The high pressure ammonium chloride mother liquor transfer pump is a heavy‑duty, high‑head centrifugal pump specifically designed for transferring NH₄Cl mother liquor at elevated pressures in soda ash production plants using Hou`s process (combined process / Union process). After ammonium chloride crystallization, the mother liquor – a highly concentrated brine containing NH₄Cl, NaCl, free ammonia, and fine entrained crystals – must be pumped to downstream processes such as ammonia recovery, dechlorination, or salt recovery. These services often require high discharge pressure (up to 10‑20 MPa / 100‑200 bar) to overcome system resistance or to feed elevated vessels.
This service is extremely demanding due to:
High chloride concentration (Cl⁻ 60,000‑100,000 ppm) – highly corrosive, requiring premium alloys.
High discharge pressure – requires robust pump construction with between‑bearings support.
Entrained NH₄Cl crystals (5‑15%) – abrasive, causing seal and wear ring wear.
Corrosive ammonia – attacks copper alloys and some elastomers.
The pump is classified under API 610 (ISO 13709) as Type BB2 – a radially split, single‑stage or two‑stage, between‑bearings centrifugal pump. The BB2 design places two bearings, one on each side of the impeller(s), providing excellent rotor rigidity and stability under high pressure. The radially split casing (barrel type) offers superior pressure containment compared to axially split pumps, making BB2 the preferred configuration for high‑pressure transfer duties.
This pump is manufactured by a leading China API 610 pump manufacturer with full API Q1 certification, extensive experience in corrosion‑resistant alloys, and thousands of BB2 pumps operating in high‑pressure chemical services worldwide.
| Feature | Description |
|---|---|
| API 610 Type | BB2 (radially split, between‑bearings single‑stage or two‑stage) |
| Casing form | Radially split (barrel type) for high pressure containment |
| Bearing support | Between‑bearings – bearings at both drive end and non‑drive end |
| Number of stages | Single‑stage (typical) or two‑stage (for higher head) |
| Suction type | End suction, single‑suction |
| Discharge orientation | Top or side discharge |
| Flange rating | ANSI Class 600 / 900 / 1500 / 2500 (as required) |
| Pressure rating | Up to 20 MPa (200 bar) – higher on request |
| Compliance | API 610 11th / 12th edition (ISO 13709) |
Between‑bearings rotor – Extremely high shaft stiffness, ideal for high pressure operations. Minimises deflection and vibration, extending seal and bearing life.
Radially split (barrel) casing – Provides superior pressure containment compared to axially split casings. Essential for pressures above 10 MPa (100 bar).
Excellent high pressure capability – The BB2 design can be rated for pressures up to 300 bar or more, far exceeding the requirements of mother liquor transfer.
Stable operation at high head – Single‑stage or two‑stage configurations allow heads up to 400 m without multistage complexity.
Heavy‑duty bearings – Designed for high radial loads; L10 life ≥25,000 hours.
API 682 seal chamber – Accepts high‑pressure seal arrangements.
| Parameter | Design Range |
|---|---|
| Flow rate | 50 – 1,000 m³/h (220 – 4,400 GPM) |
| Head | 100 – 400 m (330 – 1,300 ft) |
| Discharge pressure | Up to 20 MPa (200 bar / 2,900 psi) – higher on request |
| Fluid temperature | 20 – 50°C (68 – 122°F) |
| Fluid composition | NH₄Cl brine (25‑28%), NaCl, free ammonia, fine NH₄Cl crystals |
| Chloride concentration | 60,000 – 100,000 ppm (6‑10% Cl⁻) |
| Solids content | 5‑15% fine NH₄Cl crystals (entrained) |
| Specific gravity | 1.10 – 1.20 |
| pH | 7 – 9 (ammoniacal) |
| Speed | 1,450 / 2,950 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz) |
| NPSHr | Optimised (<4‑6 m) – inducer option for low NPSHa |
| Pump efficiency | 65‑80% (depending on size and head) |
| Design life | 20 years minimum |
At high pressure, the risk of chloride stress corrosion cracking (SCC) and pitting increases. High‑performance alloys are mandatory.
| Component | Recommended Material | API 610 Class | PREN |
|---|---|---|---|
| Casing (barrel) | Duplex 2205 or Super Duplex 2507 | D‑1 / D‑2 | 35‑42 |
| Impeller | Duplex 2205 or Super Duplex 2507 | D‑1 / D‑2 | 35‑42 |
| Shaft | Duplex 2205 or Super Duplex 2507 | D‑1 / D‑2 | – |
| Wear rings | Duplex 2205 + Stellite / tungsten carbide | – | – |
| Seal chamber | Duplex 2205 or Super Duplex | D‑1 / D‑2 | – |
| Fasteners | Duplex or super duplex | – | – |
| Gaskets | PTFE or spiral wound graphite (for high pressure) | – | – |
For Cl⁻ 60,000‑80,000 ppm, moderate pressure (<10 MPa) → Duplex 2205 (D‑1) is sufficient and cost‑effective.
For Cl⁻ >80,000 ppm, or pressure >15 MPa, or risk of SCC → Super Duplex 2507 (D‑2 / U‑8) is recommended for its higher PREN (>40) and superior SCC resistance.
All materials must be impact tested for low temperature (if required) and supplied with EN 10204 Type 3.1 certification.
NACE MR0175 is not typically required for NH₄Cl service (no H₂S), but can be provided on request.
High pressure combined with abrasive NH₄Cl crystals demands a robust sealing solution. The BB2 pump’s seal chamber is designed to API 682.
| Seal Arrangement | API 682 Plan | Suitability for this service |
|---|---|---|
| Dual pressurised (Arrangement 3) | Plan 53B | Recommended – zero emissions; bladder accumulator ensures barrier pressure > process; barrier fluid must be compatible and may need cooling |
| Dual pressurised with external flush | Plan 53B + Plan 32 | Ideal – adds external clean flush (Plan 32) to wash away crystals before they reach the seal faces |
| Tandem seal (Arrangement 2) | Plan 52 | Acceptable for lower pressure (<10 MPa) but less reliable for high solids |
Tungsten carbide vs. tungsten carbide – Extremely hard (>1,800 Hv), best abrasion resistance for NH₄Cl crystals.
Silicon carbide vs. tungsten carbide – Also suitable; tungsten carbide on one side for abrasion.
Elastomers: Viton (FKM) or Aflas – resistant to ammonia and chlorides at 20‑50°C.
Important: For high pressure service (above 10 MPa / 100 bar), the seal faces must be rated for the differential pressure. Use a balanced seal design.
Radially split barrel casing – Forged or fabricated from high‑strength duplex stainless steel.
Heavy‑duty between‑bearings support – Large diameter bearings, forced oil lubrication (optional).
Thick wall casing – Designed for pressure containment with safety factor per ASME VIII / API 610.
High pressure flanges – ANSI Class 600, 900, 1500, or 2500 as required.
Non‑sparking construction – All wetted parts are stainless steel / duplex; no copper alloys.
| Industry | Specific Service | Typical Pressure |
|---|---|---|
| Soda ash (Hou`s / Union process) | High pressure mother liquor transfer to ammonia recovery column | 10‑20 MPa | | ||
| Ammonium chloride production | Pressurized transfer to dechlorinator or salt recovery | 5‑15 MPa |
| Chemical processing | High pressure brine transfer for injection or reaction feed | 10‑20 MPa |
API 610 full compliance (BB2) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous operation.
Radially split barrel design – Superior high pressure containment, safe and reliable.
Between‑bearings rotor – Extremely rigid, low vibration, long bearing life even at high pressure.
Duplex / super duplex materials – Excellent resistance to chloride pitting, SCC, and erosion.
High pressure rated – Up to 20 MPa (200 bar) or higher; ANSI Class 1500/2500 flanges.
API 682 Plan 53B + Plan 32 seals – Zero emissions + external clean flush for crystal handling.
Broad hydraulic coverage – Flows 50‑1,000 m³/h, heads 100‑400 m.
Certified China manufacturer – API Q1, ISO 9001, with global references in high pressure chemical transfer.
Proven in NH₄Cl service – Thousands of BB2 pumps operating in high pressure mother liquor transfer worldwide.
Hydrostatic test – Casing tested at 1.5× MAWP (up to 30 MPa).
Performance test – Water at rated speed per API 610 Grade 2 (Grade 1 optional).
Mechanical run test – 4 hours minimum; vibration and bearing temperature recorded.
High pressure seal test – Seal chamber tested with barrier fluid at operating pressure.
Impeller dynamic balancing – Grade G6.3 or better.
Material certification – EN 10204 3.1 for all pressure‑containing components; PMI available.
NDE – 100% ultrasonic on casing forging; dye penetrant on cast impellers.
Third‑party inspection – Available (DNV, Lloyds, BV, SGS).
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 53B + Plan 32 ready, tungsten carbide faces) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Impeller | 1 set |
| Shaft | 1 (for critical duty) |
| Gasket / O‑ring kit (full set) | 1 set |
For a detailed selection of the API 610 BB2 high pressure ammonium chloride mother liquor transfer pump for your Hou`s process soda ash plant or NH₄Cl production facility – including flow, head, discharge pressure required, chloride concentration, crystal loading, NPSHa, material (Duplex 2205 vs. Super Duplex 2507), and API 682 seal plan (Plan 53B + Plan 32) – please contact our engineering team.
Email: info@hyrig.com
*Our API 610 BB2 high pressure ammonium chloride mother liquor transfer pumps are specifically engineered for the most demanding high pressure, high chloride NH₄Cl transfer service – handling up to 20 MPa with entrained crystals. Manufactured by a leading China API 610 pump manufacturer, API Q1 certified, with duplex / super duplex wetted parts, radially split barrel casing for pressure containment, and API 682 dual seals with external flush.*
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.