HYRIG can supply the FESTO VSVA-B-B52-ZD-A1-1T1L solenoid valve. The FESTO VSVA-B-B52-ZD-A1-1T1L is a 5/2 bistable directional control valve with a standard nominal flow rate of 1100 l/min, a 26 mm valve width to ISO 15407-1, and two 24 VDC solenoids with an M12 central plug. It is used where the valve must hold its last position on power loss — bistable operation means the spool stays where it was last shifted, without a spring return, and the soft sealing principle provides tighter shut-off than a hard-sealed spool valve.
| Valve function | 5/2 bistable |
| Standard nominal flow rate | 1100 l/min |
| Valve width | 26 mm (ISO 15407-1) |
| Operating pressure | -0.9 bar … 10 bar |
| Pilot pressure | 3 bar … 10 bar |
| Supply voltage | 24 VDC |
| Electrical connection | M12 central plug |
| Protection class | IP65 / NEMA 4 |
| Sealing principle | Soft sealing |
| Weight | 276 g |
| Model | Function | Flow rate | Standard | Pressure range |
|---|---|---|---|---|
| VSVA-B-B52-ZD-A1-1T1L | 5/2 bistable, soft seal | 1100 l/min | ISO 15407-1 | -0.9-10 bar |
| VSVA-B-B52-H-A1-1R5L | 5/2 bistable, hard seal | 1100 l/min | ISO 15407-1 | 3-8 bar |
| VSVA-B-M52-MZD-A1-1T1L | 5/2 monostable, soft seal | 1100 l/min | ISO 15407-2 | -0.9-10 bar |
Explore the full range in the FESTO VSVA valve terminal overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Valve width | 26 mm |
| Pneumatic connection | Sub-base, 26 mm to ISO 15407-1 |
| Electrical connection | M12 central plug |
| Protection class | IP65 / NEMA 4 |
| Weight | 276 g |
| Operating temperature | -5 °C … +50 °C |
| Media | Compressed air to ISO 8573-1:2010 [7:4:4] |
The VSVA-B-B52-ZD-A1-1T1L is a 5/2 bistable piston spool valve with soft sealing. A momentary signal on the set solenoid shifts the spool to connect port 1 to port 4 and port 2 to port 3; a momentary signal on the reset solenoid shifts the spool back. When both solenoids are de-energized, the spool stays in its last position — the valve holds the actuator position on power loss.
The soft sealing principle uses an elastomer seal on the spool, which provides tighter shut-off and lower leakage than a hard-sealed spool valve. This is useful when the cylinder must hold a position against a load for extended periods, or when compressed air leakage would be unacceptable. The 26 mm ISO 15407-1 sub-base provides a 1100 l/min flow rate, and the operating pressure range extends to -0.9 bar, so the valve can also be used in vacuum circuits.
Not sure whether bistable soft-seal is the correct function for your holding requirement, or need the monostable variant with a defined fail-safe position? Send your actuator type, required position on power loss, acceptable leakage, and manifold standard, and we will confirm the valve function and sealing principle.
Q: What is the flow rate of the Festo VSVA-B-B52-ZD-A1-1T1L?
A: 1100 l/min standard nominal flow rate, with a valve flow rate of 1400 l/min.
Q: What is the difference between soft seal and hard seal in VSVA bistable valves?
A: Soft seal uses an elastomer on the spool, providing tighter shut-off and lower leakage for holding functions. Hard seal uses a metal-to-metal fit, which is more tolerant of contaminated air but has higher leakage.
Q: Does the VSVA-B-B52-ZD-A1-1T1L require continuous solenoid power to hold position?
A: No. Bistable operation means the spool stays in its last position without continuous power. A momentary pulse on the set or reset solenoid is sufficient to change position.
Q: What is the weight of the VSVA-B-B52-ZD-A1-1T1L?
A: 276 g, based on the configured valve without manifold accessories.
Q: What is the lead time for Festo VSVA-B-B52-ZD-A1-1T1L?
A: Standard lead time is 7–17 days from order confirmation, based on the quoted supply status.
For FESTO VSVA-B-B52-ZD-A1-1T1L selection and manifold configuration, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.