Heavy Soda Filtrate Mother Liquor Pump – API 610 OH2 Radially Split Centerline Mounted Pump for High‑Temperature High‑Solids Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 heavy soda filtrate mother liquor pump for soda ash production. Radially split, centerline mounted, single‑stage overhung design. Handles mother liquor with 10‑20% suspended solids (bicarbonate crystals, salt) at 120‑180°C. Alloy cast iron or 316L stainless steel wetted parts. Abrasion‑resistant mechanical seal (silicon carbide / tungsten carbide). Back pull‑out design. Flow 50‑500 m³/h, head 40‑100 m. 20‑year design life, 3‑year continuous operation.

Conatct For Details
DetailReview(0)Additional

Product Overview

The heavy soda filtrate mother liquor pump is a specialised centrifugal pump designed for handling hot, solids‑laden mother liquor from the bicarbonate filtration stage in soda ash production (Solvay / Hou`s process). After sodium bicarbonate (NaHCO₃) crystals are separated on a rotary vacuum filter or centrifuge, the remaining liquid – called heavy soda filtrate mother liquor – is highly saturated with sodium chloride, ammonium chloride, carbonates, and contains 10‑20% suspended solids (fine bicarbonate crystals, salt particles, and other insolubles). The liquid temperature is typically 120‑180°C, and it is corrosive due to chlorides and ammonia.

This pump is classified under API 610 (ISO 13709) as Type OH2 – an overhung, centreline‑mounted, radially split, single‑stage centrifugal pump. The OH2 configuration is preferred for this service because the centreline mounting accommodates thermal expansion at high temperatures (120‑180°C), while the rugged overhung design allows easy access to the seal and bearing housing. The radially split casing provides high pressure containment and simplifies maintenance.

The pump is constructed from alloy cast iron (e.g., Ni‑Hard or high‑chromium iron) for abrasion resistance, or 316L stainless steel for corrosion resistance when chlorides are high. The mechanical seal is specially upgraded for abrasive slurry service – typically silicon carbide vs. tungsten carbide faces with external flush (Plan 32) to keep solids away from seal faces.

Construction & API 610 Classification

FeatureDescription
API 610 TypeOH2 (overhung, centreline‑mounted, radially split, single‑stage)
Casing formRadially split, centreline support feet
Bearing supportOverhung – impeller overhangs from bearing housing; bearings at drive end only
Number of stagesSingle stage
Suction typeSingle‑suction (end suction, top discharge)
Nozzle orientationAxial suction, radial discharge (top or side)

Why OH2 for Heavy Soda Filtrate Mother Liquor

  • Centreline mounting – Pump feet are cast on the casing centreline, allowing the casing to expand uniformly when handling hot liquor at 120‑180°C. This prevents shaft misalignment and bearing distress.

  • Radially split casing – The casing is split in a vertical plane perpendicular to the shaft, providing a robust pressure‑containing joint suitable for hot, corrosive fluids with solids.

  • Back pull‑out design – The complete rotating assembly (impeller, shaft, bearing housing, mechanical seal) can be removed without disconnecting suction or discharge piping – essential for pumps that require frequent seal or wear ring replacement due to solids abrasion.

  • Single‑stage simplicity – No interstage seals; wide internal passages allow solids up to 15‑20 mm to pass without clogging.

Key Technical Specifications (Heavy Soda Filtrate Mother Liquor Duty)

ParameterDesign Range
Flow rate50 – 500 m³/h (220 – 2,200 GPM)
Head40 – 100 m (130 – 330 ft)
Fluid temperature120 – 180°C (248 – 356°F)
Solids content10 – 20% by weight (fine bicarbonate crystals, NaCl, NH₄Cl)
Maximum pressure2.5 MPa (25 bar)
Speed1,450 / 2,950 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz)
NPSHrOptimised (≤5 m) – double‑suction option available
Pump efficiency65‑78% (depending on solids content and specific gravity)

Materials – Abrasion & Corrosion Resistance

The mother liquor contains solid crystals that cause erosion, plus chlorides and ammonia that cause corrosion. Material selection must balance both.

ComponentStandard MaterialUpgrade OptionRemarks
CasingAlloy cast iron (Ni‑Hard / high‑chromium)316L stainless steelAlloy iron resists abrasion; 316L resists chloride corrosion
ImpellerAlloy cast iron (hardened)316L stainless steel with hard coatingAbrasion‑resistant
Wear ringsHardened alloy ironTungsten carbide coatedExtends life in abrasive slurry
Shaft4140 hardened steel (coated)316L or duplex stainless steel–
Seal chamberAlloy cast iron or 316L316L–
Fasteners316 stainless steelDuplex–

Recommended Material by Dominant Wear Mechanism

  • High abrasion (sharp crystals, high solids) → Alloy cast iron (Ni‑Hard, hardness ≥550 BHN) – excellent erosion resistance.

  • High corrosion (chlorides > 5,000 ppm, low pH) → 316L stainless steel – resists pitting, but may require hard coating on wear rings for abrasion protection.

  • Combined severe abrasion + corrosion → Duplex stainless steel (2205) or super duplex – high strength, good corrosion resistance, and can be hardened.

For most heavy soda filtrate mother liquor duties, alloy cast iron with hardened wear rings and alloy impeller is the most cost‑effective and proven solution.

Mechanical Seal – Abrasion‑Resistant Design

Solids in the mother liquor (10‑20%) are the primary cause of mechanical seal failure. Standard carbon vs. ceramic seal faces will be destroyed rapidly.

Seal ArrangementAPI 682 PlanSuitability
Dual pressurised (Arrangement 3)Plan 53BZero emissions, but barrier fluid may not flush solids effectively – requires clean flush
Single seal with external clean flushPlan 32Highly recommended – continuous injection of clean external fluid (e.g., clarified liquor or water) at 1‑2 bar above pump suction pressure washes solids away from seal faces
Single seal with quenchPlan 62Acceptable with steam or water quench to prevent solids buildup on atmosphere side

Recommended Seal Face Materials

  • Silicon carbide vs. tungsten carbide – Extremely hard (tungsten carbide >1,800 Hv), excellent for abrasive solids.

  • Silicon carbide vs. silicon carbide – Hard, but slightly less abrasion‑resistant than tungsten carbide; acceptable for moderate solids (10‑15%).

Elastomers: Viton (FKM) or Aflas – resistant to hot ammonia, chlorides, and mild acids up to 180°C.

Important: Regardless of seal type, Plan 32 (external clean flush) is strongly recommended for mother liquor with >5% solids. The flush flow rate should be sufficient to keep solids from entering the seal chamber (typically 5‑15 L/min, depending on pump size).

Cavitation & NPSH Considerations

Hot mother liquor at 120‑180°C has high vapour pressure. Available NPSH (NPSHa) may be limited because the pump takes suction from a filter receiver or vacuum drum. To prevent cavitation:

  • Low NPSHr impeller design – Optimised inlet geometry.

  • Inducer option – Reduces NPSHr by 40‑60%; especially beneficial when NPSHa < 4 m.

  • Double‑suction first‑stage impeller (available on larger OH2 frames) – further reduces NPSHr.

  • Avoid throttling on suction side – Always control flow via discharge valve.

Abrasion Protection – Additional Features

  • Replaceable wear rings – Casing and impeller wear rings in hardened alloy or Stellite‑faced.

  • Hardened shaft sleeve – Protects shaft at seal chamber area.

  • Large internal clearances – To prevent binding from solids build‑up.

  • Easy access for cleaning – Back pull‑out design allows quick disassembly to remove solids deposits.

Applications

IndustrySpecific Service
Soda ash (Solvay / Hou`s process) | Heavy soda filtrate mother liquor return to ammonia recovery or dechlorinator |
Bicarbonate filtrationPumping filter underflow or thickener underflow with high solids
Chemical & fertilizerSlurry transfer in evaporative crystallisation processes
MiningThickener underflow with moderate abrasion

Why OH2 is the Correct Choice for This Duty

FeatureOH2 (this pump)BB1 (between‑bearings)VS4 (vertical)
Centreline mounting (hot service)Yes – essential for >120°COptionalNot applicable
Solids handlingGood (single‑stage, wide passages)GoodModerate
Maintenance without piping removalYes (back pull‑out)Yes (axial split)Yes (withdrawable)
Seal accessibilityExcellent – seal at end of shaftGoodMore complex
Suitability for 10‑20% solidsIdealSuitableLimited (vertical tends to settle solids)

The OH2 configuration is proven for hot, high‑solids mother liquor in thousands of soda ash plants worldwide.

API 610 Compliance Highlights

  • Design life: 20 years minimum

  • Continuous operation: ≥3 years uninterrupted

  • Bearing L10 life: ≥25,000 hours

  • Critical speed: ≥120% of maximum operating speed

  • Centreline mounting – accommodates thermal expansion at 120‑180°C

  • Hydrostatic test: 1.5 × design pressure

  • Performance test: Water per API 610 Grade 2 (Grade 1 optional)

  • Material certification: EN 10204 3.1 on pressure‑containing parts

Key Advantages

  • High temperature capability – Centreline mounting and robust materials handle 120‑180°C continuously.

  • High solids tolerance – 10‑20% suspended solids pass without clogging when properly maintained.

  • Abrasion‑resistant materials – Alloy cast iron (Ni‑Hard / high‑chromium) and tungsten carbide seal faces.

  • API 682 Plan 32 ready – External clean flush prolongs seal life dramatically in abrasive service.

  • Back pull‑out maintenance – Minimal downtime; replace seals, wear rings without removing piping.

  • Proven in soda ash – Thousands of units operating in bicarbonate filtration and mother liquor circuits.

  • Corrosion options – 316L stainless steel available for high‑chloride mother liquor.

Quality Assurance & Testing

  • Hydrostatic test – Casing at 1.5× MAWP.

  • Performance test – Water at rated speed per API 610 Grade 2.

  • Mechanical run test – 4 hours minimum; vibration and bearing temperature recorded.

  • Impeller dynamic balancing – Grade G6.3 or better.

  • Material certification – EN 10204 3.1 for alloy cast iron and 316L components.

  • NDE – Dye penetrant on castings; ultrasonic on shafts.

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (Plan 32 ready, tungsten carbide faces)1 set
Wear ring set (casing + impeller)1 set
Bearing set (radial + thrust)1 set
Shaft sleeve (hardened)1
Gasket / O‑ring kit (full set)1 set
Impeller (for critical duty)1 set

Get a Quote or Engineering Support

For a detailed selection of the API 610 OH2 heavy soda filtrate mother liquor pump for your soda ash plant – including flow, head, mother liquor temperature, solids percentage and composition (bicarbonate, NaCl, NH₄Cl), NPSHa, material selection (alloy cast iron vs. 316L), and API 682 seal plan (Plan 32 with tungsten carbide faces) – please contact our engineering team.

Email: info@hyrig.com

Our API 610 OH2 mother liquor pumps are specifically engineered for the most severe soda ash filtrate service – handling 10‑20% solids at 180°C with proven abrasion‑resistant seals and materials. Back pull‑out design minimises downtime, and centreline mounting ensures alignment even at extreme temperatures.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit