HYRIG can supply the FESTO VSVA-B-B52-H-A1-1R5L solenoid valve. The FESTO VSVA-B-B52-H-A1-1R5L is a 5/2 bistable directional control valve with a standard nominal flow rate of 1100 l/min, a 26 mm valve width to ISO 15407-1, and two 24 VDC solenoids with an M12 central plug. It is used where the valve must hold its last position on power loss — bistable operation means the spool stays where it was last shifted, without a spring return.
| Valve function | 5/2 bistable |
| Standard nominal flow rate | 1100 l/min |
| Maximum flow rate | 1400 l/min |
| Valve width | 26 mm (ISO 15407-1) |
| Operating pressure | 3 bar … 8 bar |
| Supply voltage | 24 VDC |
| Electrical connection | M12 central plug, round design |
| Protection class | IP65 |
| Reset method | Bistable, no spring return |
| Weight | ~266 g |
| Order code | 534557 |
| Model | Function | Flow rate | Width | Pressure range | Order code |
|---|---|---|---|---|---|
| VSVA-B-B52-H-A1-1R5L | 5/2 bistable | 1100 l/min | 26 mm | 3-8 bar | 534557 |
| VSVA-B-M52-MZD-A1-1T1L | 5/2 monostable | 1100 l/min | 26 mm | -0.9-10 bar | 539159 |
| VSVA-B-T32C-AH-A1-1R5L | 2×3/2 NC monostable | 900 l/min | 26 mm | 3-8 bar | 534552 |
Explore the full range in the FESTO VSVA valve terminal overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Valve width | 26 mm |
| Pneumatic connection | Sub-base, 26 mm to ISO 15407-1 |
| Electrical connection | M12 central plug |
| Supply voltage | 24 VDC |
| Protection class | IP65 |
| Weight | ~266 g |
| Operating temperature | -5 °C … +50 °C |
| Media | Compressed air to ISO 8573-1:2010 [7:4:4] |
The VSVA-B-B52-H-A1-1R5L is a 5/2 bistable piston spool valve with two solenoids and no spring return. A momentary signal on the set solenoid shifts the spool to connect port 1 to port 4 and port 2 to port 3; a momentary signal on the reset solenoid shifts the spool back. When both solenoids are de-energized, the spool stays in its last position — the valve holds the actuator position on power loss.
The bistable function is useful where a cylinder must stay extended or retracted when the control power is lost, without adding a separate pilot-operated check valve or a mechanical lock. The 26 mm width provides a 1100 l/min flow rate, and the maximum flow rate is 1400 l/min. The M12 central plug carries both solenoid signals and the LED status indicators.
Not sure whether bistable or monostable is the correct function for your holding requirement, or need the matching 18 mm VSVA-B slice? Send your actuator type, required position on power loss, flow requirement, and manifold width, and we will confirm the valve function and flow rating.
Q: What is the flow rate of the Festo VSVA-B-B52-H-A1-1R5L?
A: 1100 l/min standard nominal flow rate, with a maximum flow rate of 1400 l/min.
Q: What is the difference between bistable and monostable VSVA valves?
A: A bistable valve has two solenoids and no spring; it holds its last spool position when both solenoids are de-energized. A monostable valve has a spring return that moves the spool to a defined position when the solenoid is de-energized. Choose bistable when the actuator must hold position on power loss; choose monostable when a defined fail-safe position is required.
Q: Does the VSVA-B-B52-H-A1-1R5L require continuous solenoid power to hold position?
A: No. Bistable operation means the spool stays in its last position without continuous power. A momentary pulse on the set or reset solenoid is sufficient to change position.
Q: Does the VSVA-B-B52-H-A1-1R5L use the same 26 mm manifold as the monostable variant?
A: Yes. It uses the 26 mm ISO 15407-1 sub-base. Confirm the function-specific port pattern before mixing bistable and monostable slices on one manifold.
Q: What is the lead time for Festo VSVA-B-B52-H-A1-1R5L?
A: Standard lead time is 4–5 weeks from order confirmation, based on the quoted supply status.
For FESTO VSVA-B-B52-H-A1-1R5L selection and manifold configuration, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.