VS5 Pump Technical Specifications – API 610 Vertical Multistage Long Shaft Sump Pump for Deep Sump High Head Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
VS5 pump API 610 vertical multistage long shaft sump pump technical specifications. Performance: flow 5–1500 m³/h, head 40–1000 m, speed 1480/2980 rpm, temperature -20°C to 200°C, max pressure 100 bar, custom sump depth 1–6 m. Structure: vertical multistage long shaft (VS5), top mounted dry motor (not submerged), long vertical discharge column (custom length), 2–10 stages, high strength alloy line shaft, water/liquid lubricated intermediate bush bearings, sump pit/tank top installation. Materials: cast iron/carbon steel/316L/duplex casing & column; stainless steel/high chrome impeller; alloy steel/316L shaft; anti-corrosion wear bushings. Documents: API data sheet, long column installation drawing, performance curve, 3D model, material certificate.

Conatct For Details
DetailReview(0)Additional

This page provides complete technical parameters for our VS5 API 610 vertical multistage long shaft sump pump. The VS5 is designed for installation over a deep sump, pit, or tank, with the motor mounted on a top deck – completely above the liquid. No submerged motor. The long vertical column and multistage impellers deliver high head (up to 1,000 m) from deep sump levels, making it ideal for refinery oily water recovery, power plant condensate lifting, chemical tank transfer, and mine dewatering.


Performance Range

ParameterValue
Flow rate5 ~ 1,500 m³/h (22 ~ 6,600 GPM)
Total head40 ~ 1,000 m (131 ~ 3,280 ft) – higher on request
Speed1,480 / 2,980 rpm (50/60 Hz)
Medium temperature-20°C ~ +200°C (-4°F ~ +392°F) – higher with special materials
Maximum working pressureUp to 100 bar (1,450 psi)
Sump depthCustom – 1 m ~ 6 m (3.3 ft ~ 20 ft) – longer on request

Structural & Mechanical Design

  • Type: Vertical multistage long shaft sump pump (API 610 VS5 designation)

  • Motor: Top mounted, dry type, not submerged – motor on grade level or deck, safe from flooding and vapor

  • Column: Long vertical discharge column, customizable length – matches your sump or pit depth

  • Stages: 2–10 stages multistage design – add stages to increase head

  • Shaft: High strength alloy line shaft – transmits torque from top motor to submerged impellers

  • Bearings: Water/liquid lubricated intermediate bush bearings – located along the column; no external lubricant required

  • Installation: Sump pit / tank top mounted – pump hangs from top mounting plate; simple civil work


Material Options

ComponentStandard MaterialsUpgrade Options
Casing & columnCast iron, carbon steel316L, duplex, super duplex
Impeller & diffuserStainless steel (304/316L), high chrome alloyDuplex, 17-4PH, bronze
Line shaftAlloy steel (4140)316L, duplex
Wear bushingsAnti-corrosion wear-resistant alloyColmonoy-coated, Stellite

Key Design Features Explained

Top Motor – No Submerged Motor
Unlike some submersible pumps, the VS5 motor sits above the sump, at grade or on a deck. No sealed motor required; no risk of electrical failure due to flooding. Motor is easily accessible for inspection and maintenance.

Long Column for Deep Sump
The vertical column can be customized from 1 to 6 meters or longer. The pump bowl assembly sits at the bottom of the column, submerged in the liquid. The line shaft runs inside the column to drive the impellers.

Multistage for High Head
Two to ten stages allow the VS5 to achieve heads up to 1,000 meters without requiring high-speed motors or large-diameter impellers. Each stage adds pressure incrementally.

Liquid Lubricated Line Shaft Bearings
Intermediate bush bearings are located along the column to support the long shaft. These bearings are lubricated by the pumped liquid – no oil, no grease, no external lubrication system.

Low NPSH Performance
The submerged first stage impeller is below the minimum liquid level, providing positive suction head. Low NPSH requirement – suitable for condensate, hot water, and light hydrocarbons.


Typical Applications

  • Deep pit drainage (refinery, chemical plant)

  • Sump high-head pumping (oily water, process waste)

  • Refinery oily water recovery from API separator sumps

  • Power plant condensate lifting from hotwells

  • Chemical tank medium transfer (deep tanks)

  • Mine deep water pumping


Available Technical Documents (Free Request)

  • API 610 data sheet (filled with your operating conditions)

  • Long column installation drawing (2D CAD, PDF/DWG) – includes column length, mounting flange, sump pit details

  • Performance curve (head, efficiency, NPSHr vs flow)

  • 3D model (STEP/IGES for plant layout)

  • Material certificate (EN 10204 3.1 or 3.2)

  • Hydrostatic and performance test report


Get Your VS5 Pump Technical Specification Package

To request a complete documentation package with a formal quotation, please send us your operating conditions:

  • Flow rate (m³/h or GPM)

  • Total head (m or ft)

  • Fluid name and temperature (°C)

  • Sump depth (mm or inches) – for column length

  • Any special requirement (number of stages, material, low NPSH, ATEX, etc.)

Our engineering team will respond within 24 hours with:

  • Recommended VS5 pump model (stages, column length, material)

  • Performance curve PDF

  • API 610 data sheet

  • Long column installation drawing (2D CAD) and 3D model link

  • Bearing and material recommendations

  • Factory direct price (EXW / FOB / CIF)

Email: info@hyrig.com

We are a professional API 610 pump manufacturer (OH1–OH6, BB1–BB5, VS1–VS7 types) serving global refineries, petrochemical plants, power utilities, chemical facilities, and mining operations. Contact us for custom-engineered VS5 vertical multistage long shaft sump pumps at factory direct wholesale pricing.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit