The VS1 pump is an API 610 fully vertical submerged multistage pump, installed entirely inside a tank, sump, or vessel. It is the best choice for low NPSH and high head process conditions where horizontal pumps would cavitate or require excessive suction head. Below we compare the VS1 against OH3/OH4 vertical sump pumps, horizontal BB/OH pumps, and other VS types to help you select the right vertical submerged pump for your tank application.
Core Advantages of VS1 Pump
Fully Submerged Installation → Extremely Low NPSH, Anti-Cavitation
The entire pump sits below the minimum liquid level. The static head of the liquid column provides positive suction pressure. Even for boiling point liquids (condensate, light hydrocarbons, hot water), cavitation is eliminated. External suction piping is not required.
Multistage Design → Realize Ultra High Head in Limited Space
Multiple stages (2–10+) generate heads up to 1,200 meters (3,940 ft) without requiring large diameter impellers or high-speed operation. The vertical configuration packs high head capability into a compact footprint.
Vertical Tank Internal Layout → Save Outdoor Floor Area
No baseplate, no foundation, no motor platform. The pump hangs from the tank nozzle. Valuable ground space is saved – critical for congested refineries and petrochemical plants.
Liquid Lubricated Bearings → Simple Structure, Low Noise
Internal bearings are lubricated by the pumped liquid itself. No oil, no grease, no external lubrication system. Maintenance is minimal, and noise levels are low.
No Complex Civil Foundation, Easy Installation and Maintenance
The pump installs through a tank top nozzle. No concrete foundation, no baseplate alignment, no suction piping. The entire rotating assembly can be pulled out from above for maintenance.
VS1 vs OH3 / OH4 (Vertical Sump Pumps)
| Feature | VS1 (Submerged Multistage) | OH3 / OH4 (Cantilever Sump) |
|---|---|---|
| Installation | Fully submerged inside tank | Mounted on pit edge / tank top, below liquid |
| Head capability | High (multistage, up to 1,200 m) | Medium (single stage, up to 160 m) |
| NPSH performance | Extremely low (submerged) | Good (cantilever) |
| Best for | High head, low NPSH tank internal | Sump drainage, medium head |
| Space usage | Inside tank – saves floor space | Above ground – requires access |
Verdict: Use VS1 when you need high head from a low liquid level or extremely low NPSH. Use OH3/OH4 for general sump pumping with medium head requirements.
VS1 vs Horizontal BB / OH Pumps (BB1, BB2, OH1, OH2)
| Feature | VS1 | Horizontal (BB/OH) |
|---|---|---|
| NPSH requirement | Extremely low (submerged) | Higher (requires positive suction head) |
| Suction piping | None (draws directly from tank) | Required – potential leak points |
| Floor space | Minimal (inside tank) | Large (baseplate + motor) |
| Foundation | No complex foundation | Requires concrete foundation |
| Low liquid level | Excellent | Poor (may cause cavitation) |
| Head range | High (multistage) | Low to medium (single stage) |
Verdict: Choose VS1 when NPSH is limited, liquid level is low, or heavy hydrocarbons/condensate are involved. Choose horizontal pumps for above-grade installation with sufficient NPSH.
VS1 vs Other VS Types (VS2, VS3, VS4, VS5, VS6, VS7)
VS1: Fully submerged multistage – standard tank internal high head type. Entire pump below liquid. Most common for low NPSH high head.
VS2: Vertical submerged with discharge column – similar to VS1 but with longer column.
VS3: Vertical wet pit pump with suction strainer – for large flows, lower heads.
VS4: Vertical submerged with oil-lubricated bearings – for high temperature or dirty liquids.
VS5: Vertical submerged with external discharge head – special configurations.
VS6: Vertical in-line pump – dry installed, not submerged.
VS7: Vertical axial flow propeller pump – high flow, low head.
VS1 is the standard choice for:
Low NPSH, high head tank internal pumping
Condensate, light hydrocarbons, hot water
Refinery, petrochemical, power plant tank services
Any application requiring a fully submerged multistage pump
Get a VS1 Pump vs OH3/OH4 / Horizontal / vs Other VS Comparison for Your Duty
Our engineering team provides free pump selection advisory. Send us your duty point:
Flow rate (m³/h or GPM)
Total head (m or ft)
Fluid name and temperature (°C)
Tank/sump depth and liquid level
Any special requirement (low NPSH, corrosive, high temp)
We will reply within 24 hours with:
Recommended pump type (VS1, VS2, OH3, OH4, or horizontal)
Side-by-side comparison for your specific duty
Performance curve and API data sheet
Tank installation drawing (2D CAD)
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1–OH6, BB1–BB5, VS1–VS7 types) serving global refineries, petrochemical plants, power utilities, chemical facilities, and condensate systems. Contact us for custom-engineered VS1 fully submerged multistage pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.