Festo Pneumatic Cylinders | ISO 15552, Compact, Round, Guided

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO pneumatic cylinder range, covering ISO 15552 profile and tie-rod cylinders, ISO 21287 compact cylinders, ISO 6432 round cylinders, and guided drives. This overview groups the main cylinder families by body type and application, so you can match the cylinder to the available space, the required force, and the load guidance needs. Specific models and dimensions are covered on the individual model pages.
Conatct For Details
DetailReview(0)Additional

Festo Pneumatic Cylinders | ISO 15552, Compact, Round, Guided

HYRIG can supply the FESTO pneumatic cylinder range. This overview groups the main cylinder families by body type and application, so you can match the cylinder to the available space, the required force, and the load guidance needs. Specific models and dimensions are covered on the individual model pages.

Key Facts



Cylinder familiesISO 15552 profile (DSBC), ISO 15552 tie-rod (DSBG), ISO 21287 compact (ADN/ADVU/ADVUL), ISO 6432 round (DSNU), guided (DFM), mini slide (DGST)
Bore range10 mm … 320 mm across families
Force range at 6 bar47 N … 48255 N
Cushioning optionsAdjustable pneumatic (PPVA/PPV-A), self-adjusting (PPSA), elastic (P-A)
Position sensingMagnetic piston and sensor slots on most families

Cylinder Family Comparison

FamilyStandardBody typeTypical bore rangeBest for
DSBCISO 15552Profile barrel32–320 mmGeneral automation, DNC replacement, long strokes
DSBGISO 15552Tie-rod profile32–320 mmServiceable tie-rod design, existing DNC footprint
ADNISO 21287Compact12–80 mmTight spaces, short strokes, clamping
ADVUISO 21287Compact20–63 mmLonger strokes in a compact body
ADVULISO 21287Compact anti-rotation32–40 mmLoads that must not rotate
DSNUISO 6432Round8–25 mmLight-duty ejection, small clamps
DFM—Guided drive10–63 mmPress-fit, lift, side-load applications
DGST—Mini slide6–25 mmCompact pick-and-place, short transfer

Data source: Technical data table.

Selecting the Right Cylinder Family

Start with the mounting interface: if the machine already uses an ISO 15552 bracket, the DSBC or DSBG is the direct choice. If the available space is tight and the stroke is short, the ADN compact family fits where an ISO 15552 cylinder cannot. If the load must not rotate, the ADVUL anti-rotation compact or the DFM guided drive provides the necessary guidance.

Next, confirm the force and cushioning. The theoretical force depends on the bore and the supply pressure. The cushioning choice — adjustable (PPVA/PPV-A), self-adjusting (PPSA), or elastic (P-A) — determines whether the deceleration can be tuned to the load. For high-cycle applications with varying loads, adjustable cushioning is preferred; for simple, low-cost applications, elastic cushioning may be sufficient.

Selection Support

Not sure which cylinder family matches your existing machine or your new design? Send the mounting interface, available space, required force, stroke, and load guidance requirement, and we will confirm the family, bore, and cushioning variant. Explore the Festo DSBC ISO 15552 cylinder overview for the profile range, or the Festo ADN compact cylinder overview for the compact range.

Frequently Asked Questions

Q: What is the main difference between DSBC and ADN cylinders?
A: DSBC is an ISO 15552 profile cylinder for general automation and longer strokes. ADN is an ISO 21287 compact cylinder for tight spaces and short strokes. The mounting interfaces and body dimensions differ.

Q: When should I choose a guided cylinder instead of a standard cylinder?
A: Choose a guided cylinder (DFM) when the load introduces side forces or torque that would bend a standard piston rod, or when the load must follow a precise linear path without rotation.

Q: What is the difference between PPVA and PPSA cushioning?
A: PPVA is adjustable pneumatic cushioning with a tuning screw. PPSA is self-adjusting pneumatic cushioning without a tuning screw — it adapts to the load automatically.

Q: Can I replace a DNC cylinder with a DSBC?
A: Mechanically yes on the ISO 15552 interface, but verify cushioning type, port thread, and sensor slot geometry. See the DNC to DSBC replacement guide for the full checklist.

Q: What is the smallest bore in the FESTO cylinder range covered here?
A: The DSNU round cylinder starts at 8 mm bore; the DGST mini slide starts at 6 mm bore. The smallest bore with an ISO standard is the 32 mm DSBC/DSBG.

Contact

For FESTO pneumatic cylinder family selection and model code confirmation, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit