The cold crystallization / salting out feed pump is a specialised centrifugal pump designed to feed high‑chloride brine into the cold crystallization and salting out sections of ammonium chloride (NH₄Cl) production – typically in Hou`s process (combined process / Union process) soda ash plants. After the mother liquor is cooled or treated with salt to reduce the solubility of NH₄Cl, crystals form in the crystallizer. The feed pump transfers the brine containing entrained NH₄Cl crystals from the crystallizer feed tank or mixing vessel to the crystallizing equipment (e.g., cooling crystallizer or salting out vessel).
This service is challenging due to:
High chloride concentration (Cl⁻ 60,000 – 100,000 ppm) – extremely corrosive to standard stainless steels, requiring high‑performance alloys.
Moderate low temperature (20‑40°C) – not cryogenic, but still requiring careful material selection.
Entrained NH₄Cl crystals (5‑15%) – abrasive, causing wear on seal faces, wear rings, and impellers.
Corrosive ammonia – free ammonia in the brine attacks copper alloys and some elastomers.
The pump is classified under API 610 (ISO 13709) as Type OH1 – an overhung, foot‑mounted, radially split, single‑stage centrifugal pump. The foot‑mounted design (OH1) is suitable for the moderate temperature range (20‑40°C) and provides a robust, accessible configuration with back pull‑out for easy seal and impeller maintenance.
This pump is manufactured by a leading China API 610 pump manufacturer with full API Q1 certification, extensive experience in corrosion‑resistant alloys, and thousands of OH1 pumps operating in ammonium chloride crystallization circuits worldwide.
| Feature | Description |
|---|---|
| API 610 Type | OH1 (overhung, foot‑mounted, radially split, single‑stage) |
| Casing form | Radially split volute, foot‑mounted |
| Bearing support | Overhung – impeller overhangs from bearing housing; bearings at drive end only |
| Number of stages | Single stage |
| Suction type | End suction, single‑suction |
| Discharge orientation | Top (standard) or side |
| Flange rating | ANSI Class 150 / 300 |
| Compliance | API 610 11th / 12th edition (ISO 13709) |
Foot‑mounted simplicity – Temperature 20‑40°C is well within the capability of foot‑mounted pumps; no need for centreline mounting.
Overhung design – Compact, easy to maintain, with back pull‑out capability.
Radially split casing – Provides good pressure containment and allows access to the rotor.
Back pull‑out design – The entire rotating assembly can be removed without disconnecting piping – essential for pumps that require frequent seal replacement due to abrasive crystals.
Single‑stage open passages – Wide internal flow paths allow entrained NH₄Cl crystals to pass without clogging.
| Parameter | Design Range |
|---|---|
| Flow rate | 50 – 400 m³/h (220 – 1,760 GPM) |
| Head | 30 – 80 m (98 – 260 ft) |
| Fluid temperature | 20 – 40°C (68 – 104°F) |
| Fluid composition | NH₄Cl brine (25‑28%), NaCl, free ammonia, fine NH₄Cl crystals |
| Chloride concentration | 60,000 – 100,000 ppm (6‑10% Cl⁻) |
| Solids content | 5‑15% fine NH₄Cl crystals (entrained) |
| Specific gravity | 1.10 – 1.20 |
| pH | 7 – 9 (ammoniacal) |
| Maximum pressure | 1.5 – 2.5 MPa (15 – 25 bar) |
| Speed | 1,450 / 2,900 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz) |
| NPSHr | Optimised (<3‑5 m) – inducer option for low NPSHa |
| Pump efficiency | 65‑78% (depending on size and crystal loading) |
| Design life | 20 years minimum |
Standard 316L is not sufficient for prolonged exposure to Cl⁻ > 50,000 ppm at 20‑40°C. Duplex 2205 is the recommended material for its excellent pitting resistance (PREN 35‑38) and resistance to chloride stress corrosion cracking.
| Component | Recommended Material | API 610 Class |
|---|---|---|
| Casing | Duplex 2205 | D‑1 |
| Impeller | Duplex 2205 | D‑1 |
| Shaft | Duplex 2205 or 17‑4 PH (coated) | D‑1 / A‑8 |
| Wear rings | Duplex 2205 + Stellite hard‑facing | – |
| Seal chamber | Duplex 2205 | D‑1 |
| Fasteners | Duplex 2205 | – |
| Gaskets / O‑rings | PTFE or Viton (FKM) | – |
Pitting Resistance Equivalent Number (PREN) 35‑38 – far superior to 316L (PREN 25‑30).
High strength – yield strength approx. 450‑620 MPa, twice that of 316L, allowing lighter and more rigid construction.
Resistance to chloride stress corrosion cracking (SCC) – 316L is susceptible to SCC above 60°C; at 20‑40°C, the risk is lower, but duplex provides a wider safety margin.
Proven in NH₄Cl service – Duplex 2205 is widely used in ammonium chloride crystallizer feed pumps worldwide.
All materials supplied with EN 10204 Type 3.1 certification and full traceability.
The feed brine contains 5‑15% fine NH₄Cl crystals, which are abrasive and can quickly destroy standard seal faces. External clean flush is essential.
| Seal Arrangement | API 682 Plan | Suitability |
|---|---|---|
| Single seal with external clean flush | Plan 32 | Highly recommended – continuous injection of clean external fluid (clarified NH₄Cl solution or warm water) at 1‑2 bar above pump suction pressure flushes crystals away from seal faces |
| Dual pressurised (Arrangement 3) | Plan 53B | Zero emissions, but barrier fluid alone does not flush solids – must be combined with Plan 32 or a separate flush |
| Single seal with quench | Plan 62 | Not sufficient for crystalline slurries |
Silicon carbide vs. tungsten carbide – Tungsten carbide >1,800 Hv, highly resistant to abrasion from NH₄Cl crystals.
Tungsten carbide vs. tungsten carbide – Ultimate abrasion resistance for high solids (15%+).
Elastomers: Viton (FKM) – compatible with NH₄Cl brine and ammonia at 20‑40°C; Aflas or Kalrez for superior chemical resistance.
Critical design: The external flush (Plan 32) must be continuous and at a sufficient flow rate (5‑15 L/min) to prevent crystals from entering the seal chamber. The flush fluid should be clean, compatible, and preferably warmed slightly (to prevent local cooling that could cause salt precipitation).
The feed pump often takes suction from a crystallizer feed tank or mixing vessel with limited liquid head (2‑4 metres). To prevent cavitation:
Low NPSHr impeller design – Optimised inlet geometry.
Inducer option – Reduces NPSHr by 40‑60%; highly recommended when NPSHa < 3 m.
Suction pipe sizing – Keep suction piping short, straight, and at least equal to pump suction diameter.
| Industry | Specific Service |
|---|---|
| Soda ash (Hou`s / Union process) | Feed to cold crystallizer for NH₄Cl precipitation; feed to salting out vessel | | |
| Ammonium chloride production | Crystallizer feed pump; slurry transfer to centrifuge or filter |
| Potash / fertilizer | Similar high‑chloride crystallization feed services |
API 610 full compliance (OH1) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.
Duplex 2205 wetted parts – Superior resistance to high chloride pitting and crevice corrosion (PREN 35‑38).
Designed for crystalline slurries – Wide internal passages, abrasion‑resistant seal faces, and Plan 32 external flush standard.
API 682 Plan 32 ready – External clean flush prolongs seal life dramatically in abrasive NH₄Cl crystal service.
Back pull‑out maintenance – Replace seals and wear rings without removing piping, minimising downtime.
Low NPSH options – Inducer or double‑suction first stage for low NPSHa installations.
Broad hydraulic coverage – Flows 50‑400 m³/h, heads 30‑80 m, covering all crystallizer feed duties.
Certified China manufacturer – API Q1, ISO 9001, with global references in soda ash and chemical industries.
Proven in NH₄Cl service – Thousands of OH1 pumps operating in ammonium chloride crystallization and salting out circuits worldwide.
Hydrostatic test – Casing tested at 1.5× MAWP.
Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).
Mechanical run test – 4 hours minimum; vibration and bearing temperature recorded.
NPSH test – Optional, when specified.
Impeller dynamic balancing – Grade G6.3 or better.
Material certification – EN 10204 3.1 for duplex components; PMI available for alloy verification.
NDE – Dye penetrant on castings; ultrasonic on shafts as required.
Third‑party inspection – Available (DNV, Lloyds, BV, SGS).
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 32 ready, tungsten carbide faces) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Impeller (for critical duty) | 1 set |
| Shaft (for critical duty) | 1 |
| Gasket / O‑ring kit (full set) | 1 set |
For a detailed selection of the API 610 OH1 cold crystallization / salting out feed pump for your NH₄Cl production or Hou`s process soda ash plant – including flow, head, chloride concentration, crystal loading, crystallizer feed tank NPSHa, material (Duplex 2205), and API 682 seal plan (Plan 32 with tungsten carbide) – please contact our engineering team.
Email: info@hyrig.com
*Our API 610 OH1 cold crystallization / salting out feed pumps are specifically engineered for the most demanding high‑chloride, crystalline NH₄Cl feed service – handling Cl⁻ up to 100,000 ppm with entrained crystals at 20‑40°C. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with duplex 2205 wetted parts, Plan 32 external flush, and back pull‑out design for easy maintenance.*
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.