Casappa Gear Pumps FAQ | Selection, Pressure, Lead Time

2026-11-06 12:15

Casappa Gear Pumps FAQ | Selection, Pressure, Lead Time

HYRIG can supply Casappa PLP gear pumps and PLM gear motors. This FAQ covers common questions about selection, pressure ratings, model codes, lead time, and replacement support for the Casappa Polaris range.

Key Facts

ParameterValue
Series coveredPLP 10, PLP 20, PLP 30, PLM 10, PLM 20, PLM 30
Displacement range1.07–91.10 cm³/rev
Max pressure130–260 bar (varies by model)
Max speed2000–4000 min⁻¹ (varies by model)
Seal optionsBuna N (standard), Viton
Rotation optionsS, D, R, L, B

Frequently Asked Questions

Q: What is the difference between PLP and PLM series?
A: PLP series are gear pumps (convert mechanical power to hydraulic flow). PLM series are gear motors (convert hydraulic flow to mechanical rotation and torque).

Q: What is the maximum pressure of the Casappa Polaris range?
A: The PLP and PLM series handle up to 250 bar continuous pressure for most models, with PLM 10 rated up to 260 bar and larger displacements rated down to 130–150 bar.

Q: How do I choose the right displacement?
A: Match the cm³/rev to your required flow rate at operating speed. Use Q = V × n × ηv / 1000 (L/min), where V is displacement (cm³/rev), n is speed (RPM), and ηv is volumetric efficiency (≈0.97).

Q: How do I calculate motor torque?
A: Use M = Δp × V × ηm / 62.83 (Nm), where Δp is pressure drop (bar), V is displacement (cm³/rev), and ηm is mechanical efficiency (≈0.85).

Q: What does the R suffix mean in the model code?
A: R indicates reversible rotation with external drain. Other options: S (left-hand rotation), D (right-hand rotation), L (reversible side external drain), B (reversible internal drain).

Q: Can I replace an older Casappa pump with a current model?
A: Yes, in most cases. Verify displacement, flange bolt pattern, shaft type, port threads, and rotation direction match your existing unit. Contact HYRIG with your old part number or nameplate details for confirmation.

Q: What is the lead time for Casappa gear pumps?
A: Standard lead time is 4–6 weeks for most configurations. Urgent downtime situations can be prioritized — contact HYRIG with your required delivery date.

Q: What seal options are available?
A: N (Buna N standard) and V (Viton for high temperature). Shaft seal options: D (standard wiper), H (high pressure), C (high pressure + wiper).

Q: How do I order a multiple pump configuration?
A: Specify the stage displacements in order from drive end to rear (e.g., PLP 20/10 = PLP 20 at drive end, PLP 10 at rear). Confirm total torque does not exceed the drive shaft maximum. See Casappa Multiple Gear Pumps.

Q: Can HYRIG support repair or replacement of a complete unit?
A: Yes. HYRIG supplies complete Casappa PLP and PLM series units. Send us the nameplate details and we will confirm the correct replacement configuration.

Selection Support

Not sure which Casappa series or displacement fits your system? Send HYRIG your required flow rate (L/min), operating pressure (bar), and mounting constraints. Our engineers will confirm the correct model code and configuration.

Contact

For Casappa gear pump and motor selection, contact HYRIG: info@hyrig.com

Explore: Casappa PLP 10 Gear Pumps, Casappa PLP 20 Gear Pumps, Casappa PLP 30 Gear Pumps, Casappa PLM 10 Gear Motors, Casappa PLM 20 Gear Motors, Casappa PLM 30 Gear Motors, Casappa How to Order.

Name:
Message:
Verification code:
Submit
Comment