The XQ140/12A hydraulic power tong is a heavy‑duty, open‑throat workover tool designed for make‑up and break‑out of tubing, small drill pipe, and casing from 2⅜" to 5½" (Φ60–140 mm). To ensure continuous, trouble‑free operation, stocking the correct genuine wear parts is essential. This guide provides a complete recommended spare parts list for one XQ140/12A unit, including core mechanical wear parts and a full O‑ring seal kit.
| No. | Part No. | Part Name | Application / Location | Recommended Qty |
|---|---|---|---|---|
| 1 | 12AZ-32 | Brake spring | Brake mechanism | 12 |
| 2 | 12AZ-54 | Friction plate | Brake mechanism | 4 |
| 3 | 12AZ-58/59/70 | Reset knob assembly (complete) | Master tong reset | 1 set |
| 4 | 12AZ-61/63 | Centering roller assembly | Jaw centering | 20 sets |
| 5 | 12AZ-114 | Jaw roller | Jaw carrier drive | 4 |
| 6 | 12AZ-109 | Bolt stop pin | Die holder fixing | 16 |
| 7 | 12AZ-119 | Roller | Transmission mechanism | 18 |
| 8 | 12AZ-101 | Stop pin | Limiting | 1 |
| 9 | 12AZ-110.1 | Jaw plate – size 1 | Tubing gripping | 20 |
| 10 | 12AZ-110.2 | Jaw plate – size 2 | Tubing gripping | 20 |
| 11 | 12AZ-110.3 | Jaw plate – size 3 | Tubing gripping | 20 |
| 12 | 12AB-3/12/13 | Backup reset knob assembly | Backup tong reset | 1 set |
| 13 | 12AB-4 | Stop pin | Backup tong limiting | 1 |
| 14 | 12AB-43 | Rack plunger | Backup tong gripping | 1 |
| Seal Size (mm) | Part No. | Application Location | Recommended Qty |
|---|---|---|---|
| 16×2.4 | 12AZ-245 | Master tong lift valve needle | 1 |
| 18×2.4 | 12AB-53 | Backup high‑pressure hose ball end | 7 |
| 22×2.4 | 12AB-265 | Manual control valve, hose fitting | 9 |
| 24×2.4 | 12AY-1.6 | Hydraulic lift cylinder fitting | 1 |
| 25×2.4 | 12AZ-247 | Torque gauge port, lift valve spool | 2 |
| 26×2.4 | 12AZ-216 | Master tail fitting, hollow bolt | 3 |
| 28×3.1 | 12AZ-234 | Interface between lift valve and hand valve | 3 |
| 30×3.1 | 12AZ-235 | Lift valve | 1 |
| 32×3.5 | 12AY-1.14 | Master hydraulic motor port | 4 |
| 36×3.5 | 12AZ-201 | Master manual control valve | 2 |
| 44×3.5 | 12AB-69 | Replenishing / sensor cylinder | 7 |
| 45×3.5 | 12AY-1.16 | Hydraulic lift cylinder piston | 2 |
| 50×3.5 | 12AZ-124 | Master waterproof cover | 2 |
| 50×3.55 | 12AB-105 | Backup rack plunger cylinder cover | 2 |
| A40×1.5 | 12AB-102 | Backup rack plunger | 2 |
Jaw plates (12AZ-110.1 / .2 / .3) and die holders – Always replace in matched pairs. Select the correct size for the tubing diameter (size 1, 2, or 3 corresponds to the 2⅜"–5½" range).
Brake springs (12AZ-32) and friction plates (12AZ-54) – High‑frequency wear items. Worn springs or plates cause slipping and reduced braking torque. Inspect regularly and replace as needed.
Seals (O‑rings) – Aging seals lead to hydraulic oil leaks. It is recommended to inspect and replace after each well job or at least monthly.
Pre‑assembled kits – For the reset knob assemblies (master and backup) and centering roller assemblies, order the complete assembly (总成) for faster installation – no need to assemble individual components in the field.
Important – Always use genuine Yancheng TEDA original parts. Non‑genuine parts may cause premature failure, unsafe operation, and will void warranty.
For genuine XQ140/12A wear parts, seal kits, or complete spare parts packages, please contact:
info@hyrig.com
*We offer fast response, original factory packaging, and technical support for all XQ series power tongs (XQ89/3C, XQ114/9, XQ140/12A, and others).*
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.