The OH5 pump is an API 610 horizontal overhung pump with integral gear drive, specifically designed for high speed, low flow, high head process duties where standard OH1 or OH2 pumps cannot achieve the required head due to speed limitations. By integrating a gearbox into the pump housing, the OH5 operates at 3,000–6,000+ rpm, delivering heads up to 450+ meters with a single stage. Below we compare the OH5 against OH1/OH2 and BB type pumps to help you select the right pump for high speed, low flow applications.
Core Advantages of OH5 Pump
Integral Gear Drive → Realize High Speed Without External Speed Increaser
The built-in gearbox steps up the input speed, allowing the impeller to spin at 3,000–6,000+ rpm (or higher). No separate gearbox, no coupling alignment, no high-speed motor required. Factory pre-aligned unit reduces on-site installation error.
Monoblock Compact Structure → Save Layout Space, Easy Skid Mounting
The pump, gearbox, and bearing housing are integrated into a single unit. Footprint is up to 50% smaller than conventional pump + gearbox + baseplate. Ideal for offshore platforms, retrofit projects, and modular skids.
Back Pull-Out Design → Easy Maintenance Without Pipe Removal
The entire rotating assembly (impeller, shaft, bearings, seal) can be removed from the rear while the casing and piping remain in place. Gearbox service can also be performed without removing the pump casing.
Perfect for Low Flow High Head Working Conditions
At a typical OH1/OH2 speed of 2,980 rpm, achieving 400+ meters head would require multiple stages (BB3/BB4). The OH5 achieves the same head with a single high-speed impeller, reducing complexity and cost.
Factory Pre-Aligned Unit → Reduce On-Site Installation Error
The pump and gearbox are aligned at the factory. Simply bolt the unit to your baseplate, connect the motor via a flexible coupling (or mount the motor directly on the unit), and you are ready to run.
OH5 vs OH1 / OH2 (Direct Motor Drive, Normal Speed)
| Feature | OH5 (Integral Gear Drive) | OH1 / OH2 (Direct Drive) |
|---|---|---|
| Speed | 3,000 – 12,000+ rpm (gear increased) | 1,480 / 2,980 rpm (motor speed) |
| Head capability at low flow | High (450+ m with single stage) | Limited (typically <150 m at low flow) |
| Flow range | Low to medium (2–800 m³/h) | Up to 2,600 m³/h |
| Best for | High head, low flow, light hydrocarbons | General process, medium flow/head |
| Alignment | Factory set – no field alignment | Requires motor-pump alignment |
| Footprint | Very compact | Larger (pump + motor + optional gearbox) |
Verdict: Use OH5 when you need high head at low flow (e.g., 20 m³/h at 350 m) where an OH1/OH2 would require multiple stages or cannot meet the duty. Use OH1/OH2 for standard medium flow/head applications.
OH5 vs BB Type Pumps (BB1, BB2, BB3)
| Feature | OH5 | BB1 / BB2 / BB3 |
|---|---|---|
| Configuration | Overhung with integral gear | Between bearings (multistage or single stage) |
| Flow range | Low to medium (2–800 m³/h) | Medium to large (up to 3,400+ m³/h) |
| Head range | High (single stage high speed) | Medium to very high (multistage) |
| Footprint | Very compact | Larger and heavier |
| Cost | Lower (simpler construction) | Higher (more bearings, larger casing) |
| Best for | High head, low flow, limited space | Large flow, high head, continuous heavy duty |
Verdict: For low flow (e.g., <200 m³/h) and high head (e.g., >200 m), the OH5 is often more cost-effective and compact than a multistage BB3 pump. For larger flows, BB pumps are still the better choice.
Best Suitable Conditions for OH5 Pump
High speed, low flow, high head duty
Limited installation space (offshore, skid, retrofit)
Light hydrocarbon, condensate, LPG, NGL, clean solvents
Applications requiring API 610 compliance but with smaller footprint
Where standard OH1/OH2 cannot achieve enough head at desired flow
Get an OH5 Pump vs OH1/OH2/BB Comparison for Your Duty
Not sure whether OH5, OH1/OH2, or a BB pump is best for your high head low flow application? Our engineering team provides free pump selection advisory.
Send us your duty point:
Flow rate (m³/h or GPM)
Total head (m or ft)
Fluid name and temperature (°C)
Available space or skid requirement
Any special requirement (low NPSH, seal plan, ATEX, etc.)
We will reply within 24 hours with:
Recommended pump type (OH5, OH1/OH2, or BB)
Side-by-side comparison for your specific duty
High-speed performance curve and API data sheet
CAD drawing (2D) and 3D model
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1, OH2, OH3, OH4, OH5, BB1, BB2, BB3, BB4, BB5, VS types) serving global refineries, petrochemical plants, gas plants, and offshore facilities. Contact us for custom-engineered OH5 integral gear drive pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.