The VS5 pump is an API 610 vertical multistage long shaft pump, specifically designed for deep sump and high head applications where ordinary sump pumps (single stage or fully submerged) cannot reach the required depth and lift. With its top‑mounted dry motor, custom long column, and multistage impellers, the VS5 provides a reliable, easy‑to‑maintain solution for deep pits, high head drainage, and critical process pumping in refineries, petrochemical plants, power stations, and mines. Below we compare the VS5 against VS1/VS2 and VS3/VS4 vertical pumps.
Core Advantages of VS5 Pump
Top Motor Design → No Submerged Motor, Low Failure & Easy Maintenance
Motor sits on a top deck above the sump, completely dry. No sealed motor required, no risk of flooding or electrical failure. Motor is easily accessible for inspection, lubrication, or replacement – without pulling the pump.
Custom Long Column → Adapt to Deep Sump / Deep Pit Installation
Column length is customized to your sump or pit depth (1 m to 6 m or longer). The pump bowl assembly sits at the bottom of the column, fully submerged. Reaches where short‑stem sump pumps cannot.
Multistage Impeller → Provide Much Higher Head than Single Stage VS3/VS4
Two to ten stages generate heads up to 1,000 meters. Single‑stage VS3 or VS4 pumps are limited to 150 m head. For deep vertical lift or high system pressure, the VS5 is the correct choice.
Stable Line Shaft Bearing System → Low Vibration, Long‑Term Operation
Intermediate bush bearings along the column support the long line shaft. Lubricated by the pumped liquid, these bearings provide stable alignment, minimal vibration, and years of continuous service.
Wide Medium Adaptability – Available in cast iron, carbon steel, 316L, duplex, and high‑chrome alloys for water, oil, and mildly corrosive liquids.
VS5 vs VS1 / VS2 (Can‑Type or Fully Submerged Multistage Pumps)
| Feature | VS5 | VS1 / VS2 |
|---|---|---|
| Motor location | Top deck (dry, accessible) | Top deck (dry for VS1; VS2 can type external) |
| Column / can | Long shaft column (open to sump) | Can casing (enclosed) for VS2 |
| Submerged components | Impeller bowl + line shaft bearings | Entire pump bowl inside can or submerged |
| Maintenance | Pull line shaft + bowl from top | Pull cartridge (VS1) or can internal (VS2) |
| Best for | Deep open sumps, pits, tanks | Low NPSH can‑type feed (VS2), fully submerged (VS1) |
Verdict: Use VS5 for deep open sumps/pits where easier maintenance is desired. Use VS1/VS2 when a flooded can or fully submerged installation is required for very low NPSH.
VS5 vs VS3 / VS4 (Single‑Stage Vertical Pumps)
| Feature | VS5 | VS3 / VS4 |
|---|---|---|
| Stage type | Multistage (2–10 stages) | Single stage |
| Head range | High to very high (40–1,000 m) | Low to medium (3–150 m) |
| Flow range | Small to medium (5–1,500 m³/h) | Medium to ultra‑large (VS3: 200–8,000; VS4: 500–20,000+) |
| Column depth | Deep sump capable (1–6 m+) | Shorter column (VS3/4 typically pit mounted) |
| Best for | High head, deep sump, low flow | Large flow, low head, shallow sump |
Verdict: Choose VS5 when you need high head (>150 m) from a deep sump and flow is moderate. Choose VS3 for large flow, medium head (>15 m); choose VS4 for ultra‑large flow, very low head (<30 m) applications.
Best Application for VS5 Pump
Deep pit, deep sump requiring high head
Refinery oily water recovery from API separator pits (20–60 m deep)
Power plant condensate lifting from hotwells (high head, low NPSH)
Mine dewatering from deep shafts
Any installation where a submerged motor is not allowed (hazardous area, high temperature, risk of flooding)
Get a VS5 Pump vs VS1/VS2/VS3/VS4 Comparison for Your Duty
Our engineering team provides free pump selection advisory. Send us your duty point:
Flow rate (m³/h or GPM)
Total head (m or ft)
Fluid name and temperature (°C)
Sump depth (mm or inches)
Any special requirement (submerged motor prohibited, low NPSH, corrosive, etc.)
We will reply within 24 hours with:
Recommended pump type (VS5, VS1/VS2, or VS3/VS4)
Side‑by‑side comparison for your specific duty
Performance curve and API 610 data sheet
Long column installation drawing (2D CAD)
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1–OH6, BB1–BB5, VS1–VS7 types) serving global refineries, petrochemical plants, power utilities, chemical facilities, mining operations, and general industry. Contact us for custom‑engineered VS5 vertical multistage long shaft sump pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.