Regenerator Base Pump – API 610 OH2 / BB3 / VS4 for Lean Amine & Column Bottoms Transfer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 regenerator base pump for removing lean amine or stripped liquid from the bottom of a regenerator (stripper) column. OH2 single‑stage, BB3 high‑head multistage, VS4 vertical sump. 316L stainless steel (S‑8) wetted parts. API 682 Plan 53B dual pressurized seals for H₂S containment. Handles hot lean amine (100–130°C). Flows 10–1500 m³/h, heads 20–1500 m. 20‑year design life, 3‑year continuous run.

Conatct For Details
DetailReview(0)Additional

Product Overview

The Regenerator Base Pump is a critical pump located at the bottom (base) of a regenerator (stripper) column in gas sweetening, refinery hydrodesulfurization (HDS), carbon capture (CCUS), and solvent regeneration processes. Its primary function is to continuously remove the stripped liquid – typically hot lean amine (MDEA, MEA, DEA that has been regenerated) – from the column base and transfer it either to the reboiler for steam generation or to the lean amine charge pump for circulation back to the absorber. The pump may also handle other regenerator base liquids such as stripped sour water or glycol.

The fluid at the regenerator base is hot (typically 100–130°C), may contain residual H₂S and CO₂, is corrosive, and must be handled safely and reliably to maintain continuous plant operation. All pumps are fully compliant with API 610 11th/12th edition (ISO 13709) standards – ensuring a 20‑year design life and a minimum 3‑year uninterrupted operation. Available in three API 610 configurations – OH2 (single‑stage overhung), BB3 (multistage between bearings), and VS4 (vertical sump) – the Regenerator Base Pump covers all typical column bottom transfer duties.

Pump Configurations for Regenerator Base Service

Pump TypeConfigurationBest Regenerator Base Application
OH2 (Preferred)Overhung, centreline‑mounted, single‑stageStandard lean amine transfer to reboiler or lean charge pump (heads ≤150 m, flows 10–600 m³/h)
BB3Axially split, multistage, between bearingsHigh‑head transfer (>150 m) when the reboiler is elevated or the charge pump requires high suction pressure
VS4Vertical suspended sump / can typeLow NPSHa at column base (e.g., shallow sump or vacuum column); fire‑code or space‑constrained installations

Key Technical Specifications

ParameterOH2BB3VS4
Flow range10 – 600 m³/h50 – 1500 m³/h10 – 750 m³/h
Head range20 – 260 m (typical 50–150 m)100 – 1500 m15 – 280 m
Pressure ratingUp to 64 barUp to 150 barUp to 40 bar
Temperature–45 to +200°C–45 to +200°C–46 to +260°C
Speed1,450 / 2,950 rpm1,450 / 2,950 rpm1,450 / 2,950 rpm

Materials – API 610 Table H

Lean amine at regenerator base temperature (100–130°C) is corrosive, especially in the presence of residual H₂S, CO₂, and heat‑stable salts. 316L stainless steel (API 610 Class S‑8) is the minimum standard. Carbon steel is not acceptable.

ComponentMaterial (Standard)Upgrade Option
Casing316L SS (CF3M)Duplex (D‑1/D‑2), Super Duplex (U‑8)
Impeller316L SSDuplex, Super Duplex, 17‑4 PH
Shaft316 SS or 4140 with coating17‑4 PH, Duplex SS
Wear rings316L SS + Stellite hard‑facingTungsten carbide
Gaskets / O‑ringsSpiral wound (graphite) / FKMAflas for higher temperature

For lean amine with H₂S partial pressure above NACE limits, NACE MR0175 / ISO 15156 certification is required.

Mechanical Seals – API 682 Compliance

Although lean amine has lower H₂S concentration than rich amine, residual H₂S plus high temperature requires robust sealing. Dual pressurized seals (API 682 Arrangement 3) with Plan 53B are strongly recommended. For very low H₂S and well‑ventilated areas, a tandem seal (Plan 52) may be acceptable, but Plan 53B is the industry standard for safety and emissions compliance.

Seal ArrangementAPI 682 PlanApplication
Dual pressurised (Arr. 3)Plan 53BRecommended – zero emissions, barrier fluid pressure > process, ideal for hot lean amine
Tandem seal (Arr. 2)Plan 52Acceptable only for lowest H₂S residual, not preferred
Single seal (Arr. 1)Plan 11 / 23Not recommended for hot amine (Plan 23 cooled may be used for non‑H₂S service)

Plan 53B provides barrier fluid pressurised above process pressure using a bladder accumulator, eliminating any leakage of amine or H₂S. Seal faces: silicon carbide (SiC) / SiC. Elastomers: FKM (Viton) for up to 120°C; Aflas for higher temperatures.

NPSH Considerations

The regenerator base pump typically takes suction from the bottom of a column operating near atmospheric pressure (or slight vacuum in some designs). The liquid level above the pump centreline may be only 2–6 meters, providing limited NPSHa. The fluid is hot and near its bubble point – dissolved gases (CO₂, H₂S, methane) flash easily.

  • Keep suction piping as short and direct as possible, properly insulated.

  • Calculate NPSHa at the bubble point – do not assume subcooling.

  • Select a low‑NPSHr impeller or add an inducer if margin is insufficient.

  • Ensure NPSHa ≥ NPSHr + 1.0 m per API 610.

  • Consider a VS4 vertical pump if NPSHa from horizontal OH2 is inadequate.

Minimum Flow Protection

The regenerator base pump operates continuously while the plant is online. If the downstream valve (to reboiler or charge pump) closes, the pump must be protected. An automatic recirculation valve (ARC) or a continuous bypass line with orifice must return the minimum required flow to the column base.

Applications for Regenerator Base Pump

IndustryProcessFluidPump Configuration
Natural gas sweeteningAmine regenerationLean MDEA / MEA (100–130°C)OH2 (standard)
Refinery HDSAmine strippingLean MDEA / DEAOH2 or BB3
CCUS (carbon capture)MEA regenerationLean MEAOH2
Sour water strippingSour water stripperStripped sour waterOH2 (316L SS or duplex)
Glycol dehydrationGlycol regeneratorLean glycolOH2 (carbon steel or 316L)

API 610 Compliance Highlights

  • Design life: 20 years minimum

  • Continuous operation: Minimum 3 years uninterrupted service

  • Bearing life: L10 ≥25,000 hours

  • Critical speed: ≥120% of maximum operating speed

  • Centreline mounting (OH2/BB3): Essential for hot service (100–130°C)

  • Hydrostatic test: 1.5x design pressure

  • Performance test: Water per API 610 Grade 1 or 2

  • Material certification: EN 10204 3.1 full traceability

  • NACE MR0175 / ISO 15156 available for sour lean amine

Why Choose Our Regenerator Base Pump?

  • Full API 610 compliance (OH2 / BB3 / VS4) – 11th/12th edition ISO 13709, 20‑year life

  • 316L stainless steel (S‑8) as standard – proven corrosion resistance in hot lean amine

  • API 682 Plan 53B dual pressurised seals – zero emissions, safe containment of residual H₂S

  • Broad hydraulic coverage – flows 10–1500 m³/h, heads 20–1500 m

  • Low NPSH designs – inducer option for low‑elevation column bases

  • Centreline mounting – maintains alignment during thermal cycling (up to 200°C)

  • Easy maintenance – back pull‑out (OH2), axial split (BB3), vertical withdrawable (VS4)

  • Minimum flow protection – ARC or bypass integrated

  • NACE MR0175 / ISO 15156 compliant options

  • Field proven – thousands of regenerator base pumps in gas plants and refineries worldwide

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (API 682 Plan 53B ready)1 set
Bearing set (radial + thrust)1 set
Wear ring set (casing + impeller)1 set
Gasket / O‑ring kit (full set)1 set
Inducer (if fitted)1 set

Get a Quote or Engineering Support

For selection of the correct Regenerator Base Pump for your amine or solvent regeneration unit – including column bottom conditions (temperature, pressure, fluid composition, H₂S residual), NPSHa calculation, material selection (316L SS, duplex, or NACE MR0175), API 682 seal plan (Plan 53B), and complete API 610 data sheet – please contact our engineering team.

Email: info@hyrig.com

Our engineers support gas sweetening, refinery HDS, carbon capture, and solvent regeneration projects worldwide with reliable API 610 regenerator base pumps – safe, corrosion‑resistant transfer of hot lean amine from column base to reboiler or charge pump.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit