A self‑priming pump is a centrifugal pump that can automatically evacuate air from the suction line and fill itself with liquid without manual priming. Conventional centrifugal pumps must be flooded before start‑up – the casing and suction line must be completely filled with liquid. They also require a foot valve on the suction line. When the pump is installed above the liquid level, the line drains back after shutdown, requiring manual repriming – an inconvenient and hazardous operation when handling corrosive or flammable fluids.
This API 610 petrochemical self‑priming pump completely solves this problem. The casing has a special design: the suction nozzle is located above the impeller centreline, so a measured volume of liquid remains in the casing after shutdown. Restarting the pump creates a gas‑liquid mixture that passes through an integral separation chamber. Air is expelled while liquid recirculates to the impeller eye. This cycle repeats until the suction line air is evacuated and atmospheric pressure pushes liquid into the pump – automatic priming. The entire self‑priming process takes only tens of seconds, with suction lift capability up to 9 metres.
This pump is a single‑stage, horizontal, radially split volute pump, foot‑mounted or centreline‑mounted – a true API 610 process pump. Materials are selected according to service conditions: high‑grade stainless steel or carbon steel for wetted parts. The shaft seal is a cartridge single or double mechanical seal, and seal piping follows API standards, ensuring reliability in high‑temperature, high‑pressure and corrosive services.
The self‑priming process has three stages:
Mixing stage: The impeller rotates at high speed, mixing the stored liquid in the casing with air from the suction line, creating a gas‑liquid mixture.
Separation stage: The mixture enters the gas‑liquid separation chamber (the enlarged upper passage in the casing). Because gas and liquid have different densities, air rises and is vented to atmosphere, while liquid sinks back to the suction chamber for the next cycle.
Suction stage: With each cycle, air in the suction line is progressively removed, creating a partial vacuum. Atmospheric pressure pushes liquid from the source up the suction line. Finally, the casing and suction line are fully flooded, and the pump operates as a normal centrifugal pump.
According to the structural differences of self‑priming mechanisms, pumps are classified as gas‑liquid mixing type (internal or external recirculation), water‑ring type, or jet type. This series uses an optimised gas‑liquid mixing design, offering strong self‑priming capability and short priming time.
This self‑priming pump is fully designed and manufactured according to API 610 (ISO 13709), covering both OH1 and OH2 overhung pump types. Main construction features:
Single‑stage end‑suction overhung design: Axial suction, radial discharge – conforms to general process pump specifications.
Radially split volute casing: Foot‑mounted (OH1) or centreline‑mounted (OH2).
Self‑venting design: Casing structure with integral gas‑liquid separation. Double volute casing for DN80 and larger – balances radial forces.
Back pull‑out design: Maintenance without removing suction or discharge piping – greatly reduces downtime.
Standardised connections: Flanges to ANSI/HG/DIN/JIS international standards.
Optional heating/cooling jacket: Casing and seal chamber can be provided with cooling or heating jackets for high‑temperature (cold insulation) or cryogenic service, or where ambient temperature is extreme.
| Parameter | Range |
|---|---|
| Flow range | 0.8 – 2,600 m³/h |
| Head range | 8 – 330 m |
| Working pressure | 2.5 – 5.0 MPa |
| Working temperature | –80°C to +450°C |
| Suction lift | Up to 9 m (at sea level) |
| Flange size | DN25 – DN300 |
Special note on API 610 compliance: API 610 does not define a specific “self‑priming pump” type, but self‑priming can be achieved in two ways:
Option A (integral self‑priming casing): A standard API 610 (OH1/OH2) high‑performance centrifugal pump with an integrally cast self‑priming gas‑liquid separation chamber and recirculation ports. Compact and reliable – ideal where space and weight are limited.
Option B (modular combination with external vacuum unit): A standard API 610 centrifugal pump as the main pump, plus an external vacuum priming system suitable for hazardous areas. The vacuum unit evacuates the suction line before the main pump starts, then automatically shuts off once discharge pressure is established. Used for very high suction lift or special requirements.
| Parameter | Typical range |
|---|---|
| Flow range | 0.8 – 2,600 m³/h |
| Head range | 8 – 330 m |
| Working pressure | 2.5 – 5.0 MPa |
| Working temperature | –80°C to +450°C |
| Suction lift | Up to 9 m (at sea level) |
| Speed | Up to 2,980 rpm |
| Flange size | DN25 – DN300 |
| Suction size (example) | DN100 and above (e.g., 100ZX70-75) |
| Discharge size (example) | DN100 and above |
| Shaft power (example) | 24.2 kW (at 70 m³/h / 75 m head) |
Refineries: crude oil, refined products, acid/alkali solutions.
Chemical plants: sulphuric acid, hydrochloric acid, hydrofluoric acid, other corrosive liquids.
Tank truck unloading: fast self‑priming for liquid loading/unloading.
Oil fields & terminals: crude oil and product transfer.
Seawater lift: pump mounted on top deck (above sea level) using self‑priming to lift seawater to the main pump inlet.
Ballast operations: seawater lifting and discharge.
Shipbuilding: bilge, ballast, cargo transfer.
Cooling water circulation.
Seawater desalination.
Auxiliary systems in thermal and nuclear power plants.
Sewage pumping (fluids containing solids/sludge).
Flue gas desulphurisation (FGD) slurry transfer.
Ore and tailings slurry transfer.
Pulp and paper stock preparation.
Pharmaceutical and food liquid transfer.
Steel mill circulating water.
According to fluid properties, the casing and wetted parts can be made from various high‑quality materials:
| Fluid type | Recommended material |
|---|---|
| Clean / slightly dirty liquids | Cast iron |
| Corrosive media | Austenitic stainless steel (304/316/316L) |
| Strong acids / alkalis | Duplex stainless steel, titanium alloy |
| High temperature / high pressure | High‑quality carbon steel (with heating/cooling jacket) |
| Special aggressive environments | Hastelloy and other superalloys |
The seal system uses a cartridge single or double mechanical seal. The seal chamber complies with API 682, accepting single, double, tandem, or cartridge arrangements.
When selecting a self‑priming pump, consider the following key factors:
Fluid properties
Name and physico‑chemical characteristics (corrosive, flammable, toxic, etc.)
Temperature (determines materials and need for cooling/heating jacket)
Density and viscosity (affects power consumption)
Presence and size of solids (determines impeller and flow passage design)
Performance parameters
Rated flow (m³/h)
Required head (calculate from pipe length, vertical and horizontal distances, diameter, number of bends/valves, terminal pressure)
Suction lift (must not exceed the pump’s maximum; adjust for local atmospheric pressure)
Duty cycle (intermittent or continuous)
Installation & environment
Pump location relative to water source (vertical height and horizontal distance)
Hazardous area classification (requires explosion‑proof motor and ATEX accessories)
Ambient temperature (affects casing material and auxiliary systems)
Priming time check: For applications with specific self‑priming performance requirements, generally the priming time at maximum suction lift should not exceed 180 seconds. Dry priming time (6 m lift) is typically ≤3 minutes.
No manual priming: After initial fill, no manual priming or foot valve needed – simplifies piping and improves safety.
High suction lift: Up to 9 metres, fast priming time – quickly removes air from suction line.
API 610 compliant: OH1/OH2 design, suitable for severe petrochemical service.
Back pull‑out modular design: Standard bearing housing – maintenance without disturbing piping.
Optimised gas‑liquid separator: Higher efficiency and more stable performance than conventional external‑mixing self‑priming pumps.
Multiple seal configurations: API 682 seal chamber accepts single, double, tandem or cartridge seals.
Double volute casing: For DN80 and larger – balances radial forces, reduces vibration.
Explosion‑proof design: Suitable for flammable and hazardous atmospheres (ATEX available).
Every pump is tested before shipment:
Hydraulic performance test: Flow, head, efficiency, shaft power – verified to ISO 9906.
Self‑priming performance test: Suction lift and priming time measured.
Hydrostatic test: Casing pressure tested at 1.5× design pressure – no leakage.
Material certification: Certificates and traceability for all wetted parts.
Vibration & noise test: Verifies quiet and stable operation.
Inspect mechanical seal for leakage; check bearing temperature and vibration.
Ensure casing stored liquid is adequate (prevent loss under abnormal conditions).
Replace mechanical seal and related sealing elements according to service hours.
Check bearing lubrication and replenish or change oil/grease as required.
Drain the casing completely to avoid corrosion or crystallisation.
Apply rust preventive on wear parts or fill with protective fluid.
| Spare part | Recommended quantity |
|---|---|
| Mechanical seal kit | 1 set |
| Bearings (drive end and non‑drive end) | 1 set |
| Impeller (depending on corrosion/abrasion) | 1 piece |
| Gasket / O‑ring kit | 1 set |
| Shaft sleeve (if applicable) | 1 piece |
For a detailed selection based on your specific duty parameters (flow, head, suction lift, fluid properties, installation type, etc.), or to obtain technical data sheets, dimensional drawings, and a quotation, please contact our engineering team.
Email: info@hyrig.com
We provide reliable self‑priming pump solutions for petrochemical, offshore, water treatment, and industrial projects – efficient, safe, and designed for long‑term service.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.