XQ89/3C Hydraulic Power Tong – Genuine Wear Parts & Replacement Guide

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The XQ89/3C hydraulic power tong is a workover tool for make-up and break-out of 2⅜"–3½" tubing. This guide lists all genuine wear parts: master/backup jaw dies (for Φ60–Φ114mm), brake friction plate and springs, return springs, O-rings (36×3.5, 26×2.4), copper washer, cylinder seals, shift fork and springs, bearings (6005, 6205-Z), guide rollers, and hydraulic oil filter. Includes replacement procedures, validation steps, and maintenance tips to extend service life.

Conatct For Details
DetailReview(0)Additional

The XQ89/3C hydraulic power tong is designed for reliable tubing make-up and break-out in oil well workover operations. To maintain peak performance and minimize downtime, regular inspection and timely replacement of wear parts are essential. This guide provides a complete list of genuine TEDA wear parts, step‑by‑step replacement procedures, and proven maintenance tips.


1. Complete Wear Parts List by Category

1.1 Gripping & Braking Parts (High‑frequency replacement – directly affects safety)

Part NameLocationSpecification / MarkingOEM Part No.Drawing No.Related Fault
Master jaw dieMaster tong headFor Φ60 tubing (mark 3C R44)3C2-29(1)XYQ3C.B-17(1)Jaw slipping, poor grip
Master jaw dieMaster tong headFor Φ73-89 tubing (mark 3C R40)3C1-102XYQ3C.Z.1-9Worn teeth (>1mm), slipping
Backup jaw dieBackup tong headFor Φ60 tubing (mark 3C R30)3C2-29(3)XYQ3C.B-17(3)Backup slips, cannot assist grip
Backup jaw dieBackup tong headFor Φ73-78 tubing (mark 3C R36.5)3C2-29(2)XYQ3C.B-17(2)Backup slips, uneven grip
Backup jaw dieBackup tong headFor Φ89-93 tubing (mark 3C R44)3C2-29(1)XYQ3C.B-17(1)Backup slips, tooth breakage
Backup jaw dieBackup tong headFor Φ108-114 tubing (mark 3C R40)3C1-102XYQ3C.Z.1-9Backup slips, tubing rotation offset
Brake friction plateBrake & reset mechanismFor brake disc (3C1-53)3C1-50XYQ3C.Z-29Insufficient braking torque, tong self‑rotation
Brake springBrake & reset mechanismSpring force ≥20 kN3C1-33XYQ3C.Z-21Brake failure, gear disengagement
Return springJaw open/close mechanismFits jaw carrier3C1-108XYQ3C.Z.1-14Jaw openings cannot align, jamming

1.2 Sealing Parts (Prevent leaks – maintain system pressure)

Part NameLocationSpecificationOEM Part No.Drawing No.Related Fault
O‑ringMain control valve36×3.5 (oil/ pressure resistant)3C1-113GB1235-76Valve body leak, pressure loss
O‑ringHydraulic fitting26×2.4 (oil/ pressure resistant)3C1-155GB1235-76Fitting leak, oil waste
Copper washerPressure gauge portFor 0‑16 MPa gauge3C1-143XYQ3C.Z.5-18Fluctuating pressure reading, port leak
Seal washerCylinder end coverFor backup cylinder (3C2-19A)3C2-53XYQ3C.B-21Cylinder leak, weak backup action
Dust sealJaw shaft bushingFor roller shaft (3C1-106)3C1-107XYQ3C.Z.1-13Foreign material ingress, shaft rust

1.3 Transmission Parts (Ensure power delivery – prevent jamming)

Part NameLocationSpecificationOEM Part No.Drawing No.Related Fault
Shift forkShift mechanismFits duplex gear3C1-129XYQ3C.Z.6-2Difficult shifting, easy disengagement
Shift springShift mechanismPreload ≥5 kN3C1-133XYQ3C.Z.6-5Unstable gear lock, self‑disengagement
Deep groove ball bearingTransmission6005 (double sealed)3C1-14GB/T276Rotation noise, power loss
Rolling bearingCentering mechanism6205-Z (with dust cover)3C1-28GB/T276Jaw wobble, centering failure
Guide rollerJaw mechanismFits jaw carrier3C1-105AXYQ3C.Z.1-12AJaw jamming, uneven opening/closing

1.4 Filtration & Lubrication Parts (Keep hydraulic system clean – reduce wear)

Part NameLocationSpecificationOEM Part No.Drawing No.Related Fault
Hydraulic oil filter elementHydraulic tankFiltration ≥10 μm3C1-181XYQ3C.Y-1Oil contamination, valve spool sticking
Grease nippleMoving partsM8×1 (straight)3C1-18GB/T1152Difficult greasing, component wear

2. Replacement Procedures for Key Wear Parts

2.1 Before Replacement – Safety & Preparation

  • Safety – Disconnect hydraulic power, shut down the unit, wait for the tong to stop completely. Relieve residual pressure to prevent oil spray.

  • Tools – Hex keys (M6–M12), jaw removal tool, bearing puller, diesel/kerosene, brushes, rags.

  • Parts inspection – Confirm new parts are genuine TEDA, check model and dimensions match the old ones, inspect for cracks or deformation.

2.2 Step‑by‑Step Replacement

(1) Jaw Dies (Most frequent)

  1. Use a screwdriver to push the jaw retaining pin (3C1-109 for master / 3C2-44 for backup) and remove the old jaw.

  2. Clean the jaw groove with diesel to remove drilling fluid, rust, and debris (prevents rapid wear of new jaw).

  3. Insert the new jaw into the slot until fully seated, then push the retaining pin to lock.

  4. Manually rotate the jaw to check for smooth opening/closing – no sticking or looseness.

(2) Seals (O‑rings, washers)

  1. Remove the cover or fitting at the leak location using appropriate tools. Take out the aged/damaged seal.

  2. Clean the seal groove thoroughly – remove oil, dirt, and burrs.

  3. Apply a thin layer of hydraulic oil to the new seal, then install it in the correct orientation (avoid twisting).

  4. Tighten the cover or fitting to the specified torque using a torque wrench – do not overtighten.

(3) Bearings

  1. Remove associated components (gearbox cover, jaw housing) to expose the bearing.

  2. Use a bearing puller to extract the old bearing smoothly – never hammer directly.

  3. Clean the bearing housing, apply high‑temperature grease.

  4. Press the new bearing into place using an arbor press or suitable tool – ensure the bearing face seats fully.

  5. Reinstall associated components and check for smooth rotation with no binding.

2.3 Post‑Replacement Validation

  • No‑load run – Start the tong and run for 5–10 minutes. Check for leaks, abnormal noise, or vibration.

  • Load test – Perform a make‑up / break‑out test under simulated working conditions. Verify firm grip, smooth shifting, and stable pressure.

  • Record – Log the part name, model, replacement date, and operating hours in the fault log for traceability.


3. Maintenance Tips to Extend Wear Part Life

3.1 Daily / After‑Each‑Job Maintenance

  • After each job, clean jaw surfaces and grooves with diesel to prevent debris buildup (reduces slipping).

  • Weekly – Inspect seals for leaks or aging. Replace immediately if damaged to avoid oil waste and component rust.

  • Monthly – Grease transmission parts, especially bearings, roller shafts, and rotating elements (use high‑temperature grease).

  • Quarterly – Clean the hydraulic oil filter and check the element condition. Replace if contaminated.

  • Avoid over‑pressure operation (never exceed 12.5 MPa) – this reduces stress on all wear parts.

3.2 Life Extension Techniques

  • Jaw dies – Always use the correct jaw size for the tubing diameter. Mismatched jaws cause abnormal wear (e.g., large jaw on small tubing).

  • Seal protection – Never use sharp tools near sealing surfaces. Lubricate seals with hydraulic oil during installation to prevent cuts.

  • Hydraulic oil – Use ISO VG 46 anti‑wear hydraulic oil. Keep oil temperature below 65°C. Change oil every 500 hours.

  • Long‑term storage – Before storing the tong for extended periods, replace all aged wear parts, apply rust preventive oil, and store in a dry, ventilated area. This prevents seal hardening and metal corrosion.


For genuine TEDA wear parts, technical support, or to place an order, please contact:

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit