The absorber feed / reflux pump is a critical centrifugal pump in gas sweetening (amine treating) and carbon capture (CCUS) processes. It performs two related duties:
Absorber feed (lean amine charge) – pumps regenerated lean amine (MDEA, MEA, DEA) from the bottom of the regenerator or lean amine tank to the top of the absorber column, where it contacts sour gas to remove H₂S and CO₂.
Absorber reflux – returns condensed overhead liquid from the absorber to the top of the column to control temperature, maintain vapour‑liquid equilibrium, and recover amine.
Both duties require a reliable, corrosion‑resistant pump with moderate head (30‑120 m) and moderate flow (50‑500 m³/h), operating at 40‑80°C. The fluid is typically lean amine (MDEA/MEA) or reflux condensate containing water, amine, and residual acid gases. Our API 610 OH2 pump is specifically engineered for these services, fully compliant with API 610 11th/12th edition (ISO 13709) – ensuring 20‑year design life and minimum 3‑year uninterrupted operation.
The OH2 type is the standard configuration for absorber feed and reflux duties because of its moderate head requirement, compact footprint, and easy maintenance.
| Feature | Description |
|---|---|
| Type | OH2 – overhung, centreline‑mounted, single‑stage |
| Impeller | Single‑suction, enclosed (closed) |
| Casing | Radially split, centreline mounting |
| Maintenance | Back pull‑out design – rotating assembly removable without disturbing piping |
| Bearing housing | Heavy‑duty, oil bath lubrication, L10 life ≥25,000 hours |
For taller absorbers or higher pressure differentials, a BB3 multistage pump can be offered (not typical for this duty).
| Parameter | Value Range |
|---|---|
| Flow range | 50 – 500 m³/h |
| Head range | 30 – 120 m |
| Temperature range | 40 – 80°C |
| Pressure rating | Up to 2.5 MPa (25 bar) – suitable for typical absorber operating pressure |
| Speed | 1,450 / 2,950 rpm (50Hz) or 1,750 / 3,550 rpm (60Hz) |
| NPSHr | Optimised (≤4 m at rated flow) – inducer optional |
| Efficiency | 70‑82% at BEP |
The fluid handled (lean amine or reflux condensate) is corrosive due to residual H₂S, CO₂, heat‑stable salts, and possibly chlorides. Material selection follows API 610 Table H.
| Component | Standard (316L SS) | Upgrade (Duplex) | Remarks |
|---|---|---|---|
| Casing | 316L SS (CF3M) – S‑8 | Duplex 2205 (D‑1) | 316L sufficient for most lean amine; duplex for high chloride/very sour |
| Impeller | 316L SS | Duplex | Corrosion resistance |
| Shaft | 316 SS | Duplex or 17‑4 PH | – |
| Wear rings | 316L SS + Stellite | Duplex + Stellite | Extends life in abrasive service |
| Gaskets / O‑rings | PTFE or Viton (FKM) | Viton / Aflas | – |
Recommended material:
316L stainless steel (S‑8) – preferred for nearly all absorber feed and reflux duties. It contains molybdenum (2‑3%), providing excellent resistance to pitting in amine and H₂S/CO₂ environments.
Duplex 2205 (D‑1) – specified when chlorides are present (e.g., seawater cooling in the absorber overhead condenser) or when H₂S partial pressure exceeds NACE limits.
Lean amine and reflux condensate may contain residual H₂S, which is toxic. Sealing must prevent fugitive emissions.
| Seal Arrangement | API 682 Plan | Application |
|---|---|---|
| Dual pressurised (Arrangement 3) | Plan 53B (bladder accumulator) | Recommended – zero emissions, barrier fluid pressure > process. Mandatory for H₂S service. |
| Tandem seal (Arrangement 2) | Plan 52 | Acceptable for low‑H₂S lean amine (<50 ppm) – but Plan 53B is strongly preferred. |
| Single seal (Arrangement 1) | Plan 11 / 21 | Not recommended – H₂S leakage risk. |
Plan 53B uses a nitrogen‑charged bladder accumulator to keep barrier fluid pressure above process pressure, eliminating any amine or H₂S leakage.
Seal faces: Silicon carbide vs. carbon (standard) or silicon carbide vs. silicon carbide (for abrasive service). Elastomers: Viton (FKM) for up to 80°C; Aflas for higher temperatures or aggressive chemicals.
The absorber feed pump typically takes suction from a lean amine tank or regenerator bottom located near the pump. The reflux pump takes suction from the overhead accumulator (reflux drum). NPSHa is usually adequate (3‑6 m). However:
Calculate NPSHa at bubble point – do not assume subcooling, because amine contains dissolved gases (H₂S, CO₂, methane).
Maintain NPSHa ≥ NPSHr + 1.0 m per API 610.
Inducer option available for low NPSHa situations (e.g., low reflux drum elevation).
During startup, shutdown, or low-load operation (turndown), the pump may run below Minimum Continuous Stable Flow. An automatic recirculation valve (ARC) or continuous bypass with orifice returns minimum flow to the suction source (tank or drum).
| Process | Duty | Fluid | Pump type |
|---|---|---|---|
| Natural gas sweetening | Lean MDEA feed to absorber | Lean MDEA (40‑60°C) | OH2 (316L SS) |
| Refinery HDS | Lean amine charge to absorber | Lean MDEA/DEA | OH2 (316L SS or duplex) |
| CCUS (post‑combustion capture) | Lean MEA feed to absorber | Lean MEA (40‑50°C) | OH2 (316L SS) |
| Claus tail gas treatment | Lean amine to TGTU absorber | Lean MDEA | OH2 (316L SS) |
| Syngas purification | Lean amine to CO₂ absorber | Lean MDEA | OH2 (316L SS) |
| Absorber reflux (any of above) | Condensate return to top of column | Water/amine/acid gas | OH2 (316L SS) |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours
Critical speed: ≥120% of maximum operating speed
Centreline mounting – accommodates thermal expansion (up to 80°C)
Hydrostatic test: 1.5x design pressure
Performance test: Water per API 610 Grade 2 (Grade 1 optional)
Material certification: EN 10204 3.1 full traceability
NACE MR0175 / ISO 15156 available for sour service
API 610 OH2 full compliance – 11th/12th edition ISO 13709, 20‑year life, 3‑year continuous run.
Optimised hydraulics – flow 50‑500 m³/h, head 30‑120 m covers >90% of absorber feed and reflux duties.
316L stainless steel (S‑8) standard – proven corrosion resistance in lean amine and reflux service.
Duplex option (D‑1) – for high chloride or severe sour service.
API 682 Plan 53B dual pressurised seals – zero H₂S emissions, mandatory for safety and environmental compliance.
Low NPSH design – inducer option for challenging suction conditions.
Centreline mounting – handles up to 80°C without misalignment.
Back pull‑out design – seal and bearing replacement without removing piping.
Minimum flow protection – ARC or bypass integrated.
NACE MR0175 compliant options – for sour gas sweetening units.
Field proven – thousands of OH2 pumps in gas plants, refineries, and CCUS facilities worldwide.
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (API 682 Plan 53B ready) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O‑ring kit (full set) | 1 set |
| Inducer (if fitted) | 1 set |
For detailed selection of the correct absorber feed / reflux pump for your gas sweetening, refinery, or CCUS project – including flow and head calculations, material selection (316L SS or duplex based on amine type and H₂S/chloride loading), API 682 seal plan (Plan 53B for H₂S service), and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support gas sweetening, refinery HDS, carbon capture, and syngas purification projects worldwide with reliable API 610 absorber feed and reflux pumps – corrosion‑resistant, emissions‑compliant, and built for 20‑year service.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.