The XQ89/3C hydraulic power tong is an advanced workover tool manufactured by Yancheng TEDA Drilling and Production Equipment Co., Ltd. It is specifically designed for make-up (running in) and break-out (pulling out) of tubing connections in oil and gas well servicing. This guide provides full instructions from pre-installation to post-operation maintenance.
Multi-size tubing without parts change – Fits 2⅜", 2⅞" and 3½" tubing using an internal cam‑roller gripping mechanism.
Two-speed operation – High gear: up to 100 r/min for rapid spinning; Low gear: 3.0 kN·m rated torque (at 10 MPa) and 4.0 kN·m max torque (at 12.5 MPa) for heavy-duty make-up.
Synchronized master & hydraulic backup tong – Controlled by a single manual directional valve for simultaneous clamping and releasing.
Top-mounted brake mechanism – Easy adjustment and maintenance on the master tong cover.
Precise torque control – Adjust system pressure (rated 10 MPa, max 12.5 MPa) to achieve optimal torque for different tubing grades.
| Parameter | Master Tong | Backup Tong |
|---|---|---|
| Tubing / coupling range | 2⅜", 2⅞", 3½" | 2⅜" – 3½" upset couplings |
| Jaw opening | 95 mm | 116 mm |
| High gear speed (@80 L/min) | 100 r/min | – |
| Low gear speed (@80 L/min) | 30 r/min | – |
| High gear rated torque (@10 MPa) | 1.1 kN·m | – |
| Low gear rated torque (@10 MPa) | 3.0 kN·m | – |
| Low gear max torque (@12.5 MPa) | 4.0 kN·m | – |
| Rated system pressure | 10 MPa | – |
| Max system pressure | 12.5 MPa | – |
| Rated oil flow | 80 L/min | – |
| Weight | 122 kg | 58 kg |
| Combined dimensions | 715×430×550 mm | – |
Suspension – Hang the power tong from the workover rig mast using the master tong hanger rod assembly (3C1-45(1)). The suspension point must be at least 15 m above ground. Keep the tong freely suspended. Adjust height so the backup tong faces the tubing coupling, with the tong center about 0.5 m from the well center (see Fig. 1).
Leveling – Turn the adjustment screw (3C1-89(1)) on the hanger bracket until both master and backup tongs are perfectly horizontal. Tilting can cause gripping failure and safety hazards.
Tail rope – Secure one end of the tail rope to the rig mast and the other end to the rear guide rod base (3C1-34A). The rope must have a minimum breaking strength of 20 kN. When the tong is in the make-up position, the tail rope must be perpendicular to the tong to protect the operator (see Fig. 2).
Hydraulic connections – Connect the pressure hose from the hydraulic power unit to the upper port of the manual directional valve, and the return hose to the lower port. Ensure tight, leak‑free connections. Verify circuit integrity using the hydraulic diagram (Fig. 3).
Wear full PPE: coverall, safety shoes, hard hat, protective gloves.
Check that the single‑leaf safety door (3C1-147) closes freely and latches securely. The safety door must be closed during operation.
Remove any debris from the operating area. Check all bolts (hex head, socket head screws) for tightness.
Ensure hydraulic oil is clean and at proper level. Oil temperature must not exceed 65°C. Clean the filter regularly.
High gear (fast speed) – Push down the shift fork shaft (3C1-135) while operating the manual directional valve.
Low gear (high torque) – Pull up the shift fork shaft.
Important – Shift gears only when the tong is running at low speed or completely stopped. Never shift at high speed – gear damage will result.
Align the master and backup tong jaw openings so the tubing can enter.
Turn the reset knobs (3C1-54 on master, 3C2-2 on backup) so the arrow points to "make-up" direction.
Move the tong onto the tubing string until the tubing is fully seated in the gripping area.
Operate the manual directional valve to rotate the master tong in the make-up direction.
Tighten the connection to the required torque. Monitor the system pressure on the pressure gauge (4). Use the pressure‑torque correlation chart (Fig. 4) to verify torque:
High gear: 1.1 kN·m @10 MPa
Low gear rated: 3.0 kN·m @10 MPa
Low gear max: 4.0 kN·m @12.5 MPa
After make-up is complete, reverse the valve to rotate the tong backward until the jaws align with the opening. Pull the tong away from the tubing.
Align the master and backup jaw openings.
Turn the reset knobs (3C1-54, 3C2-2) so the arrow points to "break-out" direction.
Position the tong onto the tubing coupling.
Operate the manual directional valve to rotate the master tong in the break-out direction until the thread connection is fully loosened.
Reverse the valve to align the jaws, then remove the tong from the tubing.
Removal – Use a screwdriver to push the jaw retaining pin (master: 3C1-109, backup: 3C2-44) inward, then remove the old jaw.
Selection & installation – Choose the correct jaw according to tubing size (see table below). Insert the new jaw into the jaw carrier, push the retaining pin until it locks. Ensure the jaw is firmly seated.
| Equipment | Tubing OD (mm) | Jaw mark | Part No. | Drawing No. |
|---|---|---|---|---|
| Master tong | Φ60 | 3C R44 | 3C2-29(1) | XYQ3C.B-17(1) |
| Master tong | Φ73-89 | 3C R40 | 3C1-102 | XYQ3C.Z.1-9 |
| Backup tong | Φ60 | 3C R30 | 3C2-29(3) | XYQ3C.B-17(3) |
| Backup tong | Φ73-78 | 3C R36.5 | 3C2-29(2) | XYQ3C.B-17(2) |
| Backup tong | Φ89-93 | 3C R44 | 3C2-29(1) | XYQ3C.B-17(1) |
| Backup tong | Φ108-114 | 3C R40 | 3C1-102 | XYQ3C.Z.1-9 |
After each job, clean off mud, water, oil and drilling fluid residue from the tong body.
Apply grease to all rotating pins, jaw carriers, open gear, and other moving parts. Never use steam to clean the tong – steam will wash out lubricants and cause water ingress.
Shut down the hydraulic power unit. Disconnect hoses (seal the ports if storing long‑term) to prevent debris entry.
Do not exceed max system pressure (12.5 MPa) or max torque (4.0 kN·m) – this damages the tong and may deform tubing.
Never touch rotating parts (open gear, jaw rollers, etc.) while the tong is running.
Do not modify the tong or add/remove parts without authorization. Always use genuine TEDA replacement parts.
Do not start rotation before gear shifting is fully engaged.
Do not stand in front of the jaw opening or along the tubing axis during make-up/break-out.
If hydraulic leak, abnormal noise, or jaw slipping occurs – stop immediately and disconnect hydraulic power.
If the tong becomes unstable or loses grip – secure the tubing first, then check tail rope, suspension components and leveling. Only resume after the fault is corrected.
For unsolvable problems, refer to the “Troubleshooting” section of the manual or contact the manufacturer’s after‑sales service. Never disassemble the tong blindly.
For inquiries, technical support, or to order genuine parts, please contact:
info@hyrig.com
We provide professional after‑sales service and fast on‑site support.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.