OH1 Pump Project Cases – Refinery, Power Plant, Desalination & Petrochemical Success Stories

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Four OH1 pump successful cases. Case 1: Refinery process transfer – API 610 OH1 pumps for distillation unit circulation, 3 years failure-free, high efficiency. Case 2: Power plant cooling water – large-flow OH1 with double volute, stable operation, low vibration, easy maintenance. Case 3: Seawater desalination – duplex steel OH1 for seawater feed, corrosion-resistant, 24/7 continuous service. Case 4: Petrochemical amine service – 316L OH1 with API 682 seal, handles corrosive amine, long seal life. We provide site photos, P&ID reference, and performance data for each installation.

Conatct For Details
DetailReview(0)Additional

This page presents verified field cases of our API 610 OH1 horizontal single-stage overhung foot-mounted pumps operating reliably in general process, cooling water, seawater, and corrosive chemical services. Each case demonstrates the pump's back pull-out convenience, high efficiency, and long-term reliability.


Case 1 – Refinery Process Transfer (Southeast Asia)

Background: A refinery required reliable pumps for distillation unit circulation service. Operating conditions: clean hydrocarbon streams, moderate temperature, continuous 24/7 duty.

OH1 Pump Solution:

  • Flow: 450 m³/h

  • Head: 95 m

  • Temperature: 150°C

  • Material: Carbon steel casing, 316L impeller

  • Seal: API 682 Plan 11 mechanical seal

Results:

  • 3 years of failure-free operation with only routine maintenance

  • High efficiency (84%) at duty point – measured energy savings

  • Back pull-out design allowed quick seal replacement during turnaround (piping remained connected)

  • Vibration levels consistently below 2.0 mm/s

Available references: Site photo, performance log, maintenance record.


Case 2 – Power Plant Cooling Water (Asia)

Background: A 300 MW power plant needed large-flow cooling water circulation pumps with stable operation, low vibration, and easy maintenance access.

OH1 Pump Solution:

  • Flow: 2,200 m³/h

  • Head: 28 m

  • Speed: 990 rpm (low speed for large flow)

  • Casing: Double volute (to balance radial thrust at off-peak flows)

  • Material: Cast iron casing, bronze impeller

Results:

  • Stable operation across seasonal load variations (50–100% plant output)

  • Low vibration – double volute eliminated radial thrust imbalance

  • Easy maintenance – back pull-out design without disturbing large-diameter piping

  • Energy efficient (89%) – reduced pumping cost by 6%

Available references: Installation photo, vibration data log, efficiency curve.


Case 3 – Seawater Desalination (Middle East)

Background: A seawater reverse osmosis (SWRO) desalination plant required a corrosion-resistant feed pump for raw seawater intake. Chloride concentration exceeded 35,000 ppm.

OH1 Pump Solution:

  • Flow: 850 m³/h

  • Head: 45 m

  • Material: Duplex stainless steel (casing, impeller, shaft)

  • Seal: API 682 Plan 53B dual mechanical seal with seawater-compatible faces

  • Coating: External epoxy for marine environment

Results:

  • 24/7 continuous service for 2+ years without corrosion or pitting

  • Duplex material provided excellent resistance to chloride attack

  • Low NPSH design handled seawater lift conditions

  • No seal failures – dual seal with barrier fluid protected against ingress

Available references: Site photos, material certificate (EN 10204 3.1), operating report.


Case 4 – Petrochemical Amine Service (North America)

Background: A gas plant required amine circulation pumps for H₂S removal. Amine service is challenging due to high temperature, foaming potential, and need for zero leakage.

OH1 Pump Solution:

  • Flow: 320 m³/h

  • Head: 110 m

  • Temperature: 110°C

  • Material: 316L stainless steel (casing, impeller, shaft)

  • Seal: API 682 Plan 53B dual cartridge mechanical seal

Results:

  • Long seal life – over 18 months on original seals

  • Handled corrosive rich/lean amine without pitting or stress corrosion cracking

  • Zero leakage to atmosphere – dual seal with barrier fluid contained amine safely

  • Back pull-out design allowed quick impeller inspection without breaking piping

Available references: P&ID, seal flush plan diagram, site photo.


What You Can Request From Us for Each Case

  • Site photos and installation images

  • Project parameter sheet (flow, head, material, seal, temperature)

  • Actual operating data (vibration, bearing temperature, power consumption)

  • P&ID reference (where available)

  • User reference contact (with prior permission)

Why Real Project Cases Matter

Field references prove that our OH1 pumps deliver:

  • 3+ years failure-free operation in refinery process service

  • Stable, low-vibration performance in large-flow cooling water (double volute advantage)

  • Corrosion-resistant 24/7 service in seawater desalination (duplex)

  • Long seal life in corrosive amine service (API 682 dual seals)

Get the Complete OH1 Pump Case Study Package

We can match your operating conditions to similar successful installations. Request the OH1 pump project case PDF or ask for references in your specific industry.

Email: info@hyrig.com

Please specify your industry (refinery / power / desalination / petrochemical) and we will send relevant case studies, photographs, and technical data within 24 hours. We also welcome inquiries for custom OH1 pump selection and factory direct pricing for general process applications.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit