A slurry pump must withstand severe abrasive and often corrosive duty. Our API 610 OH2 centrifugal pump is engineered specifically for heavy‑duty slurry applications. It fully complies with API 610 11th/12th edition (ISO 13709) – the global standard for refinery and heavy process pumps, but adapted with slurry‑specific materials and wear protection.
Why API 610 OH2 for slurry service?
The OH2 type is a horizontal, single‑stage, overhung impeller pump with foot‑mounted casing. For slurry applications, this design offers:
Easy maintenance – Back pull‑out design allows rotor, bearing housing and seal removal without disturbing piping or motor.
Heavy duty bearing housing – Large oil bath or oil mist bearings designed for high radial loads from dense slurries.
API 682 seal compatibility – Fits cartridge mechanical seals, or optional expeller / dynamic seal for reduced abrasive wear.
Replaceable wear parts – Hard metal or elastomer liners, replaceable impeller and throatbush.
Robust shaft & bearing – Oversized shaft diameter reduces deflection, extending seal and bearing life.
Key design features for slurry duty
Wetted materials – High chrome white iron (Cr27, Cr15Mo3), Ni‑Hard, natural rubber, polyurethane, or duplex stainless steel depending on slurry chemistry and abrasiveness.
Thick section casing – Extra metal thickness for wear allowance.
Replaceable wear liners – Front and rear liners protect casing from direct slurry impact.
Oversized shaft – Minimum deflection at seal area.
Heavy duty taper roller bearings – Designed for high radial and axial thrust from dense slurries.
Sealing options –
Gland packing with flush water (low cost, tolerant of abrasives)
Expeller / dynamic seal (no flush water, reduces wear)
API 682 cartridge mechanical seal (for toxic or corrosive slurries)
Efficiency – Optimized impeller vane profile reduces recirculation and wear, maintaining efficiency over longer periods.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 10 – 3000 m³/h |
| Head | 10 – 120 m (higher on request) |
| Max particle size | Up to 100 mm (depending on impeller passage) |
| Temperature | Up to 120°C (special design up to 250°C) |
| Pressure rating | Up to 25 bar |
| Speeds | 750 – 1500 rpm (direct or VSD) |
Typical applications
Mining – Tailings, concentrates, mill discharge, cyclone feed, thickener underflow.
Mineral processing – Ore slurry, sand, gravel, coal washing, phosphate.
Dredging – Sand and gravel extraction.
Industrial – Power plant ash handling, steel mill scale slurry, cement slurry.
Chemical – Crystalline slurries, catalyst slurry, abrasive chemical mixtures.
Why choose our API 610 OH2 slurry pump?
Proven heavy duty design – Based on API 610 OH2 standards but optimized for abrasive service.
Longer wear life – High chrome or elastomer liners with hardness >600 HB.
Easy parts replacement – Modular construction with interchangeable wet end components.
Lower total cost – Competitive initial price, longer MTBR, and globally available spare parts.
Short lead time – Standard sizes ex‑stock; custom materials available in 4–6 weeks.
Global support – Impellers, liners, shafts, bearing housings, seals shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
Hydraulic performance test, vibration & bearing temperature monitoring.
Hardness testing for high chrome parts.
Material certificates EN 10204 3.1 (3.2 optional).
Hydrostatic test of casing.
How to specify your slurry pump
Please provide: flow (m³/h), head (m), specific gravity of slurry, particle size / shape / concentration (% solids by weight), pH, temperature, and NPSHa. Also indicate if the slurry is abrasive, corrosive, or both. We will recommend material type (high chrome, rubber, or alloy), sealing arrangement, and drive options.
Contact us
For a quotation or technical discussion on slurry pumps (API 610 OH2):
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.