Festo Stopper Cylinder Replacement | DFSP Checklist

2026-11-08 23:53

Festo Stopper Cylinder Replacement | DFSP Checklist

HYRIG can supply DFSP stopper cylinders as replacements for existing conveyor stopper cylinders. This guide explains the five checkpoints that determine whether a Festo DFSP is a mechanical drop-in replacement, and where the configured interface may still differ. It covers impact force, lateral force, stroke, operating pressure, and position sensing.

Why Stopper Cylinder Replacement Is Not Just Stroke

A stopper cylinder is a single-acting pulling cylinder with a spring return. The impact force is the maximum force the stopper can withstand when a moving workpiece hits it, and the lateral force is the side load the stopper lever can tolerate during switching. Two stopper cylinders with the same stroke can still differ in the impact force rating, the lateral force rating, the spring return behaviour, and the position sensing option, so those details must be checked before the replacement can be installed.

Five-Point Replacement Checklist

1. Impact Force

Confirm that the DFSP impact force rating covers the maximum workpiece weight and conveyor speed. The 20 mm bore is rated at 1370 N; the 50 mm bore is rated at 6280 N. If the existing application produces a higher impact force, a larger bore is required.

2. Lateral Force

Confirm that the side load on the stopper lever during switching is within the DFSP rating. The 20 mm bore tolerates 228 N; the 50 mm bore tolerates 1570 N. Higher side loads may damage the guide or the lever.

3. Stroke

The DFSP-20 has a 15 mm stroke; the DFSP-50 has a 30 mm stroke. Confirm that the stopper lever travel matches the stroke.

4. Operating Pressure

Confirm that the supply pressure is within the DFSP range. The 20 mm bore requires at least 1.6 bar; the 50 mm bore requires at least 1.2 bar. The maximum pressure is 10 bar for both.

5. Position Sensing

The DFSP has a built-in magnet, so the piston position can be detected with standard FESTO proximity switches. Confirm the sensor output type (PNP or NPN) and the sensor mounting slot before ordering.

Common Field Errors

  • Ignoring the impact force rating. The stopper must be sized for the maximum workpiece weight and conveyor speed, not the average.
  • Assuming the lateral force limit is the same for all bores. The 20 mm bore tolerates only 228 N during switching, compared with 1570 N for the 50 mm bore.
  • Forgetting the spring return. The DFSP is single-acting; if the existing cylinder is double-acting, the control logic must be adjusted.

Selection Support

Not sure which DFSP stopper cylinder replaces your existing unit? Send the existing stopper model number, the workpiece weight, the conveyor speed, the stopper lever geometry, the supply pressure, and the sensor requirement, and we will confirm the DFSP model and any adapter required. Explore the Festo DFSP stopper cylinder overview.

Frequently Asked Questions

Q: Is a Festo DFSP a direct replacement for any stopper cylinder?
A: No. The impact force, lateral force, stroke, operating pressure, and position sensing must be verified before treating it as a drop-in replacement.

Q: What is the difference between DFSP-20 and DFSP-50?
A: The 20 mm bore delivers 1370 N impact force and tolerates 228 N lateral force. The 50 mm bore delivers 6280 N impact force and tolerates 1570 N lateral force.

Q: Is the DFSP single-acting or double-acting?
A: Single-acting, pulling. Compressed air retracts the piston rod; a mechanical spring extends it back to the blocking position.

Q: Does the DFSP have a built-in magnet for position sensing?
A: Yes. The cylinder is equipped with a built-in magnet, and the piston position can be detected with standard FESTO proximity switches.

Q: What is the lead time for Festo DFSP stopper cylinder replacements?
A: Standard lead time is 7-17 days from order confirmation, based on the quoted supply status.

Contact

For FESTO DFSP stopper cylinder replacement verification, contact HYRIG: info@hyrig.com.

Related Pages

Name:
Message:
Verification code:
Submit
Comment