The OH3 pump is an API 610 vertical overhung cantilever sump pump, specifically designed for tank sump and pit installation. Its most distinctive feature is the absence of a submerged bearing – a design innovation that eliminates the most common failure mode in conventional sump pumps. Below we compare the OH3 against horizontal pumps (OH1/OH2) and vertical multistage (VS) pumps to help you select the right pump for your sump, pit, or low-level liquid pumping application.
Core Advantages of OH3 Pump
No Submerged Bearing → Greatly Reduce Underwater Failure & Maintenance
The only bearings are located above the mounting plate, completely isolated from the pumped liquid. Sand, sludge, corrosives, and hot fluids cannot damage bearings. This eliminates the #1 cause of sump pump failure and extends maintenance intervals dramatically.
Vertical Cantilever Design → Suitable for Deep Sump and Tank Installation
The long cantilever shaft reaches down to the impeller without any intermediate bearings. Sump depths from 500 mm to 3,000+ mm are standard. No alignment issues, no stuck bearings, no submerged components.
No Underwater Mechanical Seal → Lower Leakage Risk
Unlike submerged pumps that require a shaft seal below the liquid surface, the OH3 has no dynamic seal under the liquid. This greatly reduces leakage risk – critical for oily water, chemical sumps, and environmental compliance.
Compact Structure, Easy Installation on Tank Top or Pit Edge
The pump mounts vertically via a support plate. No large foundation required. Ideal for tight areas, tank top mounting, and retrofit projects.
Good Anti-Vibration Performance, Stable Long-Term Operation
The rigid cantilever shaft and heavy-duty upper bearing housing provide excellent stability. Vibration is minimal even at full speed and deep sump depths.
OH3 vs OH1 / OH2 (Horizontal Overhung Pumps)
| Feature | OH3 | OH1 / OH2 |
|---|---|---|
| Orientation | Vertical | Horizontal |
| Mounting | Tank top / pit edge | Floor / baseplate |
| Suitable for sump/pit | Excellent (designed for it) | Poor (needs flooded suction) |
| Submerged bearing | None | N/A (horizontal) |
| Leakage risk | Very low (no submerged seal) | Moderate (shaft seal at liquid end) |
| Footprint | Small (vertical) | Larger (horizontal with baseplate) |
Verdict: Use OH3 when pumping from a sump, pit, tank side, or any low-level liquid where horizontal pumps cannot self-prime or require flooded suction. Use OH1/OH2 for standard horizontal process pumping above ground.
OH3 vs VS Pump (Vertical Multistage Sump / Deep Well Pump)
| Feature | OH3 | VS Pump |
|---|---|---|
| Configuration | Single-stage cantilever | Multistage (multiple bowls) |
| Bearings | No submerged bearings (above plate) | Multiple submerged bearings (bowl bearings) |
| Maintenance | Easy – pull shaft from above | Complex – must pull column and bowls |
| Cost | Lower (simpler construction) | Higher (many stages, complex) |
| Head range | Low to medium (up to 160 m) | High to very high (up to 600+ m) |
| Best for | Sump drainage, low-level recovery | Deep wells, high head water supply |
Verdict: Choose OH3 for shallow to medium sump depth (≤3 m), low to medium head, and applications where reliability (no submerged bearings) is critical. Choose VS pump for deep wells, high head requirements, or when multistage pressure is needed.
Best Applications for OH3 Pump
Sump tank (refinery, chemical, power plant)
Pit drainage (underground pits, containment basins)
Oily water recovery (API separators, drain sumps)
Low-level liquid pumping (tank bottom emptying, low NPSH)
Wastewater lift stations (where solids are minimal)
Any application requiring a vertical cantilever pump without submerged bearings
Get an OH3 Pump vs OH1/OH2/VS Comparison for Your Duty
Not sure whether OH3, horizontal pump, or VS pump is best for your sump application? Our engineering team provides free pump selection advisory.
Send us your duty point:
Flow rate (m³/h or GPM)
Total head (m or ft)
Sump depth (mm or inches)
Fluid (oily water, chemical, clean water, etc.)
Any solids or temperature requirements
We will reply within 24 hours with:
Recommended pump type (OH3, OH1/OH2, or VS)
Side-by-side comparison for your specific duty
Performance curve and API data sheet
Sump installation drawing (2D CAD)
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1, OH2, OH3, BB1, BB2, BB3, BB4, BB5, VS types) serving global refineries, petrochemical plants, chemical facilities, power utilities, and wastewater treatment systems. Contact us for custom-engineered OH3 sump pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.