Airflex & WPT Clutch Replacement Guide | How to Verify Fit

2026-11-09 21:45

Key Facts

AttributeValue
PurposeReplacement verification guide
Applies ToAirflex WCB brakes, WPT Power Grip clutches, Eaton PDC disc clutches
Key ChecksNameplate, shaft bore, adapter pattern, plate count

Step 1: Identify the Product Family

Before ordering, confirm exactly what type of unit you have. The three main families use different friction components and are not interchangeable:

  • Water-cooled brakes (WCB): Used for continuous slip braking. Look for water ports.
  • Drum clutches (WPT Power Grip): Used for in-line power transmission. Look for an air tube and driving ring.
  • Disc clutches (PDC): Used for high-speed, low-inertia engagement. Look for a flat disc pack.

Step 2: Read the Nameplate

Confirm the exact model code on the nameplate. Examples include `236WCB`, `WPT 318`, `118PDC`, and `SHD324`. If the nameplate is unreadable, take a photo and send it to HYRIG engineers for identification.

Step 3: Measure the Shaft and Adapter

For clutches (WPT and PDC), measure the center-to-center hole spacing on the existing adapter flange. Measure the shaft diameter and keyway size. Do not rely on the model code alone, as revisions can change these dimensions.

Step 4: Check the Plate Count

Count the number of friction discs in your existing unit:

  • 1-plate models (e.g., 118, 124WCB) engage faster and have lower torque capacity.
  • 2-plate models (e.g., 218, 236WCB) offer a balance of torque and response.
  • 3-plate models (e.g., 318, 336WCB) provide maximum torque for heavy-duty loads.

Step 5: Inspect Wear Components

If you are replacing internal parts, measure the thickness of the existing friction disc. If it is at or below the wear limit, the replacement element must include a new friction disc. For brakes, also check the wear plate surface for scoring.

Cross-Reference & Replacement

Important boundaries to avoid cross-brand errors:

  1. Wichita vs. Airflex WCB: Wichita and Airflex WCB units use different flange and port configurations. Do not assume drop-in compatibility.
  2. WPT vs. Eaton PDC: The WPT Power Grip is a drum clutch; the Eaton PDC is a disc clutch. They are not interchangeable.
  3. WPT 324SHD vs. Airflex SHD324: Both are severe-duty 24-inch clutches, but they are different brand platforms. Confirm interface measurements with HYRIG engineers.

Internal links:

Selection Support

Still not sure which replacement element fits your drawworks or clutch? Send HYRIG the existing unit's nameplate photo, shaft measurements, adapter bolt pattern, and disc thickness. Engineers will confirm the compatible element and quote with lead time.

Frequently Asked Questions

Q: How do I know if a replacement clutch will fit my shaft?
Measure the existing shaft diameter and keyway. The replacement clutch bore must match within tolerance. Send HYRIG the measurements for verification.

Q: Can I replace a Wichita clutch with an Airflex or WPT clutch?
Do not assume cross-brand compatibility. Wichita, Airflex, and WPT use different interface dimensions. Confirm measurements with HYRIG engineers before ordering.

Q: What is the lead time for a replacement clutch?
Standard lead time is quoted per order based on configuration and quantity; for urgent downtime, confirm with HYRIG engineers at inquiry.

Q: Is this an original Eaton or WPT product?
No. HYRIG supplies independent, compatible replacement products and is not affiliated with Eaton Corporation or WPT Power Corporation.

Contact

For clutch and brake replacement verification and selection support, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing unit nameplate photo
  • Shaft diameter and keyway dimensions
  • Adapter bolt pattern measurements
  • Friction disc thickness (if replacing wear parts)
  • Required quantity

Related Pages

Name:
Message:
Verification code:
Submit
Comment