HYRIG can supply the FESTO DFSP-50-30-PS-PA stopper cylinder. The FESTO DFSP-50-30-PS-PA is a single-acting pulling stopper cylinder with a 50 mm piston diameter, 30 mm stroke, and elastic end-position cushioning. It delivers a 6280 N impact force and tolerates 1570 N lateral force during switching, operating from 1.2 bar to 10 bar. It is used on conveyor and roller lines to block, separate, or position workpieces, and the built-in magnet allows piston position sensing with proximity switches.
| Cylinder type | Stopper cylinder, DFSP series |
| Piston diameter | 50 mm |
| Stroke | 30 mm |
| Mode of operation | Single-acting, pulling |
| Cushioning | Elastic, both ends (PA) |
| Operating pressure | 1.2 bar … 10 bar |
| Impact force | 6280 N |
| Permissible lateral force during switching | 1570 N |
| Max. cycle frequency | 5 Hz |
| Pneumatic connection | G1/8 |
| Position detection | For proximity switch (built-in magnet) |
| Weight | 1.2 kg |
| Order code | 576152 |
| Model | Bore | Stroke | Impact force | Lateral force | Weight | Order code |
|---|---|---|---|---|---|---|
| DFSP-50-30-PS-PA | 50 mm | 30 mm | 6280 N | 1570 N | 1.2 kg | 576152 |
| DFSP-20-15-PS-PA | 20 mm | 15 mm | 1370 N | 228 N | 0.22 kg | 576079 |
Explore the full range in the FESTO DFSP stopper cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Piston diameter | 50 mm |
| Stroke | 30 mm |
| Pneumatic connection | G1/8 |
| Mounting type | Through-hole, female thread, or accessories |
| Corrosion resistance class | KBK 2 (moderate) |
| Ambient temperature | -10 °C … +80 °C |
| Weight | 1.2 kg |
| Seals material | TPE-U(PU) |
| Piston rod material | High-alloy stainless steel |
| Cylinder tube material | Wrought aluminium alloy, smooth anodised |
The DFSP series is a single-acting pulling stopper cylinder. Compressed air enters the port and retracts the piston rod, pulling the stopper lever or gate out of the workpiece path. When the air is exhausted, a mechanical spring extends the rod and returns the stopper to the blocking position. The elastic cushioning at both ends absorbs the impact when the stopper extends into the path of a moving workpiece.
The 50 mm bore delivers a 6280 N impact force, which is the maximum force the stopper can withstand when a workpiece hits it. The permissible lateral force during switching is 1570 N — this is the side load the stopper lever can tolerate while moving into position. The 5 Hz maximum cycle frequency limits how often the stopper can be actuated per second. The built-in magnet allows the piston position to be detected with standard FESTO proximity switches, so the control system can confirm whether the stopper is fully extended or retracted.
Replacing a stopper cylinder on a conveyor line with the DFSP-50-30-PS-PA? Check these five points:
For a broader replacement checklist, see the FESTO stopper cylinder replacement guide.
Not sure whether the 6280 N impact force and 1570 N lateral force cover your conveyor load, or need the smaller 20 mm bore for a lighter application? Send your workpiece weight, conveyor speed, required cycle rate, supply pressure, and stopper lever geometry, and we will confirm the bore size and sensor configuration.
Q: What is the impact force of the Festo DFSP-50-30-PS-PA?
A: 6280 N, which is the maximum force the stopper can withstand when a workpiece hits it.
Q: What is the permissible lateral force during switching?
A: 1570 N, which is the side load the stopper lever can tolerate while moving into position.
Q: Is the DFSP-50-30-PS-PA single-acting or double-acting?
A: Single-acting, pulling. Compressed air retracts the piston rod; a mechanical spring extends it back to the blocking position when the air is exhausted.
Q: Does the DFSP-50-30-PS-PA have a built-in magnet for position sensing?
A: Yes. The cylinder is equipped with a built-in magnet, and the piston position can be detected with standard FESTO proximity switches. Confirm the sensor output type (PNP or NPN) before ordering.
Q: What is the lead time for Festo DFSP-50-30-PS-PA?
A: Standard lead time is 7–17 days from order confirmation, based on the quoted supply status.
For FESTO DFSP-50-30-PS-PA selection and sensor configuration, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.