Boiler Feed Pump – API 610 BB3 Multistage Axially Split Centrifugal Pump by Leading China 610 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 BB3 boiler feed pump (BFW pump) – horizontal, multistage, axially split, centreline‑mounted, between‑bearings centrifugal pump. Engineered for continuous high‑pressure, high‑temperature duty in power plants, industrial boilers, HRSG units, and cogeneration plants. Opposed back‑to‑back impeller arrangement for axial thrust self‑balance. Double volute casing balances radial thrust. First‑stage double‑suction impeller option for low NPSHr. API 682 mechanical seals with Plan 23 (cooled recirculation) for hot water service. Manufactured by a leading certified China API 610 pump manufacturer with API Q1 certification. Flows to 3,200 m³/h, heads to 2,900 m, pressures to 300 bar, temperatures to 205°C. 20‑year design life, 3‑year continuous operation.

Conatct For Details
DetailReview(0)Additional

Product Overview

A boiler feed pump (BFW pump) is a critical, high‑pressure, high‑flow centrifugal pump that delivers treated feedwater from the deaerator through high‑pressure heaters to the boiler drum or steam generator in power plants, industrial steam systems, cogeneration plants, and heat recovery steam generators (HRSG). Boiler feed pumps must overcome substantial resistance in the economiser, boiler drum, and piping, operating continuously at high pressures (up to 300 bar / 4,350 psi) and moderate to high temperatures (up to 205°C/400°F). The pump is classified under API 610 (ISO 13709) as Type BB3 – a horizontal, single‑casing, axially split, centreline‑mounted, between‑bearings, multistage centrifugal pump. The BB3 design is ideally suited for boiler feed service because the axially split casing allows full rotor access without disturbing suction or discharge piping. Opposed impellers produce hydraulic axial thrust self‑balance, eliminating complex balance discs or drums. Double volute stages balance radial thrust, while centreline mounting accommodates thermal expansion at elevated temperatures. This pump is manufactured by a leading China API 610 pump manufacturer with full API Q1 certification, decades of severe‑duty pumping experience, and thousands of BB3 boiler feed pumps installed in power plants and industrial boilers worldwide.

Construction & API 610 Classification

FeatureDescription
API 610 TypeBB3 (axial split, single casing, between‑bearings)
Casing formAxially split volute (horizontal split)
Casing typeSingle casing (non‑barrel)
Bearing supportBetween‑bearings – two bearing brackets at drive end and non‑drive end
Number of stages3 to 14 (depending on head requirement)
Impeller arrangementOpposed (back‑to‑back) for axial thrust self‑balance
Volute designDouble volute to balance radial thrust
Suction typeSingle‑suction first stage; double‑suction low‑NPSH option
MountingCentreline‑mounted (feet on casing centreline)
Nozzle orientationSuction and discharge nozzles integrally cast with lower half casing
ComplianceAPI 610 11th / 12th edition (ISO 13709)

Why BB3 for Boiler Feed Service

Axially split casing – The casing is split horizontally along the centreline; the upper half can be removed without disconnecting suction or discharge piping. This provides full access to the rotor, impellers, wear rings, and seal chamber – essential for boiler feed pumps that require routine inspection. All internal maintenance and replacement can be performed without removing inlet and outlet pipes.

Between‑bearings rotor – Extremely high shaft stiffness minimises deflection even at high pressures and flows, extending mechanical seal and bearing life.

Opposed back‑to‑back impellers – Successive stages are arranged in opposing directions. Each pair of opposite‑facing impellers generates equal and opposite axial thrust. The complete rotor is hydraulically self‑balanced without complex balance discs, drums, or thrust bearings – eliminating components that wear or foul. Opposed impellers are especially good for transferring liquids that may contain particles.

Double volute diffuser design – Each stage contains double volute passages symmetrically arranged along the centreline; radial hydraulic forces are self‑balanced over the entire operating range, reducing shaft deflection and increasing reliability. The double‑volute design balances radial rotor loads at all capacities, optimising unit reliability.

Centreline mounting – Feet are located on the casing centreline; the casing expands uniformly when handling hot boiler feedwater (up to 205°C), preventing shaft misalignment and bearing distress. Symmetrical casing parts and centreline‑located feet ensure uniform temperature expansion of the casing and stability with high‑temperature liquids.

First‑stage double‑suction impeller option – A double‑suction first stage impeller is available for low‑NPSH service when available NPSHa is limited (e.g., low deaerator elevation). The double‑suction impeller reduces NPSH required (NPSHr) by 30‑40%. Suction and discharge nozzles are integrally cast with the lower half casing to permit pump disassembly and rotor removal without disturbing piping connections.

Single casing (non‑barrel) construction – For boiler feed service up to 150‑250 bar, the single casing BB3 is suitable. For extreme ultra‑supercritical pressures (>250 bar), BB5 barrel pumps are typically specified. Within this range, BB3 offers easier maintenance access.

Hydraulic axial thrust self‑balance – Back‑to‑back arranged impellers provide rotor axial balance, lowering wear of rotating elements. Two‑row rotors with opposed impellers provide axial balance over the entire operating range. The design avoids complex balancing discs – especially beneficial for liquids that may contain solid particles.

Radial thrust self‑balance – Double volute type flow channels symmetrically arranged along the centreline.

Key Technical Specifications (Boiler Feed Duty)

ParameterRange
Flow10 – 3,200 m³/h (44 – 14,000 GPM) – Sulzer MSD
Head20 – 2,900 m (65 – 9,500 ft)
Discharge pressureUp to 300 bar (4,350 psi) – 250 bar typical for subcritical boilers
Temperature-80°C to +205°C (-112°F to +400°F) – –10 to +200°C typical BFW range
Number of stages3 – 14
SpeedUp to 6,000 rpm (Sulzer MSD) – 2,950 rpm typical for 50Hz direct drive
Flange ratingANSI Class 600 / 900 / 1500 / 2500
Axial thrust balanceOpposed back‑to‑back impellers (hydraulic self‑balance)
Radial thrust balanceDouble volute casing
Design life20 years minimum

Boiler Feed Duty – Process Characteristics

System context – A typical boiler feed pump takes suction from a deaerator (at atmospheric or slight positive pressure) where feedwater has been heated to approximately 100‑150°C and deaerated to remove oxygen. The pump pushes water through high‑pressure heaters and an economiser into the boiler drum at final pressure. The major characteristic of boiler feed pumps is their high differential head. Dependent on FPSO design, a booster pump is often required to export crude delivered to deck level.

Hydraulic head – Subcritical drum boilers typically require 100‑200 bar discharge pressure; supercritical once‑through boilers require >250 bar. Because boiler feed water is hot and near its bubble point, available NPSH is limited, and cavitation is a constant risk. The first‑stage impeller is specifically designed with a large eye, low‑suction‑specific speed geometry, and optional double suction to minimise NPSHr. An inducer is also available for extremely low NPSH.

Thermal expansion – The casing is centreline‑mounted, allowing the pump to expand uniformly with temperature, maintaining alignment with the driver. Symmetrical casing parts and centreline‑located feet ensure uniform temperature expansion of the casing and stability in high‑temperature liquids.

Minimum flow – During start‑up and low load, the pump must be protected by an automatic recirculation valve (ARC) or continuous bypass line to maintain minimum flow (typically 20‑30% of BEP flow), preventing overheating, cavitation, and seal damage. The ARC typically returns minimum flow to the deaerator.

Materials – API 610 Table H for Boiler Feed Water

Boiler feed water is typically treated, deaerated, and may contain low levels of ammonia, hydrazine (oxygen scavenger), or other chemicals. Carbon steel is acceptable for moderate pressures at moderate temperatures. For supercritical service (>250 bar) or with aggressive water chemistry, upgrade to stainless steel or duplex wetted parts.

ComponentStandard MaterialUpgrade OptionAPI 610 Class
CasingCarbon steel (Class II)316L SS (S‑8)C‑6
ImpellersCarbon steel or 304 SS316L SS (S‑8)C‑6 / S‑8
Shaft4140 hardened steel17‑4 PH / duplexC‑6 / A‑8 / D‑1
Wear ringsHardened 4140316L SS + Stellite hard‑faced–
Interstage bushingsHardened 4140316L SS + Stellite–
Fasteners4140 (B7)B8M (316) / duplex–
Gaskets / O‑ringsSpiral wound graphitePTFE / Grafoil–

Materials for Boiler Feed Service

For most subcritical boiler feed pumps, carbon steel (C‑6) wetted parts are sufficient, economical, and widely used. Hot, deaerated water at up to 200°C does not aggressively corrode carbon steel. However, for supercritical service (>250 bar), high‑strength forged low‑alloy steel (Class II) casings with stainless steel clad internal components are specified. For aggressive water chemistry (high chlorides, low pH), upgrade to 316L stainless steel (S‑8) or duplex (D‑1). NACE MR0175 is not typically required for boiler feed water (no H₂S).

All materials supplied with EN 10204 Type 3.1 certification and full traceability.

Mechanical Seals – API 682 Plan 23 for Hot Boiler Feed Water

Boiler feed water at high temperature (150‑200°C) and pressure requires specialised sealing. Standard Plan 11 self‑flush is insufficient because hot water flashes across seal faces, causing vapourisation, dry running, and rapid seal failure. Plan 23 (recirculation with external cooler) is the most common seal plan for high‑temperature boiler feed service.

Seal ArrangementAPI 682 PlanSuitability for Boiler Feed
Single seal with recirculation coolerPlan 23Standard – fluid recirculates from the seal chamber through an external cooler and back, maintaining seal face temperature below vapourisation point
Single seal with quenchPlan 23 + Plan 62Steam or water quench on atmosphere side – condenses any vapour leakage
Tandem sealPlan 52For higher pressure (>150 bar) or critical service – backup seal contains pressure if primary seal fails
Dual pressurised (Arrangement 3)Plan 53BZero leakage for hazardous fluids; not normally used for boiler feed water

Plan 23: A closed loop continuously circulates fluid from the seal chamber through an external cooler (air‑cooled or water‑cooled), returning cooled fluid to the seal. The seal chamber is thus always filled with cool, liquid‑phase water, preventing flashing. The external cooler is properly piped to ensure continuous circulation.

Recommended seal faces: Silicon carbide vs. carbon (standard). For higher reliability in abrasive service (e.g., iron oxide particles), silicon carbide vs. silicon carbide (hard‑on‑hard). Elastomers: Viton (FKM) – handles up to 200°C.

NPSH and Suction Conditions

Boiler feed pumps typically take suction from a deaerator with limited NPSHa (3‑6 metres only, as deaerators are often at atmospheric pressure with the water level just above pump centreline). To prevent cavitation:

  • Double‑suction first‑stage impeller is strongly recommended when NPSHa ≤ 5 metres. Many BB3 pumps offer first‑stage double‑suction design. A double‑flow first‑stage impeller is available to reduce the NPSH required. The first‑stage impeller can be designed as single‑suction or double‑suction depending on user requirements.

  • Low‑NPSH hydraulic design with large eye, low‑suction‑specific speed impeller profile. Excellent suction capability due to double‑suction first‑stage NPSH impeller.

  • Inducer optional for extremely low NPSHa (deaerator < 3 metres elevation). The inducer is an axial flow stage mounted before the first radial impeller, raising pressure at the impeller eye and reducing NPSHr by 40‑60%.

  • Ensure NPSHa ≥ NPSHr + 1.0 m per API 610.

Applications – BB3 Boiler Feed Pump

Industry / SettingSpecific Service
Fossil fuel power plants (coal, gas, oil)Subcritical drum boiler feed
Supercritical and ultra‑supercritical power plantsOnce‑through boiler feed (may require BB5 barrel)
Combined cycle gas turbine (CCGT) / HRSGHigh‑pressure and intermediate‑pressure drum feed
Biomass and waste‑to‑energy power plantsSmall/medium boiler feed
Industrial boilersProcess steam boilers in refineries, petrochemical plants, paper mills, food processing
Cogeneration (CHP) plantsSimultaneous power and process steam generation
Nuclear power plantsNuclear auxiliary boiler feed and safety‑related high‑pressure services
Desalination plantsBoiler feed for steam‑driven evaporators

Why Choose an API 610 BB3 Boiler Feed Pump from This China Manufacturer

  • Full API 610 compliance (BB3) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.

  • Axially split casing – Maintenance without removing piping; full rotor access in hours (complete pump core replacement within 8 hours).

  • Between‑bearings high‑rigidity rotor – Low vibration, extended bearing and seal life even at high pressure.

  • Opposed back‑to‑back impellers – Hydraulic axial thrust self‑balance eliminates balance discs, drums, and complex thrust bearings – one of the most distinctive and valued features of the BB3 design.

  • Double volute casing – Radial thrust self‑balance over entire operating range; reduces shaft deflection and bearing load.

  • Centreline mounting – Accommodates thermal expansion at up to 205°C; prevents misalignment and bearing distress.

  • API 682 Plan 23 – External cooler recirculates cool fluid around seal faces; prevents flashing in high‑temperature boiler feed service.

  • Low NPSH options – Double‑suction first‑stage impeller and inducer options available for low‑NPSHa deaerators.

  • Broad hydraulic coverage – Flows to 3,200 m³/h, heads to 2,900 m, pressures to 300 bar.

  • Material flexibility – Carbon steel (C‑6) for standard boiler feed; 316L SS (S‑8) / duplex (D‑1) for aggressive water chemistry.

  • Certified China manufacturer – API Q1, ISO 9001, with global references and export experience.

  • Proven in boiler feed service – Thousands of BB3 pumps operating in power plants and industrial steam systems worldwide.

Quality Assurance & Testing (Per API 610)

  • Hydrostatic test – Casing tested at 1.5× MAWP.

  • Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).

  • Mechanical run test – 4 hours minimum continuous operation at rated speed; vibration and bearing temperature recorded and certified within API 610 limits.

  • NPSH test – Optional, when specified.

  • Impeller dynamic balancing – Grade G6.3 or better.

  • Material certification – EN 10204 3.1 for all pressure‑containing components; Positive Material Identification (PMI) available.

  • NDE – Dye penetrant on castings; ultrasonic on shafts; as required by API 610.

  • Third‑party inspection – Available (DNV, Lloyds, BV, SGS).

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (API 682 Plan 23 ready)1 set
Bearing set (radial cylindrical + angular contact thrust)1 set
Wear ring set (casing + impeller)1 set
Interstage bushings1 set
Impeller set (first stage + succeeding stages)1 set (for critical duty)
Shaft (for critical duty)1
Gasket / O‑ring kit (full set)1 set
Inducer (if fitted)1 set

Get a Quote or Engineering Support

For detailed selection of the correct API 610 BB3 boiler feed pump for your power plant or industrial boiler project – including flow, head, boiler operating pressure, feedwater temperature, deaerator NPSHa, material selection (carbon steel vs. stainless steel), and API 682 seal plan – please contact our engineering team.

Email: info@hyrig.com

Our API 610 BB3 boiler feed pumps are specifically engineered for the most demanding high‑pressure, high‑temperature boiler feed service – handling up to 300 bar and 205°C with proven reliability. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with axially split casing, opposed impeller axial balance, double volute radial balance, and Plan 23 seal cooling.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit