DIN Globe Valve RFQ Checklist | F1/F2, Trim & Orientation

2026-11-19 19:35

DIN Globe Valve RFQ Checklist

HYRIG can supply DIN globe valves, including standard packed and bellows seal designs. Because the standard defines multiple face-to-face series and trim options, an incomplete RFQ often leads to a valve that fits the flanges but not the piping gap, or a seat material that fails in service.

Key Facts

  • Standard: Specify BS 1873 / DIN 3230, not just "DIN globe valve".
  • Face-to-face: Specify DIN 3202 F1 or F2. DN and PN alone are not sufficient.
  • Stem seal: Specify packed or bellows seal.
  • Trim: Specify Trim 1 (Cr13), Trim 8 (Stellite), or Trim 5 (Stellite) based on medium.

Key Specifications

To receive a correctly machined valve, provide the following data in your RFQ:

Data FieldWhy It Is Needed
StandardConfirms BS 1873 / DIN 3230 as the design basis.
DNNominal size, determines bore and flange OD.
PNPressure rating, determines body thickness and face-to-face series.
Face-to-Face SeriesSpecify F1 (PN16-PN40) or F2 (PN63-PN100).
Stem SealSpecify packed or bellows seal.
Trim MaterialSpecify Trim 1, 8, or 5 based on medium and temperature.
Installation OrientationFor bellows seal, specify vertical (handwheel up).
DocumentationState if EN 10204 3.1 certificates and DIN 3230 test reports are required.

Dimensions

DimensionStandard
Face-to-face (PN16–PN40)DIN 3202 F1
Face-to-face (PN63–PN100)DIN 3202 F2
Flange drillingDIN 2543–2548 / EN 1092-1

Structure and Working Principle

The most common RFQ error is specifying the DN and PN but omitting the face-to-face series. A DN100 PN16 globe valve uses DIN 3202 F1 (350 mm), while a DN100 PN100 globe valve uses F2 (430 mm). A valve that fits the flanges may not fit the piping gap.

The second common error is omitting the trim material. Trim 1 (Cr13) is standard for non-corrosive media. Trim 8 (Stellite) or Trim 5 is required for high-temperature steam or erosive service. Using the wrong trim can lead to rapid seat wear.

The third error is omitting the installation orientation for bellows seal valves. Bellows valves should be installed vertically (handwheel up). Horizontal installation accelerates bellows wear.

Cross-Reference and Replacement

When ordering replacement DIN globe valves:

  1. Measure the existing gap: Record the face-to-face length and match it to the DIN 3202 series.
  2. Check the stem seal: Confirm whether the existing valve is packed or bellows seal, and measure the vertical clearance.
  3. Check the trim: For high-temperature or erosive service, confirm the original trim material (Cr13 vs Stellite).
  4. Verify documentation: For classified lines, specify EN 10204 3.1 certificates and DIN 3230 test reports.

Applications

  • New plant construction: Matching the line class and face-to-face series exactly.
  • Maintenance and replacement: Replacing a worn or leaking valve without modifying the piping.
  • Steam isolation: Specifying Stellite trim and correct PN rating for high-temperature service.
  • Toxic media: Specifying bellows seal and vertical orientation for zero emission.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. Gate valves are for isolation only; do not use for throttling.

Frequently Asked Questions

Q: Why do I need to specify the F-series face-to-face?

Because DIN 3202 defines different lengths for different pressure ratings. F1 is used for PN16–PN40; F2 is used for PN63–PN100.

Q: Why do I need to specify the trim material?

Trim 1 (Cr13) is standard for non-corrosive media. Trim 8 or 5 (Stellite) is required for high-temperature or erosive service to prevent rapid seat wear.

Q: What is the most important field for bellows seal valves?

The installation orientation. Bellows seal valves should be installed vertically (handwheel up) to prevent accelerated wear.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, PN rating, material, and documentation.

Selection Support

To ensure the DIN globe valve matches your piping and service, provide the DN, PN, existing gap, stem seal type, trim, and installation orientation. Our engineering team will verify the specification.

Contact

For DIN globe valve RFQ support, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment