OH3 Pump Technical Specifications – API 610 Vertical Cantilever Sump Pump for Refinery, Chemical & Wastewater

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
OH3 pump API 610 vertical overhung cantilever sump pump technical specifications. Performance: flow 3–1800 m³/h, head 5–160 m, speed 1480/2980 rpm, temperature -20°C to 280°C, max pressure 16 bar, sump depth customizable 500–3000mm. Structure: vertical cantilever, no submerged bearing (only upper bearing), long cantilever alloy steel shaft, closed/semi-open impeller, vertical volute casing. Options: strainer, vortex breaker, cooling jacket. Materials: cast iron/carbon steel/316L/duplex casing; 304/316L/duplex/high chrome impeller; forged stainless/alloy steel shaft. Documents: API data sheet, sump installation drawing, performance curve, 3D model, material certificate.

Conatct For Details
DetailReview(0)Additional

This page provides complete technical parameters for our OH3 API 610 vertical overhung cantilever sump pump. The OH3 is designed with no submerged bearing, making it the most reliable choice for sump tank, pit, and wastewater pumping in refineries, petrochemical plants, chemical facilities, and industrial drainage systems.


Performance Range

ParameterValue
Flow rate3 ~ 1,800 m³/h (13 ~ 7,900 GPM)
Total head5 ~ 160 m (16 ~ 525 ft)
Speed1480 / 2980 rpm (50/60 Hz)
Medium temperature-20°C ~ +280°C (-4°F ~ +536°F) – higher with special materials
Maximum working pressureUp to 16 bar (232 psi)
Sump depthCustomizable: 500 mm ~ 3,000 mm (longer on request)

Structural & Mechanical Design

  • Type: Vertical overhung cantilever sump pump (API 610 OH3 designation)

  • Installation: Vertical tank or sump pit mounted – support plate rests on concrete or steel structure

  • Bearing: Only upper bearing assembly (no submerged bearing) – completely above the liquid, eliminating bearing contamination and failure

  • Shaft: Long cantilever alloy steel shaft – no intermediate bearings, transfers torque directly to impeller

  • Impeller: Closed (clean liquids) or semi-open (slight solids) – single suction

  • Casing: Vertical volute structure – optimized hydraulics for sump pumping

  • Optional features: Suction strainer (debris protection), vortex breaker (air entrainment prevention), cooling jacket (high temperature service)


Material Options

ComponentStandard MaterialsUpgrade Options
CasingCast iron, carbon steel, 316L stainless steelDuplex, super duplex
Impeller304, 316L stainless steelDuplex, high chrome alloy (for abrasion)
ShaftForged stainless steel (316L) or alloy steel (4140)Duplex, K500
Liner & bushingsAnti-corrosion wear-resistant alloyColmonoy-coated, Stellite

Key Design Features Explained

No Submerged Bearing
Conventional vertical sump pumps often have bearings submerged in the pumped liquid. These bearings fail quickly when liquids are dirty, corrosive, or hot. The OH3 has bearings located above the mounting plate – completely out of the liquid. This eliminates the #1 cause of sump pump failure and dramatically extends maintenance intervals.

Long Cantilever Shaft
The shaft extends from the upper bearing housing down to the impeller without any intermediate supports. This allows sump depths up to 3 meters (or longer) without alignment issues or submerged bearings. Dry-run resistant design available.

Back Pull-Out Maintenance
The entire rotating assembly (shaft, impeller, bearing housing) can be removed from above without draining the sump or disconnecting the discharge piping. Maintenance is fast and safe.

No Shaft Seal Below Liquid
Because there is no seal submerged in the liquid, leakage risk is virtually eliminated – critical for environmental compliance in oily water or chemical sumps.


Available Technical Documents (Free Request)

  • API 610 data sheet (filled with your operating conditions)

  • Sump installation drawing (2D CAD, PDF/DWG) – including mounting flange and sump depth dimensions

  • Performance curve (head, efficiency vs flow)

  • 3D model (STEP/IGES for plant layout)

  • Material certificate (EN 10204 3.1 or 3.2)


Typical Applications

  • Refinery sump recovery – oily water collection, drain sumps

  • Chemical tank liquid transfer – containment pits, spill basins

  • Pit drainage – underground pits in petrochemical plants

  • Wastewater treatment – lift stations, clarifier sumps

  • Plant oily water collection – API separator sumps

  • Low-level medium pumping – tank bottom drainage


Get Your OH3 Pump Technical Specification Package

To request a complete documentation package with a formal quotation, please send us your operating conditions:

  • Flow rate (m³/h or GPM)

  • Total head (m or ft)

  • Sump depth (mm or inches)

  • Fluid name and temperature (°C)

  • Any solid content or corrosivity information

Our engineering team will respond within 24 hours with:

  • Recommended OH3 pump model (size, impeller trim, material)

  • Performance curve PDF

  • API 610 data sheet

  • Sump installation drawing (2D CAD) and 3D model link

  • Factory direct price (EXW / FOB / CIF)

Email: info@hyrig.com

We are a professional API 610 pump manufacturer (OH1, OH2, OH3, BB1, BB2, BB3, BB4, BB5, VS types) serving global refineries, petrochemical plants, chemical facilities, and wastewater treatment systems. Contact us for custom-engineered OH3 sump pumps at factory direct wholesale pricing.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit