (up to 260 m with larger frame) | 50 – 400 m |
| Max temperature | –80 to +150°C | –80 to +200°C |
| Pressure rating | Up to 7.5 MPa | Up to 25 MPa |
| Speed | 1,450 / 2,950 rpm | 1,450 / 2,950 rpm |
| Max mother liquor density | ≤1.4 g/cm³ | ≤1.4 g/cm³ |
| Max solids (suspended crystals) | ≤1% by volume | ≤1% by volume |
Mother liquor in soda ash process contains ammonium chloride (NH₄Cl), sodium chloride (NaCl), carbonates, ammonia, and small amounts of bicarbonate solids. Chloride concentration can be high, causing pitting in standard stainless steels. Material selection must address both chloride corrosion and mild abrasion from entrained crystals.
| Component | Recommended Material | API 610 Class |
|---|---|---|
| Casing | 316L stainless steel (CF3M) | S‑8 |
| Impeller | 316L stainless steel or duplex (2205) | S‑8 / D‑1 |
| Shaft | 316 stainless steel or 17‑4 PH | A‑8 / C‑6 |
| Wear rings | 316L SS + Stellite hard‑faced | – |
| Gaskets / O‑rings | PTFE or Viton (FKM) | – |
| Fasteners | 316 stainless steel | – |
To reliably pump mother liquor with high chloride content, 316L stainless steel is the minimum recommended material due to its molybdenum content (2‑3%), which improves pitting resistance. For more aggressive mother liquor (higher temperature, higher chloride, or presence of chloramines), duplex stainless steel (2205 – API 610 Class D‑1) offers even better pitting resistance (PREN >35) and higher strength.
Carbon steel – rapid chloride pitting, unacceptable for mother liquor service.
304 stainless steel – insufficient molybdenum, prone to pitting with hot chlorides.
Copper alloys – ammonia attacks copper and brass. Do not use any copper‑based wetted parts.
Because mother liquor may contain small crystals (bicarbonate or ammonium chloride crystals), the pump is equipped with:
Hardened wear rings (316L + Stellite) to maintain hydraulic clearance.
Replaceable throat bushings and shaft sleeves.
Optional silicon carbide or tungsten carbide seal faces to resist abrasion.
Mother liquor frequently contains entrained crystals and has high salt concentration, which standard mechanical seals cannot tolerate.
| Seal Arrangement | API 682 Plan | Application for Mother Liquor |
|---|---|---|
| Single seal with external flush | Plan 32 | Recommended – clean external flush liquid (deaerated water or condensate) injected into seal chamber to flush away solids and keep seals clean |
| Dual pressurised seal (Arrangement 3) | Plan 53B | Zero emissions; used for ammonia‑containing mother liquor to prevent toxic leakage |
| Single seal with quench | Plan 62 | Lower cost, quench steam or water on atmosphere side prevents crystal accumulation |
Plan 32 is especially important for mother liquor duty: an external clean fluid (deaerated water, condensate, or dilute ammonia water) is injected into the seal chamber at 1‑3 bar above suction pressure to:
Wash away solids that could abrade seal faces.
Dilute the saturated mother liquor locally to prevent crystallization on seal faces.
Cool the seal faces.
For mother liquor with high ammonia content (toxic emission concern), Arrangement 3 with Plan 53B (nitrogen‑charged bladder accumulator) is specified to ensure zero ammonia leakage.
Seal faces: Silicon carbide vs. carbon (standard) or silicon carbide vs. silicon carbide (for abrasive mother liquor). Elastomers: Viton (FKM) or PTFE.
Mother liquor transfer pumps typically take suction from a filtrate tank, evaporator body, or crystallizer bottom, often with limited NPSHa. The fluid is saturated and may flash easily.
Low suction specific speed hydraulics with wide choice of impellers for optimum efficiency over a large operating range.
Inducer option – reduces NPSHr by 40‑60% for problematic suction conditions.
Maintain NPSHa ≥ NPSHr + 1.0 m per API 610.
For low NPSHa situations, consider a VS6 vertical can pump to submerge the first‑stage impeller.
During process startups, shutdowns, or low demand periods, pump flow may drop below Minimum Continuous Stable Flow. An automatic recirculation valve (ARC) or a continuous bypass line with orifice must be installed to protect the pump from overheating, vibration, and crystallization.
To prevent mother liquor from crystallising inside the pump during outages or low flow:
Steam jacket or electric heat tracing on the pump casing and seal chamber for critical mother liquor that crystallises easily (e.g., ammonium chloride brine or sodium bicarbonate slurry).
Jacketed stuffing box – optional heating/cooling jacket around seal chamber.
Flush before shutdown – circulate warm water or dilute ammonia solution to flush out saturated mother liquor.
Automatic drainage of casing when auxiliary seal water is disrupted.
| Application | Fluid | Configuration |
|---|---|---|
| Carbonating tower mother liquor circulation | NH₄Cl‑NaCl‑H₂O, saturated | OH2 (single‑stage) |
| Ammonium chloride crystallizer feed | Mother liquor from bicarbonate filtration | OH2 with Plan 32 seals |
| Mother liquor transfer to ammonia recovery column | NH₄Cl brine, hot | BB3 multistage (high head) |
| Dechlorinator feed | Mother liquor with suspended solids | OH2 (316L SS + hardened wear rings) |
| Evaporator mother liquor circulation | Concentrated brine | OH2 or BB3 (duplex material) |
| Bicarbonate wash liquor transfer | Dilute mother liquor | OH2 (304 or 316L SS) |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours
Critical speed: First lateral critical speed ≥120% of maximum operating speed
Centreline mounting (OH2/BB3) – accommodates thermal expansion
Hydrostatic test: 1.5x design pressure
Performance test: Water per API 610 Grade 2 or Grade 1
Material certification: EN 10204 3.1 full traceability
Optional NACE MR0175 for sour service (if mother liquor contains H₂S from coal‑based route)
Full API 610 compliance – OH2 and BB3 types covering the entire soda ash mother liquor circuit.
316L stainless steel or duplex wetted parts – resists chloride pitting and ammonia corrosion.
API 682 Plan 32 seals (external flush) – prevents seal face crystallization and abrasion from entrained solids.
Option for Plan 53B dual pressurised seals – zero ammonia emissions where required.
Low NPSH design – inducer option for problematic suction conditions.
Centreline mounting (OH2/BB3) – maintains alignment during temperature cycles.
Back pull‑out (OH2) or axial split (BB3) design – easy maintenance without removing piping.
Anti‑crystallisation jackets – steam or electric tracing available for mother liquor prone to salting.
Field proven – thousands of API 610 pumps operating in soda ash plants worldwide (Hou's process and Solvay process).
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 32 or Plan 53B ready) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O‑ring kit (full set) | 1 set |
| Shaft sleeve (coated) | 1 set |
| Inducer (if fitted) | 1 set |
For detailed selection of the correct mother liquor transfer pump for your soda ash project – including flow and head requirements, mother liquor composition (NH₄Cl, NaCl, solids content), temperature, NPSHa calculation, material selection (316L SS, duplex or super duplex), API 682 seal plan (Plan 32 for solids flush, Plan 53B for ammonia containment), and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support soda ash greenfield and brownfield projects worldwide – from Hou's process to Solvay – with reliable API 610 mother liquor transfer pumps, corrosion‑resistant, zero‑emission, and built for 20‑year service.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.