Festo Rodless Drive Replacement | DGPL Checklist

2026-11-08 23:57

Festo Rodless Drive Replacement | DGPL Checklist

HYRIG can supply DGPL rodless linear drives as replacements for existing rodless pneumatic actuators. This guide explains the five checkpoints that determine whether a Festo DGPL is a mechanical drop-in replacement, and where the configured interface may still differ. It covers stroke, guide type, lateral force, operating pressure, and mounting interface.

Why Rodless Drive Replacement Is Not Just Stroke

A rodless drive uses a carriage that moves along the profile barrel, with a recirculating ball bearing guide for stiffness and load capacity. The absence of a piston rod means the overall length is close to the stroke plus the end caps, which is the main reason to choose a rodless drive over a piston-rod cylinder. Two rodless drives with the same stroke can still differ in the guide type, the permissible lateral force, the operating pressure range, and the carriage hole pattern, so those details must be checked before the replacement can be installed.

Five-Point Replacement Checklist

1. Stroke

Confirm that the DGPL stroke matches the existing travel. The DGPL-25 is available in 170 mm and 270 mm strokes; if the existing stroke is different, a different DGPL variant is required.

2. Guide Type

The DGPL series uses a recirculating ball bearing guide (KF). If the existing drive uses a plain-bearing guide, the KF guide provides higher stiffness and load capacity but is more sensitive to contamination. Confirm that the environment is suitable for a ball bearing guide.

3. Lateral Force

Confirm the permissible lateral force during switching. The DGPL-25 has a 147 N limit. If the load introduces higher side forces, an external guide may be required.

4. Operating Pressure

Confirm that the supply pressure is within the DGPL range of 2-8 bar. This is narrower than a standard cylinder (0.6-12 bar); if the supply can drop below 2 bar, the DGPL may not operate reliably.

5. Mounting Interface

Compare the carriage hole pattern and the guide rail mounting with the existing fixture. The DGPL footprint may not match other rodless drive brands without an adapter plate.

Common Field Errors

  • Assuming all rodless drives with the same stroke are interchangeable. The guide type and the carriage hole pattern can differ between brands and series.
  • Ignoring the 2 bar minimum pressure. The DGPL requires at least 2 bar to operate; if the supply can drop below that, the drive may not move reliably.
  • Exceeding the lateral force limit. The 147 N limit is the permissible lateral force during switching; higher side loads require an external guide.

Selection Support

Not sure which DGPL rodless drive replaces your existing unit? Send the existing drive model number, the stroke, the guide type, the lateral force, the supply pressure, the carriage drawing, and the sensor requirement, and we will confirm the DGPL model and any adapter required. Explore the Festo DGPL rodless linear drive overview.

Frequently Asked Questions

Q: Is a Festo DGPL a direct replacement for any rodless drive?
A: No. The stroke, guide type, lateral force, operating pressure, and mounting interface must be verified before treating it as a drop-in replacement.

Q: What is the operating pressure range of the DGPL?
A: 2 bar to 8 bar, narrower than a standard cylinder. Confirm that the supply pressure is within this range.

Q: What is the permissible lateral force during switching?
A: 147 N for the DGPL-25. If the load introduces higher side forces, an external guide may be required.

Q: Does the DGPL have adjustable cushioning?
A: Yes. The PPV-A suffix indicates adjustable pneumatic cushioning at both ends.

Q: What is the lead time for Festo DGPL rodless drive replacements?
A: Standard lead time is 7-8 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO DGPL rodless drive replacement verification, contact HYRIG: info@hyrig.com.

Related Pages

Name:
Message:
Verification code:
Submit
Comment