The VS2 pump is an API 610 vertical can-type multistage pump, specially built for very low NPSH plus high head critical process duties. Its can (barrel) casing maintains a flooded suction, eliminating cavitation even when pumping boiling point liquids, light hydrocarbons, or hot condensate. Below we compare the VS2 against VS1, BB4, and BB5 pumps to help you select the right pump for low NPSH high head refinery, petrochemical, or power applications.
Core Advantages of VS2 Pump
Can Barrel Structure → Built-in Suction Reserve, Ultra Low NPSH Performance
The pump is installed inside a vertical can that is connected to the suction vessel. The can maintains a flooded suction at all times, providing exceptionally low NPSH. Horizontal pumps (BB4/BB5) cannot match this performance for boiling point liquids.
Multistage Design → Achieve Ultra High Head in Compact Vertical Layout
Multiple stages (2–12+) generate heads up to 1,500 meters. Vertical configuration minimizes ground footprint – ideal for retrofits and congested plants.
Tank-Top Mounting → Save Floor Space, Simple Civil Work
The pump mounts directly on the tank nozzle or a small foundation. No large concrete baseplate, no extensive civil work.
Cartridge Rotor → Easy Pull-Out Overhaul Without Dismantling Piping
The entire rotating assembly lifts out vertically. The can casing and piping remain in place – maintenance downtime reduced significantly.
Suitable for High Temperature & High Pressure Heavy-Duty Continuous Operation
Up to 400°C and 150 bar. Liquid lubricated bearings require no external oil system.
VS2 vs VS1 (Fully Submerged Multistage Pump)
| Feature | VS2 (Can-Type) | VS1 (Fully Submerged) |
|---|---|---|
| Installation | Tank-top mounted on can | Fully submerged inside tank |
| NPSH performance | Ultra low (flooded can) | Ultra low (submerged) |
| Maintenance | Easier – rotor pulls from top without tank entry | Pull-out from top, but can requires tank access |
| Can casing | Integral part of pump | Not applicable |
| Best for | Low NPSH, high head, easy maintenance access | Deep tank, high head, simple submerged design |
Verdict: Use VS2 for easier maintenance and tank-top mounting. Use VS1 when fully submerged inside the tank is acceptable or required.
VS2 vs BB4 / BB5 (Horizontal Multistage Pumps)
| Feature | VS2 | BB4 / BB5 |
|---|---|---|
| Configuration | Vertical can-type | Horizontal (barrel or segmental) |
| NPSH requirement | Ultra low (flooded can) | Higher (requires positive suction pressure) |
| Space usage | Minimal floor space | Large footprint + baseplate |
| Suitability for boiling point liquids | Excellent (no cavitation) | Poor (cavitation likely) |
| Maintenance | Pull-out cartridge from top | Requires horizontal space for rotor removal |
Verdict: Choose VS2 when NPSH is limited (e.g., condensate, light hydrocarbons, hot liquids). Choose BB4/BB5 for applications with adequate NPSH and ample floor space.
VS2 vs Other VS Types
VS2 is the standard choice for refinery low NPSH high-head process feed. Other VS types:
VS1: Fully submerged, no can casing
VS3: Wet pit, larger flows, lower heads
VS4: Oil-lubricated bearings for dirty or high temp
VS5–VS7: Special configurations (axial flow, in-line, etc.)
Best Applications for VS2 Pump
Refinery hydrocracker feed (low NPSH light hydrocarbons)
Petrochemical reactor feed (ethylene, propylene)
Power plant condensate boosting (hot condensate near boiling point)
Any process requiring high head with available NPSH below 3 meters
Get a VS2 Pump vs VS1 / BB4 / BB5 Comparison for Your Duty
Not sure whether VS2, VS1, or horizontal BB4/BB5 is best for your low NPSH high head application? Our engineering team provides free pump selection advisory.
Send us your duty point:
Flow rate (m³/h or GPM)
Total head (m or ft)
Fluid name and temperature (°C)
Available NPSH (m or ft)
Installation preference (tank-top or foundation)
We will reply within 24 hours with:
Recommended pump type (VS2, VS1, BB4, or BB5)
Side-by-side comparison for your specific duty
Performance curve and API data sheet
Can installation drawing (2D CAD)
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1–OH6, BB1–BB5, VS1–VS7 types) serving global refineries, petrochemical plants, power utilities, and low NPSH process industries. Contact us for custom-engineered VS2 vertical can-type multistage pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.