The cleaning liquid pump is a heavy‑duty, high‑flow centrifugal pump specifically engineered for circulating cleaning solutions, wash water, and backwash fluids in industrial plants, refineries, power stations, and manufacturing facilities. Typical services include:
CIP (clean‑in‑place) return circulation in food, beverage, pharmaceutical, and dairy plants.
Filter backwash supply for multimedia filters, sand filters, and membrane pre‑treatment.
Industrial wash water recirculation in parts washers, vehicle wash bays, and equipment cleaning stations.
Descaling and flushing circuits in steel mills and heat exchanger cleaning loops.
The pump is classified under API 610 (ISO 13709) as Type BB1 – an axially split, between‑bearings, single‑stage, single‑suction volute centrifugal pump. This configuration provides extremely high rotor rigidity, low vibration, and long bearing life, making it ideal for continuous operation at the specified flow range of 800‑2,000 m³/h and head of 40‑80 m.
The duplex stainless steel wetted parts (2205 or 2507) offer excellent resistance to chloride‑induced pitting, stress corrosion cracking, and erosion from cleaning chemicals and suspended solids. The hydraulic design is optimised for low NPSHr and cavitation resistance, allowing reliable operation even with moderate suction head. The axially split casing enables full rotor access without removing suction or discharge piping – minimising maintenance downtime.
| Feature | Description |
|---|---|
| API 610 Type | BB1 (axial split, between‑bearings, single‑stage) |
| Casing form | Horizontally split, double‑volute (standard on large sizes) |
| Bearing support | Two bearing brackets (drive end & non‑drive end) with radial and thrust bearings |
| Number of stages | Single stage |
| Suction type | Single‑suction (double‑suction first‑stage optional for lower NPSH) |
| Nozzle orientation | Side suction / side discharge or top suction / top discharge as required |
Axially split casing – The top half can be lifted without disconnecting piping, providing immediate access to the rotor, impeller, wear rings, and seal chamber. This is essential for cleaning liquid pumps that may require inspection of seal faces and impeller passages due to chemical deposits or debris.
Between‑bearings rotor – Exceptional shaft stiffness minimises deflection even at flows up to 2,000 m³/h, resulting in lower vibration and >25,000 hours bearing life.
Single‑stage design – Simple, robust, and unaffected by suspended solids or cleaning chemical residues that could foul interstage components in multistage pumps.
Double‑volute casing (on larger sizes) – Balances radial hydraulic forces over a wide operating range; extends seal and bearing life during variable flow conditions (e.g., backwash cycles).
| Parameter | Design Range |
|---|---|
| Flow rate | 800 – 2,000 m³/h (3,500 – 8,800 GPM) |
| Head | 40 – 80 m (130 – 260 ft) |
| Maximum pressure | 2.5 MPa (25 bar) |
| Liquid temperature | Up to 80°C (176°F) – higher on request |
| Liquid type | Cleaning solutions (caustic, acid, detergent), wash water, filtered backwash, CIP return, descaling fluids |
| Speed | 980 / 1,450 / 1,480 rpm (50Hz) or 1,200 / 1,800 rpm (60Hz) |
| NPSHr | ≤5 m (≤3 m with double‑suction inducer) |
| Pump efficiency | 82‑88% at BEP |
| Motor power | 250 – 800 kW (depends on specific duty) |
Cleaning liquids often contain chlorides (from detergents or make‑up water), caustic (NaOH), acids (HNO₃, H₃PO₄), and may carry abrasive particles (sand, rust, scale). Duplex stainless steel is the preferred material for its combination of high strength, excellent chloride pitting resistance (PREN >35‑40), and good erosion resistance.
| Component | Material (Standard) | Upgrade Option | API 610 Class |
|---|---|---|---|
| Casing (volute) | Duplex 2205 | Super duplex 2507 | D‑1 / D‑2 |
| Impeller | Duplex 2205 | Super duplex 2507 | D‑1 / D‑2 |
| Shaft | Duplex 2205 or 17‑4 PH | Super duplex | D‑1 / A‑8 |
| Wear rings | Duplex + Stellite hard‑facing | Tungsten carbide coating | – |
| Seal chamber | Duplex 2205 | Super duplex | D‑1 |
| Fasteners | Duplex 2205 | Super duplex | – |
Chloride resistance – Duplex (PREN 35‑40) far outperforms 316L (PREN 25‑30) in chloride‑containing cleaning solutions, preventing pitting and crevice corrosion.
High strength – Yield strength ≈ 450‑650 MPa (twice that of 316L), allowing thinner sections and lower weight.
Erosion resistance – Harder surface resists wear from suspended sand, scale, or corrosion by‑products.
Resistance to caustic and mild acids – Duplex handles typical CIP chemicals (1‑3% NaOH, 0.5‑2% HNO₃) at moderate temperatures.
All wetted parts are supplied with EN 10204 Type 3.1 material certification and positive material identification (PMI) on request.
Cleaning liquids may be hazardous, hot, or abrasive. Seal selection must ensure zero or minimal emissions and long life.
| Seal Arrangement | API 682 Plan | Suitability |
|---|---|---|
| Dual pressurised (Arrangement 3) | Plan 53B (bladder accumulator) | Recommended for toxic or high‑temperature cleaning agents; zero emissions; barrier fluid circulates |
| Single seal with external flush | Plan 32 | For abrasive cleaning liquids (sand, scale) – clean external water flushes solids away from seal faces |
| Single seal with self‑flush | Plan 11 | Only for clean, non‑hazardous cleaning liquids (e.g., warm water only) |
Plan 53B is recommended when cleaning liquids contain aggressive chemicals or when leakage cannot be tolerated.
Plan 32 is highly recommended for cleaning liquid pumps that recirculate dirty wash water or backwash effluent – an external clean water flush keeps seal faces clean and cool.
Seal faces: Silicon carbide vs. silicon carbide (hard‑on‑hard) – resists abrasion from suspended particles.
Elastomers: Viton (FKM) or Aflas – compatible with caustic, acid, and detergent solutions.
Cleaning liquid pumps often operate with limited NPSHa (e.g., pumping from a collection pit or tank with low liquid level) and may run continuously for weeks.
Optimised hydraulic design – Low NPSHr impeller inlet geometry minimises cavitation risk.
Double‑suction first‑stage impeller (option) – Cuts NPSHr by 30‑40%, ideal for low NPSHa installations.
Inducer (option) – Further reduces NPSHr to <2 metres.
Wide operating window – The pump can run continuously at any point between 60% and 110% of BEP flow without excessive vibration or cavitation.
| Industry | Specific Service |
|---|---|
| Food & beverage | CIP return circulation (caustic, acid rinse, hot water) |
| Pharmaceutical | CIP / SIP return pumps; wash water circulation for equipment cleaning |
| Refinery & petrochemical | Filter backwash pumps (media filters, carbon filters); wash water transfer |
| Power plants | Cooling water screen backwash; demineraliser regeneration flush |
| Steel & metal | Descaling spray water circulation; roll cooling water cleaning loops |
| Municipal water treatment | Filter backwash pumps for sand/anthracite filters |
| Industrial parts washing | Recirculation of heated detergent through wash cabinets |
| Feature | BB1 (this pump) | OH2 (overhung) | BB3 (multistage) |
|---|---|---|---|
| Flow range | 800‑2,000 m³/h | ≤1,000 m³/h | 50‑1,500 m³/h |
| Head range | 40‑80 m | 20‑150 m | 100‑1,500 m |
| Rotor rigidity | Very high (between‑bearings) | Moderate (overhung) | High |
| Tolerance of abrasives | Good (wide volute passages) | Fair | Poor (tight clearances) |
| Ease of maintenance without piping removal | Yes (axial split) | Yes (back pull‑out) | Partial |
| Suited for continuous high‑flow wash duty | Ideal | Limited | Over‑specified |
The BB1 configuration is the most reliable and maintainable design for high‑flow, continuous‑duty cleaning liquid services.
Design life: 20 years minimum
Continuous operation: ≥3 years uninterrupted
Bearing L10 life: ≥25,000 hours
Critical speed: ≥120% of maximum operating speed
Hydrostatic test: 1.5 × design pressure
Performance test: Water per API 610 Grade 2 (Grade 1 optional)
Material certification: EN 10204 3.1 full traceability
High flow capacity – 800‑2,000 m³/h covers large‑scale cleaning circuits.
Axial split design – Quick access for seal / impeller inspection without disturbing piping; reduces downtime.
Duplex stainless steel – Exceptional resistance to chloride pitting, caustic, and mild acids; long service life.
Cavitation‑resistant hydraulics – Low NPSHr, double‑suction option; suitable for low‑suction‑head installations.
Heavy‑duty bearings – Between‑bearings support; L10 ≥25,000 hours; low vibration.
API 682 sealing flexibility – Plan 53B (zero leakage) or Plan 32 (external flush for abrasives).
Long‑period operation – Designed for months of continuous, unattended service.
Easy spare parts availability – Common API 610 BB1 components; modular design.
Hydrostatic test – Casing and cover at 1.5× MAWP.
Performance test – Flow, head, power, efficiency per API 610 Grade 2.
Mechanical run test – 4 hours continuous; vibration and bearing temperature monitoring.
NPSH test – Optional when specified.
Non‑Destructive Examination – PT/MT on castings; UT on shaft forgings.
Material certification – EN 10204 3.1; PMI upon request.
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 53B or Plan 32 ready) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O‑ring kit (full set) | 1 set |
| Impeller (critical spare) | 1 set |
| Inducer (if fitted) | 1 set |
For a detailed selection of the API 610 BB1 cleaning liquid pump for your industrial wash, CIP, filter backwash, or cleaning circulation application – including flow, head, liquid composition, temperature, NPSHa, materials (duplex 2205 / 2507), and API 682 seal plan – please contact our engineering team.
Email: info@hyrig.com
Our API 610 BB1 cleaning liquid pumps are engineered for long‑period, cavitation‑resistant, high‑flow service in the most demanding wash and backwash duties. Duplex stainless steel construction ensures decades of corrosion‑free operation.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.