This page presents verified field cases of our API 610 VS2 vertical can-type multistage pumps operating reliably in extremely low NPSH, high head critical services. Each case demonstrates the pump's ability to eliminate cavitation, handle high pressure, and deliver long-term stable performance in refinery, petrochemical, power, and chemical applications.
Case 1 – Refinery Hydrocracking Feed (Middle East)
Background: A refinery required a high-pressure feed pump for a hydrocracking unit. The feedstock was light hydrocarbon at near-boiling temperature, with available NPSH less than 2.5 meters. Horizontal multistage pumps experienced severe cavitation and seal failures.
VS2 Pump Solution:
Flow: 320 m³/h
Head: 1,350 m
Temperature: 210°C
Can length: 3,600 mm
Material: Alloy steel can, 316L impellers
Stages: 9
Results:
Ultra low NPSH – can-type flooded suction eliminated cavitation completely
Long-term stable operation – over 3 years without pump-related downtime
No suction piping – reduced leak points and installation complexity
Cartridge rotor – annual inspection completed without removing can casing
Available references: Can installation drawing, site photo, NPSH calculation sheet.
Case 2 – Petrochemical Reactor Feed (Southeast Asia)
Background: A petrochemical plant needed a high-pressure pump for feeding a polymerization reactor with corrosive process medium (chlorinated solvent). Required head: 1,100 m. Available NPSH was limited. Standard 316L showed pitting after short service.
VS2 Pump Solution:
Flow: 180 m³/h
Head: 1,100 m
Temperature: 120°C
Can length: 2,800 mm
Material: Duplex stainless steel (can, impeller, shaft)
Stages: 8
Seal: API 682 Plan 53B dual mechanical seal
Results:
Duplex material – withstood corrosive medium for 2+ years without pitting
High pressure resistance – 110 bar discharge pressure maintained consistently
Leak-free running – dual seal with barrier fluid achieved zero emissions
Stable operation – no cavitation despite low NPSH
Available references: Material certificate (EN 10204 3.1), installation photo, seal performance log.
Case 3 – Power Plant Condensate Boosting (Asia)
Background: A combined cycle power plant required a condensate booster pump to transfer hot condensate (85°C) from a low-level hotwell to the deaerator. The condensate was near boiling point, and horizontal pumps cavitated frequently, causing plant trips.
VS2 Pump Solution:
Flow: 280 m³/h
Head: 520 m
Temperature: 85°C
Can length: 3,200 mm
Material: Carbon steel can, stainless steel impellers
Stages: 5 (custom stage count for exact head)
Results:
High efficiency (82%) – better than previous multistage horizontal pump
Low vibration – vertical can design absorbed thermal expansion, vibration <2.0 mm/s
No cavitation – can-type flooded suction eliminated NPSH problem
24/7 continuous operation – 18 months without failure
Available references: Performance test report, vibration log, site photo.
Case 4 – Low NPSH Chemical Process (Europe)
Background: A chemical facility had a process requiring high-head transfer (450 m) of a solvent with very low vapor pressure margin. Available NPSH was only 1.8 meters. Existing pumps cavitated severely, damaging impellers and seals within weeks.
VS2 Pump Solution:
Flow: 95 m³/h
Head: 450 m
Temperature: 60°C
Can length: 2,400 mm
Material: 316L stainless steel
Stages: 4
Results:
Solved insufficient NPSH problem – can-type design provided flooded suction, complete cavitation elimination
Perfectly matched process design requirements – achieved exact head and flow
Low maintenance – after 18 months, impeller and wear rings showed minimal wear
Simple installation – tank-top mounted, no foundation, no suction piping
Available references: Installation drawing, site photo, before/after cavitation comparison.
What You Can Request From Us for Each Case
Can installation drawings (2D CAD)
Site photos and tank mounting images
Project parameter sheet (flow, head, stages, can length, material)
Performance test data and NPSH calculations
Why Real Project Cases Matter
Field references prove that our VS2 pumps deliver:
No cavitation in ultra-low NPSH refinery hydrocracker feed service
Corrosion resistance and leak-free operation in petrochemical reactor feed (duplex)
High efficiency, low vibration in power plant condensate boosting
Perfect solution for insufficient NPSH chemical processes
Get the Complete VS2 Pump Case Study Package
We can match your low NPSH high head conditions to similar successful installations. Request the VS2 pump project case PDF or ask for references in your specific industry.
Email: info@hyrig.com
Please specify your industry (refinery / petrochemical / power / chemical) and we will send relevant case studies, installation drawings, and technical data within 24 hours. We also welcome inquiries for custom VS2 vertical can-type multistage pump selection and factory direct pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.